@Martin-Gagnon Omega2 Firmware Flashing from USB Storage (original FW omega2-v0.1.10-b160).

http://repo.onion.io.s3.amazonaws.com/omega2/images/omega2-v0.2.0-b197.bin
omega2-v0.2.0-b197.bin I have renamed to omega2.bin and copied to a FAT-32 formatted USB stick.

MD5 checksum:
omega2.bin.md5
0553e7b13d2d02427ec24b0445520a28 *omega2.bin

Be patient! UBoot says:

[!] This will take several minutes * please do not power off your Omega2 *

Here you are my Serial Console log. Your log may differ due to your USB stick.

____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/" Board: Onion Omega2 APSoC DRAM: 64 MB relocate_code Pointer at: 83f60000 flash manufacture id: ef, device id 40 18 find flash: W25Q128BV *** Warning - bad CRC, using default environment ============================================ Onion Omega2 UBoot Version: 4.3.0.3 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 18 2016 Time:17:30:55 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 CPU freq = 575 MHZ Estimated memory size = 64 Mbytes Resetting MT7628 PHY. Initializing MT7688 GPIO system. ************************************** * Hold Reset button for more options * ************************************** You have 40 seconds left to select a menu option... Please select option: [ Enter ]: Boot Omega2. [ 0 ]: Start Web recovery mode. [ 1 ]: Start command line mode. [ 2 ]: Flash firmware from USB storage. Option [2] selected. System Load Linux then write to Flash via USB Storage. Looking for a USB Storage. If suitable image is found on USB Storage writing to Flash will be attempted. U-Boot will look for a FAT file system. (Re)start USB... LOW LEVEL INIT USB0: Scanning bus 0 for devices... New Device 0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x8 usb_control_msg: status = success? INSIDE USB INIT INSIDE USB INIT: Device responded. set address 1 usb_control_msg: request: 0x5, requesttype: 0x0 value 0x1 index 0x0 length 0x0 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x12 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x9 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x19 usb_control_msg: status = success? get_conf_no 0 Result 25, wLength 25 if 0, ep 0 ##EP epmaxpacketin[1] = 2 set configuration 1 usb_control_msg: request: 0x9, requesttype: 0x0 value 0x1 index 0x0 length 0x0 usb_control_msg: status = success? new device strings: Mfr=0, Product=1, SerialNumber=0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x300 index 0x0 length 0xFF usb_control_msg: status = success? USB device number 1 default language ID 0x409 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x301 index 0x409 length 0xFF usb_control_msg: status = success? Manufacturer Product OHCI Root Hub SerialNumber Device is a hub? usb_control_msg: request: 0x6, requesttype: 0xA0 value 0x2900 index 0x0 length 0x4 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0xA0 value 0x2900 index 0x0 length 0x9 usb_control_msg: status = success? usb_control_msg: request: 0x0, requesttype: 0xA0 value 0x0 index 0x0 length 0x4 usb_control_msg: status = success? usb_control_msg: request: 0x1, requesttype: 0x23 value 0x8 index 0x1 length 0x0 usb_control_msg: status = success? usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 usb_control_msg: status = success? usb_control_msg: request: 0x3, requesttype: 0x23 value 0x8 index 0x1 length 0x0 usb_control_msg: status = success? usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 usb_control_msg: status = success? usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 usb_control_msg: status = success? usb_control_msg: request: 0x1, requesttype: 0x23 value 0x10 index 0x1 length 0x0 usb_control_msg: status = success? usb_control_msg: request: 0x3, requesttype: 0x23 value 0x4 index 0x1 length 0x0 usb_control_msg: status = success? usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 usb_control_msg: status = success? usb_control_msg: request: 0x1, requesttype: 0x23 value 0x14 index 0x1 length 0x0 usb_control_msg: status = success? New Device 1 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x8 usb_control_msg: status = success? INSIDE USB INIT INSIDE USB INIT: Device responded. usb_control_msg: request: 0x5, requesttype: 0x0 value 0x2 index 0x0 length 0x0 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x12 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x9 usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x20 