Ok, I must've not done the reset correctly. It's worked now.
firstboot sync reboot
Thanks for your help :)
I assumed a factory reset was my only option. Hopefully all the code I had on there is in repositories anyway, so I'm hoping it won't matter too much.
It does seem very strange that the problem with that package still exists after the factory reset. I'll try and get some more information.
I've done the factory reset, and now the access point comes up and I can connect to it. When I try to run
wifisetup I keep getting the same
Error relocating /lib/libubus.so: uloop_cancelling: symbol not found over and over again.
Potentially the same issue as in this post: https://community.onion.io/post/15469
Hey. Thanks. I managed to connect via serial. This is the last page of output:
[ 4.263776] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz [ 4.269118] ehci-platform 101c0000.ehci: EHCI Host Controller [ 4.274983] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 4.283164] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 4.308675] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 4.316167] hub 1-0:1.0: USB hub found [ 4.320409] hub 1-0:1.0: 1 port detected [ 4.329459] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.337382] ohci-platform: OHCI generic platform driver [ 4.343043] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 4.350017] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 4.358133] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.423797] hub 2-0:1.0: USB hub found [ 4.428044] hub 2-0:1.0: 1 port detected [ 4.445410] MTK MSDC device init. [ 4.488808] mtk-sd: MediaTek MT6575 MSDC Driver [ 4.496803] sdhci: Secure Digital Host Controller Interface driver [ 4.503152] sdhci: Copyright(c) Pierre Ossman [ 4.509064] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.519467] usbcore: registered new interface driver usb-storage [ 4.529148] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.546978] init: - preinit - [ 5.389621] rt3050-esw 10110000.esw: link changed 0x00 Press the [f] key and hit [enter] to enter failsafe mode Press the , ,  or  key and hit [enter] to select the debug[ 5.589270] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available) level [ 8.436149] jffs2: notice: (396) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 8.455942] mount_root: switching to jffs2 overlay [ 8.493035] urandom-seed: Seeding with /etc/urandom.seed Error relocating /lib/libubus.so: uloop_cancelling: symbol not found [ 8.617476] watchdog watchdog0: watchdog did not stop! [ 8.622934] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00 [ 8.622934] [ 8.633759] Rebooting in 1 seconds..
I remember seeing the
Error relocating /lib/libubus.so: uloop_cancelling: symbol not found or something similar while I was doing some
opkg upgrade ..., so presumably it's related to that.
Hi. I hadn't used my Omega 2+ in a while, so ran
opkg update yesterday and saw that there were a load of packages that need upgrading. There doesn't seem to be a way to upgrade everything, so I started upgrading a few of them individually. After I did
opkg upgrade opkg opkg seemed to stop working.
I did a reboot to see if that would help, but the Omega won't start up properly now. The orange light comes on for about 8 seconds, then flashes for 3 or 4 seconds, then the light goes out. The WiFi access point never becomes available, so I can't connect to it.
I've tried to do a factory reset several times, but holding down the reset button, but nothing seems to happen.
Has anyone got any ideas? Thanks.
Hi. I've been using the Relay Expansion to switch the pump for my garden pond on at off at an interval.
The other week I noticed that it was on constantly. I assumed it was a software problem, but after investigating, realised that the relay still seemed to be switching on and off, but somehow the circuit is remaining closed.
I rewired to used the other channel on the Relay Expansion and that was working fine for a week or so, but the same thing has just happened. The electricity is constantly on, even when the relay appears to be switched off.
Has anyone experienced this before?
Looks like your connection to Community was lost, please wait while we try to reconnect.