Created a network with a hidden SSID, no auth. Manually configured it in config/wireless. No dice. What's notable is zero packets are received with any of these failures:

eth0.2    Link encap:Ethernet  HWaddr 40:A3:6B:C0:42:42
          inet6 addr: fe80::42a3:6bff:fec0:4242/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:46 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:13848 (13.5 KiB)

My router is on channel 1, fwiw.

Next step: changed wifi-iface.ApCliEnable to 1. No change.

set the debug flag in wifisetup, reran. Output:

Current Count: 1
Number of configured nets: 1
trying to connect to... "networkname"
wwan network is set up... false,
ran out of configured networks... no station available
Wifi manager finished

@György-Farkas said in Omega2: can't connect to wifi after setup. How to debug?:

@Ted-Timmons

According to your uci show

wireless.@wifi-iface[0].ApCliEnable='0'
You simply disabled Omega's Wifi client.

What about Omega's Wifi AP?
wireless.ra0.disabled='1' means the AP (more exactly the whole Wifi system) is disabled
wireless.ra0.disabled='0' means the AP is enabled

I did a factory restore, disabled=0, at least now. Presumably it's been that way because I can't connect to it over serial/USB anyhow.

As I said, I did a factory restore, then did a setup to a network without a hyphen. I notice the wireless.@wifi-iface[0].Ap* entries are added by wifisetup; it also creates the wireless.@wifi-config[0]* entries. Those don't connect, though- I've tried rebooting and checking both ifconfig and route to see.

Finally, I tried adding device ra0 to the wifi-config, it didn't make a difference.

# wifisetup info
{ "success": false }

# route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.3.0     *               255.255.255.0   U     0      0        0 br-wlan

# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd1d:48c4:7633::/48'
network.wlan=interface
network.wlan.type='bridge'
network.wlan.ifname='eth0.1'
network.wlan.proto='static'
network.wlan.ipaddr='192.168.3.1'
network.wlan.netmask='255.255.255.0'
network.wlan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'

# uci show wireless
wireless.ra0=wifi-device
wireless.ra0.type='ralink'
wireless.ra0.mode='9'
wireless.ra0.channel='auto'
wireless.ra0.txpower='100'
wireless.ra0.ht='20'
wireless.ra0.country='US'
wireless.ra0.disabled='0'
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='ra0'
wireless.@wifi-iface[0].network='wlan'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].key='12345678'
wireless.@wifi-iface[0].ApCliAuthMode='WPA2PSK'
wireless.@wifi-iface[0].ApCliEncrypType='AES'
wireless.@wifi-iface[0].ssid='Omega-4242'
wireless.@wifi-iface[0].ApCliSsid='networkname'
wireless.@wifi-iface[0].ApCliPassWord='networkname'
wireless.@wifi-iface[0].ApCliEnable='0'
wireless.@wifi-config[0]=wifi-config
wireless.@wifi-config[0].ssid='networkname'
wireless.@wifi-config[0].encryption='WPA2PSK'
wireless.@wifi-config[0].key='networkpass'

@Richard-Berg said in Omega2: can't connect to wifi after setup. How to debug?:

Does you SSID by chance have a hyphen - in the name or an overly long name? Those 2 things have been discussed here recently to having it not connect to wifi.

hyphen, yes. Is there a fix/workaround? (besides renaming my network)

Nothing? I'd like to be able to use all my Onion hardware.

Omega2+. I can set it up in the web or cmdline, but after it reboots, it still isn't on my wifi network. (I've checked the dhcp list and used nmap to look for port 22). Here's some of the details I've found while looking around. What's next? I'm using the breadboard dock, I assume this dock doesn't provide serial output, I don't see it on my osx/macos USB list (system_profiler SPUSBDataType).

   Ω-ware: 0.1.5 b130

# wifisetup list
{ "results": [ { "ssid": "xxxx", "encryption": "WPA2PSK", "password": "yyyy" } ] }

# uci show
[...]
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='ra0'
wireless.@wifi-iface[0].network='wlan'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].key='(default)'
wireless.@wifi-iface[0].ApCliAuthMode='WPA2PSK'
wireless.@wifi-iface[0].ApCliEncrypType='AES'
wireless.@wifi-iface[0].ssid='Omega-wwww'
wireless.@wifi-iface[0].ApCliSsid='xxxxxxxx'
wireless.@wifi-iface[0].ApCliPassWord='yyyyyyyy'
wireless.@wifi-iface[0].ApCliEnable='0'
wireless.@wifi-config[0]=wifi-config
wireless.@wifi-config[0].ssid='xxxxxxxx'
wireless.@wifi-config[0].encryption='WPA2PSK'
wireless.@wifi-config[0].key='yyyyyyyy'