usb_control_msg: status = success? get_conf_no 0 Result 32, wLength 32 if 0, ep 0 if 0, ep 1 ##EP epmaxpacketout[1] = 64 ##EP epmaxpacketin[2] = 64 set configuration 1 usb_control_msg: request: 0x9, requesttype: 0x0 value 0x1 index 0x0 length 0x0 usb_control_msg: status = success? new device strings: Mfr=1, Product=2, SerialNumber=3 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x300 index 0x0 length 0xFF usb_control_msg: status = success? USB device number 2 default language ID 0x409 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x301 index 0x409 length 0xFF usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x302 index 0x409 length 0xFF usb_control_msg: status = success? usb_control_msg: request: 0x6, requesttype: 0x80 value 0x303 index 0x409 length 0xFF usb_control_msg: status = success? Manufacturer Kingston Product DataTraveler 3.0 SerialNumber 60A44C4139D4AF40D000360D Device is a hub? 2 USB Device(s) found scan end Scanning bus for storage devices... ================================================= 1: Hub, USB Revision 1.10 - OHCI Root Hub - Class: Hub - PacketSize: 8 Configurations: 1 - Vendor: 0x0000 Product 0x0000 Version 0.0 ================================================= 2: Mass Storage, USB Revision 2.10 - Kingston DataTraveler 3.0 60A44C4139D4AF40D000360D - Class: (from Interface) Mass Storage - PacketSize: 64 Configurations: 1 - Vendor: 0x0951 Product 0x1666 Version 1.0 Testing BULK mode...Identifying a storage device...* USB_STORAGE: 1 Storage Device(s) found *************************************** * [!] This will take several minutes * * please do not power off your Omega2 * *************************************** * * Reading file "omega2.bin" * ******** ****** ******************************** ****** ****** ****** ************************************************************************************************************************************************************************************************************************************************************* * FAT: 7864492 Bytes read ........................................................................................................................ ........................................................................................................................ . . Done! ____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/" Board: Onion Omega2 APSoC DRAM: 64 MB relocate_code Pointer at: 83f60000 ****************************** Software System Reset Occurred ****************************** flash manufacture id: ef, device id 40 18 find flash: W25Q128BV *** Warning - bad CRC, using default environment ============================================ Onion Omega2 UBoot Version: 4.3.0.3 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 18 2016 Time:17:30:55 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 CPU freq = 575 MHZ Estimated memory size = 64 Mbytes Resetting MT7628 PHY. Initializing MT7688 GPIO system. ************************************** * Hold Reset button for more options * ************************************** Boot Linux from Flash NO RESET PRESSED. ## Booting image at bc050000 ... Image Name: MIPS LEDE Linux-4.4.74 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1341898 Bytes = 1.3 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 4.4.74 (root@3fbe4dcb626f) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3484-d8f14ba) ) #0 Tue Jul 31 16:32:08 2018 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc) [ 0.000000] MIPS: machine is Onion Omega2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0006df20 [ 0.000000] Readback ErrCtl register=0006df20 [ 0.000000] Memory: 60512K/65536K available (3103K kernel code, 145K rwdata, 740K rodata, 164K init, 196K bss, 5024K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] intc: using register map from devicetree [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource_probe: no matching clocksources found [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.007520] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.070041] pid_max: default: 32768 minimum: 301 [ 0.074636] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080972] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.094612] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.104122] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.110126] pinctrl core: initialized pinctrl subsystem [ 0.115898] NET: