Omega2+ fails to connect to wifi
@pvadam wwujjuuu muchas gracias, funciono totalmente
After many hours, wasted on Wifi connection problem resolving, find solution for me.
manually setup my Omega 2 WiFi network before start setup Omega2 (b160) in web mode after upgrade.
My home WiFi Ap name is 'dd-wrt'
Work usually in b/g mode with TKIP encription
Most successfully variant for me at start point - has been set WEP and 'no password mode' on router for upgrade Omega2 to (b160) version of firmware.
And I'd set back WPA-Personal mode and TKIP on Wifi router.
After as I made this, I meet only the troubles with my Omega2 connections.
My Omega 2 is:
Firmware 0.1.10 (b160)
Latest Firmware 0.1.10 (b160)
Linux Omega-4C77 4.4.46 #0 Thu Feb 2 23:46:03 2017 mips GNU/Linux
What I do for resolving connection problem:
Made factory reset via web interface (192.168.3.1)
Connect with Putty to 192.168.3.1 (ssh, port 22) as root/onioneer
root@Omega-4C77:~# vi /etc/config/wireless
change your ssid and password AND COUNTRY! from 'US' to 'CAN'. It is needed for WiFi change channel restrictions (I'm not sure, but... it's work):
warning: In Bold - options, which I changed from original values, but remember: it's must be in correlation with your wifi router settings. use omega2 linux command aps for router connect information. Something like a
6 dd-wrt c8:3a:35:ea:29:58 WPAPSK/TKIP 52 11b/g NONE In in my case
config wifi-device 'ra0'
option type 'ralink'
option mode '9'
option channel 'auto'
option txpower '100'
option ht '20'
option country 'CAN'
option disabled '0'
option device 'ra0'
option network 'wlan'
option mode 'ap'
option encryption 'psk2'
option key '12345678'
option ApCliEnable '1'
option ApCliSsid 'dd-wrt'
option ApCliAuthMode 'WPAPSK'
option ApCliEncrypType 'TKIP'
option ApCliPassWord '0015081975'
option ssid 'Omega-4C77'
- Save your work in vi: <esc> :wq
- root@Omega-4C77:~#service network restart, reconnect Putty
- check 'root@Omega-4C77:~# ping 184.108.40.206' - it must work now
- opkg update
- opkg install mc - it is not very important step ;)
- go again into web interface (192.168.3.1, btw, after as I connected to my Omega-4C77 AP again, it's already works as router - internet on PC is exists now), and step by step complete setup procedure.
But do not choose WiFi network setup, it's defined already at step 3. Choose "pass step".
Sorry for my Martian
So here's a good one for y'all couldn't get it to connect tried accessing it several times through web interface then through SSH no luck on either end
But then right as I was about to give up on it I took a smoke break and came back and low and behold the web interface worked... I really want to beat my head against the screen...
I must have read all these messages a hundred times without success and finally bought a new router that uses AES instead of TKIP and that was the breakthrough. So after owning two Omega2+ for 6-8 months and not being able to get past first base I started to build something useful. Then I connected an I2C device to one of them and found that the i2cdetect python command does not work There are many many messages devoted to this topic and again the developers of this product sit on their hands.
Life is too short to spend playing around with a bug ridden immature device such as the Omega2 so you've lost me Onion Community. Bin your Omega2 and sleep again at night.
@David-Lochlin je suis d'accord, dommage sa petite taille été un super avantage mais bon les développeurs on tellement passé de temps a vouloir le vendre a tout prix en dénigrant les autres produits du même genre qu'ils ont oublié de finir leurs propre produit.
Good. Really good answer. Enable appcli did the trick !
I have had the same issue with an Onion 2+, the annoying thing is, to get connectivity to the internet to see if an update works....
I fired up an Omega 1, which works no problem on the same wifi.
Then connect the wifi on the Omega 2 to the AP on the Omega 1 and so through.
So internet works, but wifi will still not connect to my wireless, so what has changed to make it not work between versions.
@MB hello, i suggest you do some searches on wifi router because last year there were many posts about the abilities of the omega2[+] to connect or not connect to some wireless router models. it seems the omega2 devices have problems with some models of wireless routers.
@Douglas-Kryder Yeah, thanks, I know it works with other wifi, I have it working on a wifi in my house, its more the fact that the Omega 2+ has poorer wifi support than the original omega, which connects fine. Just thought it was a downgrade in wifi support from the old one, more of me throwing that out there as an FYI.
For me the WiFi has also been a mayor pain in the ass. In the end I have now setup a Omega2 to connect to an original Omega which in turn connects to my WiFI network.
For those with Mikrotik routers.. I can confirm that Michal Rok's solution works..
i.e. you need to initially set the mode to 'sta' (in /etc/config/wireless) to allow Omega2+ to associate with a configured AP. The default mode of '9' cannot seem to associate with the configured AP even though it is visible. The trick in Michael's solution is the switch the mode to '9' as the last step in the boot process, in order to get an IP address.
Stupid.. but works. Not a good start to the Omega2+ journey!