OK.
I found the problem After I searched the tags.

opkg install ca-bundle

Writing out the problem gave me the answer. I followed the instruction in item 2 and all is working.
df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 7.8M 7.8M 0 100% /rom
tmpfs 60.9M 108.0K 60.8M 0% /tmp
/dev/sda1 14.6G 321.6M 13.5G 2% /overlay
overlayfs:/overlay 14.6G 321.6M 13.5G 2% /
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock6 22.1M 8.7M 13.3M 40% /mnt/mtdblock6
/dev/mtdblock7 512.0K 196.0K 316.0K 38% /mnt/mtdblock7

but I notice block detect still gives me
config 'mount'
option target '/mnt/sda1'
option uuid 'd5a4f036-3b7b-40e0-9423-e5fa9dd37ef2'
option enabled '0'

Also, I had to go back and change my /etc/rc.local to
SWAP_FILE="/overlay/swap.page" as it still showed /mnt/sda1
as described in the earlier section on swap files.

Hi,
I'm using
omega2+, firmware version b233.
(and loving it, mostly)

I'm trying to follow the pivot overlay instructions in the documentation and I am having less fun. There seem to be some inconsistencies in the docs. Not sure if this is the problem.

1. You mention that the USB drive should be mounted in /tmp/mounts/USB-A1. I don't see this .Is this just a doc error? Later, it recommends you mount /dev/sda1 on /mnt/sda1
2. The command
   mount /dev/<device name> /mnt/ ; tar -C /overlay -cvf - . | tar -C /mnt/ -xf - ; umount /mnt/
   Puts the upper and work directories in /mnt - is that what you want? I put them in /mnt/sda1
3. You suggest <<
   If your USB device uses one of the drivers from kmod-usb-storage-extras, you will need to run the following: ln -s /etc/modules.d/usb-storage-extras /etc/modules-boot.d/usb-storage-extras

How do you know if your USB device uses one of these drivers? A doc change would be a good idea here.
I added this symbolic link anyway.

When I reboot, the USB drive is not mounted. block detect shows
config 'global'
option anon_swap '0'
option anon_mount '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'

config 'mount'
option target '/mnt/sda1'
option uuid 'd5a4f036-3b7b-40e0-9423-e5fa9dd37ef2'
option enabled '0'
and
df -h doesn't show sda1 mounted
df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 7.8M 7.8M 0 100% /rom
tmpfs 60.9M 108.0K 60.8M 0% /tmp
/dev/mtdblock6 22.1M 8.7M 13.3M 40% /overlay
overlayfs:/overlay 22.1M 8.7M 13.3M 40% /
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock7 512.0K 196.0K 316.0K 38% /mnt/mtdblock7

dmesg shows a message
[ 12.537028] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.591808] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 12.611150] block: extroot: UUID mismatch (root: 2017e343-8e62014c-a4572a07-d0744c88, overlay: 8658bfb8-fb8bcbcf-706be5e8-ffaa3d7c)

One other thing about the docs. You say that if the firmware is updated, you need to save "your data". It's easy enough to save the home directory but is there any info on how to save all the software packages you downloaded or should you just keep a log of all the opkg calls you make.

What am I missing? I get
echo 1 >/sys/class/gpio/unexport
-bash: echo: write error: Invalid argument

OK.
I found the problem After I searched the tags.

opkg install ca-bundle

When I try to use git clone as below I get an error

git clone https://github.com/OnionIoT/oledQrCodeGenerator.git

Cloning into 'oledQrCodeGenerator'...
fatal: unable to access 'https://github.com/OnionIoT/oledQrCodeGenerator.git/': Error reading ca cert file /etc/ssl/certs/ca-certificates.crt - mbedTLS: (-0x3E00) PK - Read/write of file failed

ls -ld /etc/ssl/certs

drwxr-xr-x 2 root root 20411 Feb 2 15:46 /etc/ssl/certs

I am root.
ca-certificates.crt is not present

Any idea what I need to do to fix this?
*