Registered protocol family 16 [ 0.140969] mt7621_gpio 10000600.gpio: registering 32 gpios [ 0.146509] mt7621_gpio 10000600.gpio: registering 32 gpios [ 0.151927] mt7621_gpio 10000600.gpio: registering 32 gpios [ 0.158521] i2c-mt7621 10000900.i2c: clock 100 kHz [ 0.164268] clocksource: Switched to clocksource MIPS [ 0.170825] NET: Registered protocol family 2 [ 0.176031] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.182720] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.188908] TCP: Hash tables configured (established 1024 bind 1024) [ 0.195101] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.200698] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.207087] NET: Registered protocol family 1 [ 0.217556] Crashlog allocated RAM at address 0x3f00000 [ 0.238856] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.244508] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.257290] io scheduler noop registered [ 0.261033] io scheduler deadline registered (default) [ 0.266952] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm [ 0.276034] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22 [ 0.282031] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux [ 0.291444] mtk-pwm 10005000.pwm: Error applying setting, reverse things back [ 0.298798] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.306243] console [ttyS0] disabled [ 0.309676] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A [ 0.318452] console [ttyS0] enabled [ 0.318452] console [ttyS0] enabled [ 0.325442] bootconsole [early0] disabled [ 0.325442] bootconsole [early0] disabled [ 0.334077] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A [ 0.343601] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A [ 0.354166] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 0.364360] m25p80 spi32766.0: using chunked io (size=31) [ 0.369851] m25p80 spi32766.0: w25q128 (16384 Kbytes) [ 0.375020] 4 ofpart partitions found on MTD device spi32766.0 [ 0.380933] Creating 4 MTD partitions on "spi32766.0": [ 0.386163] 0x000000000000-0x000000030000 : "u-boot" [ 0.392989] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.400314] 0x000000040000-0x000000050000 : "factory" [ 0.407347] 0x000000050000-0x000001000000 : "firmware" [ 0.434873] 2 uimage-fw partitions found on MTD device firmware [ 0.440901] 0x000000050000-0x000000197a0a : "kernel" [ 0.447601] 0x000000197a0a-0x000001000000 : "rootfs" [ 0.454488] mtd: device 5 (rootfs) set to be root filesystem [ 0.460300] 1 squashfs-split partitions found on MTD device rootfs [ 0.466603] 0x0000007c0000-0x000001000000 : "rootfs_data" [ 0.484675] rt3050-esw 10110000.esw: link changed 0x00 [ 0.491689] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.500339] i2c /dev entries driver [ 0.504528] mt7621_wdt 10000120.watchdog: Initialized [ 0.511189] NET: Registered protocol family 10 [ 0.519885] NET: Registered protocol family 17 [ 0.524569] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.537391] 8021q: 802.1Q VLAN Support v1.8 [ 0.549391] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.557522] Freeing unused kernel memory: 164K (803e7000 - 80410000) [ 1.839969] init: Console is alive [ 1.843641] init: - watchdog - [ 4.422542] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.591187] usbcore: registered new interface driver usbfs [ 4.596937] usbcore: registered new interface driver hub [ 4.602436] usbcore: registered new device driver usb [ 4.613785] exFAT: Version 1.2.9 [ 4.657253] SCSI subsystem initialized [ 4.667997] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.676418] ehci-platform: EHCI generic platform driver [ 4.692095] phy phy-10120000.usbphy.0: remote usb device wakeup disabled [ 4.698912] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz [ 4.704243] ehci-platform 101c0000.ehci: EHCI Host Controller [ 4.710123] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 4.718289] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 4.744313] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 4.751820] hub 1-0:1.0: USB hub found [ 4.756056] hub 1-0:1.0: 1 port detected [ 4.765074] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.773016] ohci-platform: OHCI generic platform driver [ 4.778670] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 4.785637] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 4.793753] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.859456] hub 2-0:1.0: USB hub found [ 4.863703] hub 2-0:1.0: 1 port detected [ 4.880862] MTK MSDC device init. [ 4.924445] mtk-sd: MediaTek MT6575 MSDC Driver [ 4.932435] sdhci: Secure Digital Host Controller Interface driver [ 4.938784] sdhci: Copyright(c) Pierre Ossman [ 4.944734] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.955146] usbcore: registered new interface driver usb-storage [ 4.964983] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.982797] init: - preinit - [ 5.209981] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 5.519778] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available) [ 5.529614] usb-storage 1-1:1.0: USB Mass Storage device detected [ 5.548865] scsi host0: usb-storage 1-1:1.0 [ 5.925612] rt3050-esw 10110000.esw: link changed 0x00 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.545757] scsi 0:0:0:0: Direct-Access KINGSTON DataTraveler 3.0 1.01 PQ: 0 ANSI: 6 [ 6.556955] sd 0:0:0:0: [sda] 15187968 512-byte logical blocks: (7.78 GB/7.24 GiB) [ 6.565674] sd 0:0:0:0: [sda] Write Protect is off [ 6.571278] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 6.585188] sda: [ 6.590658] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 9.187579] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 9.201830] urandom-seed: Seed file not found (/etc/urandom.seed) [ 9.436319] procd: - early - [ 9.439361] procd: - watchdog - [ 10.088140] procd: - watchdog - [ 10.091609] procd: - ubus - [ 10.266096] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.275836] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.285066] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.294695] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.303848] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.313200] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.322573] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) [ 10.332140] procd: - init - Please press Enter to activate this console. [ 10.851472] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.890023] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 10.959395] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.985665] gdma-rt2880 10002800.gdma: revision: 3, channels: 16 [ 11.430891] [ 11.430891] [ 11.430891] === pAd = c0572000, size = 1182848 === [ 11.430891] [ 11.441793] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628)) [ 11.514473] Linux video capture interface: v2.00 [ 11.558420] hidraw: raw HID events driver (C) Jiri Kosina [ 11.583469] ralink-i2s 10000a00.i2s: mclk 480KHz [ 11.591580] max98090 0-0010: Failed to reset codec: -6 [ 11.597049] max98090 0-0010: Failed to read device revision: -1 [ 11.603054] max98090 0-0010: ASoC: failed to probe component -1 [ 11.609718] asoc-simple-card sound: ASoC: failed to instantiate card -1 [ 11.616572] asoc-simple-card: probe of sound failed with error -1 [ 11.644907] Bluetooth: Core ver 2.21 [ 11.648646] NET: Registered protocol family 31 [ 11.653150] Bluetooth: HCI device and connection manager initialized [ 11.659646] Bluetooth: HCI socket layer initialized [ 11.664606] Bluetooth: L2CAP socket layer initialized [ 11.669757] Bluetooth: SCO socket layer initialized [ 11.677281] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 11.682681] Bluetooth: BNEP filters: protocol multicast [ 11.688062] Bluetooth: BNEP socket layer initialized [ 11.699988] usbcore: registered new interface driver btusb [ 11.709712] usbcore: registered new interface driver cdc_acm [ 11.715542] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 11.727498] Bluetooth: HCI UART driver ver 2.3 [ 11.732020] Bluetooth: HCI UART protocol H4 registered [ 11.737300] Bluetooth: HCI UART protocol BCSP registered [ 11.746909] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 11.752941] Bluetooth: HIDP socket layer initialized [ 11.761097] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.782644] nf_conntrack version 0.5.0 (948 buckets, 3792 max) [ 11.813032] Bluetooth: RFCOMM TTY layer initialized [ 11.818078] Bluetooth: RFCOMM socket layer initialized [ 11.823313] Bluetooth: RFCOMM ver 1.11 [ 11.842598] usbcore: registered new interface driver ums-alauda [ 11.851651] usbcore: registered new interface driver ums-cypress [ 11.860903] usbcore: registered new interface driver ums-datafab [ 11.869913] usbcore: registered new interface driver ums-freecom [ 11.879043] usbcore: registered new interface driver ums-isd200 [ 11.888305] usbcore: registered new