I think this is another case where you have the test firmware. Several of us are in the same boat.

It seems that a number of us received omegas with test firmware. And once this is determined it seems that tech support goes silent.

Can someone provide us with a way forward....

I think this is another case where you have the test firmware. Several of us are in the same boat.

I think that this is yet another example of your Omega having the test firmware. You and several of us!!!!

Here is the output. Looks exactly like another user (Andrew Donnely) whom you are helping. Note I already opened a ticket with help desk. (Ticket 1068).

U-Boot 1.1.4 (Aug 28 2015 - 16:51:26)

AP121 (ar9331) U-boot

DRAM: 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 140k for U-Boot at: 83fdc000
Reserving 192k for malloc() at: 83fac000
Reserving 44 Bytes for Board Info at: 83fabfd4
Reserving 36 Bytes for Global Data at: 83fabfb0
Reserving 128k for boot params() at: 83f8bfb0
Stack Pointer at: 83f8bf98
Now running in RAM - U-Boot at: 83fdc000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16777216, sector count = 256
Flash: 16 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
Fetching MAC Address from 0x83ff4068
Fetching MAC Address from 0x83ff4068
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:11:40:00
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:11:40:01
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Hit any key to stop autoboot: 0
ar7240>help
reset - Perform RESET of the CPU
? - alias for 'help'
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootm - boot application image from memory
cp - memory copy
erase - erase FLASH memory
help - print online help
md - memory display
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
progmac - Set ethernet MAC addresses
run - run commands in an environment variable
setenv - set environment variables
tftpboot- boot image via network using TFTP protocol
version - print monitor version
ar7240>

Yes. Everything is fine unto step 5 when i get press any key to interrupt the boot sequence and i get to the uboot i do not get "Omega>" prompt. This is because (as i stated) this is the "testing image" (as reported by others).

As further proof: it asks me for a loggin : root with 5up (again as others reported)

The help command doesnt list http demon.

httpd does exist though and i tried launching it but it does not offer me to flash.

Again, I am not the only one that experienced this -- please provide me with the procedure to get my Omega up - given that i have your test image.

• I received an Omega with the testing firmware. The password is 5up....

• I have an ethernet expansion.

• I ran httpd and I can connect my browser to the Omega using 192.168.1.2 but nothing happens

• I looked around and found /usr/...www so I tried http -h /usr/,,,www but still no command to upload an image.

Help!!!!