Making Omega2 talks with SAMD21 (Arduino Zero)

[Suman kumar Jha]

Hi György Farkas
Please response

[Suman kumar Jha]

Hi
Are you there, I am waiting for the response.
Kindly response anyone

[György Farkas]

@Suman-kumar-Jha I've lost the thread.

You installed the 'yunbridge' package and wrote:
Thanks, something better now.

I questioned:
What did you do previously? Did you change some settings? What was good and what was wrong?

No answer.

You upgraded to b227 manually and wrote:
After that i found new small problem.

I wrote
You should make a clean system (Factory Restore) ... and repeat the Initial Setup process again.
...
If your system will be OK...

You wrote:
Thanks, but I had tried this before putting message to you

Does it mean that your test arrangement (the whole HW, each SW and Omega2's firmware,) worked well before you installed and enabled 'yunbridge' again?

[Suman kumar Jha]

*After doing all the steps successfully, and booting back i installed python and yunbridge as you described all good done.

After that i found new small problem. My laptop and omega2 is on same wifi network, but "omega-CF2D.local" not working which was previously working.*

Above was my statement. For me YUN bridge never worked till now. And about above problem, i figured out what was the reason. Actually after i flashed firmware i forgot to reinstall omega arduino dock package.

Then i re-installed omega dock on arduino ide. Now omega-CF2D.local is working in browser and also arduino ide is detecting Omega2.

Coming to the topic, YUN bridge. You said (Formerly I supposed that python-light is enough but I was wrong.) What does mean, python light will not work? Should i install full python?

Also while trying YUN Bridge Console read, i felt omega dock is not communicating with Omega2.
on putty ssh
I am getting always
root@Omega-CF2D:~# telnet localhost 6571
telnet: can't connect to remote host (127.0.0.1): Connection refused

On which UART, Omega2 is interfaced with dock ?
Also on Omega2 side what is default baudrate for YUN bridge?

I had used this firmware

*#include <Bridge.h>
#include <Console.h>

SerialBridgeClass myBridge(Serial);

String name;

void setup() {
// Initialize Console and wait for port to open:
pinMode(13, OUTPUT);
digitalWrite(13, HIGH);
myBridge.begin();
ConsoleClass(myBridge);
Console.begin();
// Wait for Console port to connect
while (!Console);
digitalWrite(13, LOW);
Console.println("Hi, what's your name?");
}

void loop() {
if (Console.available() > 0) {
char c = Console.read(); // read the next char received
// look for the newline character, this is the last character in the string
if (c == '\n') {
//print text with the name received
Console.print("Hi ");
Console.print(name);
Console.println("! Nice to meet you!");
Console.println();
// Ask again for name and clear the old name
Console.println("Hi, what's your name?");
name = ""; // clear the name string
} else { // if the buffer is empty Cosole.read() returns -1
name += c; // append the read char from Console to the name string
}
} else {
delay(100);
}
}*

please response soon?

[Suman kumar Jha]

Hi György Farkas
Will Omega2 will support Arduino YUN official firmware ?

[Suman kumar Jha]

Hi György Farkas
Please response

[György Farkas]

@Suman-kumar-Jha I don't have an Arduino Yún. Sadly I don't know its official firmware. So I don't know that Omega2 is or isn't able to support the official firmware of Arduino Yún.

[Suman kumar Jha]

Thanks for the response, can you tell me if i bring same hardware specification like omega2 then is it possible to port other openwrt firmware ?

Flashing bootloader and firmware everything. I came across Dragino YUN shield. I had checked hardware. Everything is matching. I like omega2 modular design. So i want to stick with this.

Let me show you my project plan.

[Suman kumar Jha]

Hi György Farkas
please reply, guide me i need your help. If other board firmware i can't flash on omega2, then please tell me what configuration i need to do on linux side.