interface driver ums-jumpshot [ 11.897387] usbcore: registered new interface driver ums-karma [ 11.907232] usbcore: registered new interface driver ums-sddr09 [ 11.916363] usbcore: registered new interface driver ums-sddr55 [ 11.925851] usbcore: registered new interface driver ums-usbat [ 11.938133] usbcore: registered new interface driver usbhid [ 11.943795] usbhid: USB HID core driver [ 11.951554] usbcore: registered new interface driver usblp [ 11.965679] usbcore: registered new interface driver usbserial [ 11.971707] usbcore: registered new interface driver usbserial_generic [ 11.978489] usbserial: USB Serial support registered for generic [ 11.997225] Driver for 1-wire Dallas network protocol. [ 12.023565] xt_time: kernel timezone is -0000 [ 12.030444] usbcore: registered new interface driver ch341 [ 12.036191] usbserial: USB Serial support registered for ch341-uart [ 12.045015] usbcore: registered new interface driver cp210x [ 12.050796] usbserial: USB Serial support registered for cp210x [ 12.060394] usbcore: registered new interface driver ftdi_sio [ 12.066440] usbserial: USB Serial support registered for FTDI USB Serial Device [ 12.088576] usbcore: registered new interface driver pl2303 [ 12.094428] usbserial: USB Serial support registered for pl2303 [ 12.105968] PPP generic driver version 2.4.2 [ 12.113497] NET: Registered protocol family 24 [ 12.131345] usbcore: registered new interface driver snd-usb-audio [ 12.153186] usbcore: registered new interface driver uvcvideo [ 12.159091] USB Video Class driver (1.1.1) [ 12.171803] usbcore: registered new interface driver option [ 12.177665] usbserial: USB Serial support registered for GSM modem (1-port) [ 12.190329] kmodloader: done loading kernel modules from /etc/modules.d/* [ 12.423717] random: jshn: uninitialized urandom read (4 bytes read, 31 bits of entropy available) [ 12.501609] random: jshn: uninitialized urandom read (4 bytes read, 31 bits of entropy available) [ 24.005792] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready [ 24.646803] [ 24.646803] _ _____ ___ ___ _________ ___ ____ [ 24.646803] | | /| / / _ | / _ \/ _ \ / ___/ __ \/ _ \/ __/ V1.0 [ 24.646803] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/ [ 24.646803] |__/|__/_/ |_/_/|_/_/ \___/\____/_/|_/___/ [ 24.646803] Onion Enhanced MT7688 WiFi Driver [ 24.646803] [ 25.035852] DMA Scheduler Mode=0(LMAC) [ 25.039685] efuse_probe: efuse = 10000012 [ 25.043810] 1. Phy Mode = 14 [ 25.220267] 2. Phy Mode = 14 [ 25.223240] 3. Phy Mode = 14 [ 25.240613] WTBL Segment 1 info: [ 25.243992] MemBaseAddr/FID:0x28000/0 [ 25.247936] EntrySize/Cnt:32/128 [ 25.251383] WTBL Segment 2 info: [ 25.254749] MemBaseAddr/FID:0x40000/0 [ 25.258636] EntrySize/Cnt:64/128 [ 25.262080] WTBL Segment 3 info: [ 25.265452] MemBaseAddr/FID:0x42000/64 [ 25.269426] EntrySize/Cnt:64/128 [ 25.272870] WTBL Segment 4 info: [ 25.276242] MemBaseAddr/FID:0x44000/128 [ 25.280305] EntrySize/Cnt:32/128 [ 32.736330] device ra0 entered promiscuous mode [ 32.741073] br-wlan: port 1(ra0) entered forwarding state [ 32.746663] br-wlan: port 1(ra0) entered forwarding state [ 32.752923] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready [ 34.744281] br-wlan: port 1(ra0) entered forwarding state [ 39.553145] device ra0 left promiscuous mode [ 39.557711] br-wlan: port 1(ra0) entered disabled state [ 39.972252] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready [ 40.978087] device ra0 entered promiscuous mode [ 40.982828] br-wlan: port 1(ra0) entered forwarding state [ 40.988419] br-wlan: port 1(ra0) entered forwarding state [ 40.995159] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready [ 42.984281] br-wlan: port 1(ra0) entered forwarding state [ 57.907885] random: nonblocking pool is initialized [ 106.803425] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 106.810668] jffs2_build_filesystem(): unlocking the mtd device... done. [ 106.817413] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 107.949950] FAT-fs (sda): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 138.196810] done. [ 138.198822] jffs2: notice: (1699) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. BusyBox v1.25.1 () built-in shell (ash) ____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/ ----------------------------------------------------- Ω-ware: 0.2.0 b197 ----------------------------------------------------- root@Omega-5533:/#

Next step: wifisetup ...