We have upgraded the community system as part of the upgrade a password reset is required for all users before login in.

I have an Omega from Kickstarter shipment that does not boot



  • The instructions here https://wiki.onion.io/Tutorials/Reflash-The-Firmware-With-Ethernet-Expansion do not apply. Why might you ask? I have the testing firmware that was loaded to test the boards.

    U-Boot 1.1.4 (Aug 28 2015 - 16:51:26)
    
    AP121 (ar9331) U-boot
    
    DRAM:  64 MB
    Top of RAM usable for U-Boot at: 84000000
    Reserving 140k for U-Boot at: 83fdc000
    Reserving 192k for malloc() at: 83fac000
    Reserving 44 Bytes for Board Info at: 83fabfd4
    Reserving 36 Bytes for Global Data at: 83fabfb0
    Reserving 128k for boot params() at: 83f8bfb0
    Stack Pointer at: 83f8bf98
    Now running in RAM - U-Boot at: 83fdc000
    Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
    flash size 16777216, sector count = 256
    Flash: 16 MB
    Using default environment
    
    In:    serial
    Out:   serial
    Err:   serial
    Net:   ag7240_enet_initialize...
    No valid address in Flash. Using fixed address
    No valid address in Flash. Using fixed address
    : cfg1 0x5 cfg2 0x7114
    eth0: 00:03:7f:09:0b:ad
    eth0 up
    : cfg1 0xf cfg2 0x7214
    eth1: 00:03:7f:09:0b:ad
    athrs26_reg_init_lan
    ATHRS26: resetting s26
    ATHRS26: s26 reset done
    eth1 up
    eth0, eth1
    Hit any key to stop autoboot:  0
    ar7240> help
    reset   - Perform RESET of the CPU
    ?       - alias for 'help'
    boot    - boot default, i.e., run 'bootcmd'
    bootd   - boot default, i.e., run 'bootcmd'
    bootm   - boot application image from memory
    cp      - memory copy
    erase   - erase FLASH memory
    help    - print online help
    md      - memory display
    mm      - memory modify (auto-incrementing)
    mtest   - simple RAM test
    mw      - memory write (fill)
    nm      - memory modify (constant address)
    ping    - send ICMP ECHO_REQUEST to network host
    printenv- print environment variables
    progmac - Set ethernet MAC addresses
    run     - run commands in an environment variable
    setenv  - set environment variables
    tftpboot- boot image via network using TFTP protocol
    version - print monitor version
    ar7240> printenv
    bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),2752k(rootfs),13184k(uImage),64k(NVRAM),64k(ART)
    bootcmd=bootm 0x9f300000
    bootdelay=4
    baudrate=115200
    ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
    ipaddr=192.168.1.2
    serverip=192.168.1.10
    stdin=serial
    stdout=serial
    stderr=serial
    ethact=eth0
    
    Environment size: 361/65532 bytes
    ar7240>
    
    

    I need instructions to completely reflash this with the correct U-Boot and firmware. Serial works, if you can give me a TFTPBOOT capable image to load to the device I could boot from memory and flash it that way. Otherwise, it's useless and I'd like to get a replacement.


  • administrators

    @Andrew-Donnelly sorry for the delay, we've been looking at this and haven't found a way to upload the firmware using tftpboot.

    Can you file a support ticket on our helpdesk referencing this forum post? We'll send you a replacement Omega


Log in to reply
 

Looks like your connection to Community was lost, please wait while we try to reconnect.