Also as before you said, i had done complete reset of omega2 then on fresh i had installed python full + YUN bridge and connected arduino UNO serial (RX TX). I had tested UART simple communication its working. Omega2 is communicating with arduino dock2 via UART (/dev/ttyS0 -- Arduinno(Serial)). But YUN bridge its not working.

I had read on arduino forum that, when arduino invoke "run-bridge" command through serial, then on linux side python bridge.py should be called which will setup bridge.

I had checked using WinSCP, files exist.

also i had checked some yunbridge files

I am waiting for your reply

[György Farkas]

@Suman-kumar-Jha said in Making Omega2 talks with SAMD21 (Arduino Zero):

Also as before you said, i had done complete reset of omega2 then on fresh i had installed python full + YUN bridge and connected arduino UNO serial (RX TX).

Please let me know what is your hardware test environment now.
Are you try to test the Arduino Bridge software and the yunbridge package with

1. Omega2 on Arduino Dock 2 and a Windows (10?) laptop with Arduino IDE and PuTTY
2. Omega2 and a separate Arduino UNO and a Windows laptop with ...
   In this case: which serial port are you using? How did you connect them exactly?

I had tested UART simple communication its working.

What does it mean exactly?

Omega2 is communicating with arduino dock2 via UART (/dev/ttyS0 -- Arduinno(Serial)).

Are you sure?

But YUN bridge its not working.

Yes.

[Suman kumar Jha]

Yes i am testing Arduino bridge software (Console Read) with yunbridge linux package

and i using Omega2 with Arduino Dock 2 and software (Arduino IDE and Putty) running on windows 10 home

I have seen documentation for Arduino dock 2, hardware serial is connected with omega Uart1 (/dev/ttyS1) . So i planned to understand first what dock is sending message to omega during YUN bridge Init.

Testing procedure

1. UART communication test at High baudrate.

• checked sent data from dock using FTDI RX connected to TX pin of dock

• checked received data on linux by using screen /dev/ttyS1 250000

One more strange thing i found, at High baud-rate (250000, which is the default baudrate of YUN bridge) omega 2 not able receive data. Dock is sending properly. Why?
Please check below snapshot. Where left side is COM93 FTDI UART listener and right is Omega2 SSH

1. UART communication test at LOW baudrate (57600)
   Please check below image, you can see its working good at 57600 baudrate.

1. Then i had set yun bridge baudrate at 57600 by calling

• uci set yunbridge.config.baudrate='57600'
  uci commit yunbridge
  reboot

• After that i had done Simple Yun Bridge test at 57600 baud.
  In this test arduino dock geting stuck on bridge begin itself Dock is sending bridge start command continuously at regular interval and omega2 is not responding. As if its not listening. Even i saw some garbage on screen. I feel garbage was produce by dock itself
  Please check image below

What should i do, please response soon
Thanks

[György Farkas]

@Suman-kumar-Jha
Arduino Dock 2 is not the best test bed for you due to lack of the Serial Monitor on Arduino IDE.

On Arduino Dock 2 the serial connection between the on board Omega2(+) and the on board ATmega328P is hard- wired
(Omega2's UART1/ttyS1 : TX1, RX1, GND to MCU's Rx (D0), Tx (D1), GND respectively via a TXS0108E bidirectional level shifter).

On the serial line the "run-bridge XX100 XX100 ... " (XX100 max 50 times) is not some garbage it's some command - sent by an MCU (Arduino) to an MPU (now it's an Omega2).

uci set yunbridge.config.baudrate='57600' does not change the baudrate of the serial port of the '/sbin/yunbridge' script.

---

BTW what are the outputs of these commands on your test environment (ie. on Omega2):
stty -F /dev/ttyS0 -a
stty -F /dev/ttyS1 -a

[Suman kumar Jha]

Thanks György Farkas for explaining.

Arduino Dock 2 is not the best test bed for you due to lack of the Serial Monitor on Arduino IDE.
Did you mean arduino IDE, where arduino IDE has serial monitor. But actually atmega328p comes with only one hardware serial.
For the above i can use another arduino board multiple hardware serial. So i can assign one of the hardware serial (Serial1) to the Omega UART. What you suggest?

