thank you!

I uncommented the openwrt sources and ran the opkg update.
All, but 1 of them failed.

Collected errors:
 * opkg_download: Failed to download http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/onion/Packages.gz, wget returned 8.```

Where can I find this? It seems on the openwrt releases, the said path does not exist.

Thanks

root@omega:~# cat /etc/opkg/distfeeds.conf
src/gz openwrt_core http://downloads.openwrt.org/releases/18.06-SNAPSHOT/targets/ramips/mt76x8/packages
src/gz openwrt_base http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/base
src/gz openwrt_luci http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/luci
src/gz openwrt_onion http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/onion
src/gz openwrt_packages http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/packages
src/gz openwrt_routing http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/routing
src/gz openwrt_telephony http://downloads.openwrt.org/releases/18.06-SNAPSHOT/packages/mipsel_24kc/telephony
src/gz omega2_core http://repo.onioniot.com/omega2/packages/core
src/gz omega2_base http://repo.onioniot.com/omega2/packages/base
src/gz omega2_packages http://repo.onioniot.com/omega2/packages/packages
src/gz omega2_routing http://repo.onioniot.com/omega2/packages/routing
src/gz omega2_onion http://repo.onioniot.com/omega2/packages/onion

@crispyoz this tracks!
I will add this in my (personal) wiki about the board

@crispyoz this is correct

But hey, never mind this problem.
I reflashed the firmware and the problem went away

$ sysupgrade omega2p-v0.3.2-b218.bin

Thank you for your help!

@crispyoz no dice
I did both enable and start and then connected to internet and rebooted, and still it came up like firstboot.
Next time it booted, I connected to internet and then enabled and started network and then reboot; still the same.

Did both the above a couple of times.

service network enable
service network start

@crispyoz sorry to bother again.
But I just realised that every time I reboot the omega2+, it resets the web console like it did earlier with 'firstboot'

Earlier when I said it was rebooting fine, it was... but I was only connected to the serial console and didn't realise that it was disconnected from my internet connection every time I rebooted.

What may be this issue?

@Lazar-Demin any news on OpenWRT 21.02? (polite question)

@crispyoz thank you very much!

I agree with your point about insufficient power supply and will ensure to provide enough current for stable usage of op2+

@crispyoz Understood

I don't know why, though since after following your steps, it works well even after a couple of reboots.

One last question, the firmware repo shows the latest firmware is omega2p-v0.3.3-b253.bin, but on the onion, it already shows I am on the latest (my firmware is higher than the latest?)

Is this ok?

@crispyoz that worked!

The Onion2+ just gave me a wifi AP and after connecting to it, it also showed up the new setup window on the http wizard!

Can you tell me what had happened and how did disabling the network solve it?