Hi everyone,
For my project i am using Omega2+ where i need to have Ethernet and WIFI both connectivity, but ethernet as primary.

I had used ethernet Jack, soldered on general dot matrix pcb with all resistor and capacitor as described in ethernet expansion schematic. I tested ethernet, its working good.

My objective is to run python MQTT publish and subscribe on available network (WIFI-Ethernet) at any point. Where Ethernet need to give 1st preference if both Ethernet and WIFI are available.

Problem i am facing is auto switching between network( Ethernet - WIFI ) not happening. There are different cases which i came across:

1. If i keep Ethernet during boot, then omega gets IP through DHCP form router and MQTT working fine.
2. Same if keep only WIFI, omega gets IP and MQTT works fine.
3. But if omega booted with active wifi network , and then if i had connected ethernet and disconnected WIFI by turning off SSID. MQTT does not work, even though omega got IP with ethernet.

Kindly explain how i can configure network on Omega2 so that both Ethenet and WIFI should work with auto switching between available active network (ethernet and wifi). And giving ethernet as primary network

Scripts are in /etc/hotplug.d/

My ethernet and WIFI both working, but switching of network between Ethernet and WIFI does not work. I feel always omega is looking for WIFI network only.

Most of the time i feel ethernet does not getting registered. Please look below image

Sometime , if ethernet got registered (checked in ifconfig) but omega does not takes that network. It keeps looking for WIFI

Please response soon
Regards
Suman

Kindly explain how i can configure network on Omega2 so that both Ethenet and WIFI should work with auto switching between available active network (ethernet and wifi). And giving ethernet as primary network

I want to achieve auto selection of available active network between WIFI and Ethernet, with Ethernet on 1st priority if both network available.

I was trying to get Ethernet working, but facing issue. Above picture shows that Omega2+ keep trying to setup Ethernet but fails and keep repeating it

I think now it is clear, kindly support.

As i said i am new to the linux environment, so please explain in detail how i can make out.

Thanks

Step 1, if you disable wifi, does the ethernet device reliably connect, remain connected and function correctly.

Step 2) if you enable wifi does this have an impact upon the functionalty of the ethernet.

Depending on the answer to these two questions you will decide how best to proceed.

After that i tested ethernet plugging and un-plugging many times. Its work and getting identified by omega and registered. Also ping test work. you can see below image

But after enabling WIFI :

1. I rebooted Omega with Ethernet connected, then did ping test it was good working.
2. After this connected Omega with WIFI also, at this point omega was having both ethernet and WIFI network. Then did ping test again i saw response time got increased. From here i discovered that omega is talking through WIFI not ethernet.
3. Then i disconnected WIFI and keeping ethernet as it is, and found ping test not working.
   which i feel because Omega is searching WIFI only.

How i can change network priority between Ethernet and WIFI. Ethernet need to be at 1st priority. WIFI needed just as fallback network, If ethernet not working then search for WIFI

Please response soon, what i should do next
Thanks

I don't know any way to set a priority on an interface on OpenWrt, but you could achieve something like this via a hotplug script on interface up and down etc, but a static ip is a much easier method if that will work for your specific task.

If you look in /etc/config/network you can set the options on your interface eth0, you can see which options to set by looking at wlan setup.

ok crispyoz can you tell me if ethernet is active (got IP, pinging works), why omega2 does not go back to ethernet when wifi is disconnected ?

1. My advice
   If you always ask someone else to give you a solution, then you might solve your problem more quickly but you'll always have a lot of problems. If you ask for guidance on how to come to a solution then your solution will be arrived at with a whole lot of learning along the way.

2. My guidance

When an interface comes up or goes down, this hotplug script is executed:

/etc/hotplug.d/iface/00-netstate

Spend some time reading up on the hotplug infrastructure and you can find your solution. It's just a scripting system that is triggered whenever an interface (or other device) comes up of goes down (or other relevant action). So think of it as a see-saw, if if1 comes up, execute if2 down, if if2 comes up execute if1 down.

Don't be daunted by the fact that someone more experienced wrote the exiting script, it was designed to be generic. You need something a bit different, so just write it.

Yes i am new to this field accepted. Does Omega is for only experienced person ? please tell me.

Don't judge me just because i asked you for the help, and listen one more thing till now what ever solution i got from Omega community it was never end to end or complete guideline.
But then also i made good progress on Omega2 by just getting suggestions. I had done mosquitto MQTT and SSL, python based MQTT and SSL. Made SSL with AWS in python and lot more. This all i created. No body from Omega community given ready made code.

I have read almost all post related to my problem on Omega community. From last 3 months i am reading and trying everything. I tried Linkit 7688 then dragino YUN and then started on Omega2.
Don't ever think that i am sitting and asking everything from Omega team.

If you don't want to give response, its ok. But don't say this things

Try it out and let us know how it goes

Are you saying about this, under eth0 or wan interface of Omega i need to put above two settings ?