On the serial line the "run-bridge XX100 XX100 ... " (XX100 max 50 times) is not some garbage it's some command

• But on putty screen you can see, there are some unknown symbols also apart from above command. Are these unknows symbols (¢qÿ) are part of commands ?

• By seeing the putty screen and the commands, can i say arduino dock is sending right message for YUN bridge initialization ?

uci set yunbridge.config.baudrate='57600' does not change the baudrate of the serial port of the '/sbin/yunbridge' script
How to set YUN bridge serial port baudrate ? Please explain

BTW what are the outputs of these commands on your test environment (ie. on Omega2):

Which package do i need to install ?

[Suman kumar Jha]

I got it stty package name from another omega community

I had installed stty package, and here is the result

Please guide me what next i should do ?

[György Farkas]

@Suman-kumar-Jha OK Now - after more than 30 posts - we know if you want to test Arduino Bridge between an Arduino and an Omega2(+) then you must install these packages:
python, coreutils-stty and yunbridge.

---

The next step:

I think first of all you should modify the '/sbin/yunbridge' shell script.

#!/bin/sh
stty -F /dev/ttyS0 2500000 clocal cread cs8 -cstopb -parenb
exec < /dev/ttyS0
exec > /dev/ttyS0
exec 2> /dev/ttyS0
askfirst bin/ash --login

There are at least two problems here:

• On Omega2 the Serial Console uses ttyS0 (UART0) - so it's not free.
  On Omega2 ttyS0 (UART0) is occupied by the Serial Console - so it's not free.
  One of the possibilities: use ttyS1 (UART1) instead.

• 2500000 Baud (2,500,000 Baud ie. 2.5 MBaud) is too high for Omega2
  and stty - without some hack - can set only regular Baud rates (eg. ..., 115200, 230400, ...).
  I think 115200 is a good choice for the first test.

So this could be the modified script:

#!/bin/sh
stty -F /dev/ttyS1 115200 clocal cread cs8 -cstopb -parenb
exec < /dev/ttyS1
exec > /dev/ttyS1
exec 2> /dev/ttyS1
askfirst bin/ash --login

or if you want to set the communication speed in the yunbridge config file
with uci set yunbridge.config.baudrate='<BAUDRATE>' then it could be

#!/bin/sh
BAUDRATE=`uci get yunbridge.config.baudrate`
stty -F /dev/ttyS1 ${BAUDRATE} clocal cread cs8 -cstopb -parenb
exec < /dev/ttyS1
exec > /dev/ttyS1
exec 2> /dev/ttyS1
askfirst bin/ash --login

---

Here you are some quick and dirty tests wit the modified '/sbin/yunbridge' script
test bed [Arduino UNO -- level shifters -- Omega2+ on Expansion Dock, FW b299] :

 *** The first "test" ***

# Without Arduino UNO
# Omega2+ on Expansion Dock, FW b299
# FTD232 on Omega2's UART1 lines -- Ubuntu 18.04.2 LTS, picocom

Please press Enter to activate this console.

# Enter pressed manually

BusyBox v1.28.3 () built-in shell (ash)

/bin/ash: can't access tty; job control turned off
   ____       _             ____
  / __ \___  (_)__  ___    / __ \__ _  ___ ___ ____ _
 / /_/ / _ \/ / _ \/ _ \  / /_/ /  ' \/ -_) _ `/ _ `/
 \____/_//_/_/\___/_//_/  \____/_/_/_/\__/\_, /\_,_/
 W H A T  W I L L  Y O U  I N V E N T ?  /___/
 -----------------------------------------------------
   Ω-ware: 0.3.2 b229
 -----------------------------------------------------
root@Omega-5BE1:/#

# So the shell started "well"
# although the *'can't access tty; job control turned off~'* is not a too good message 
 

# *** The second "test" ***

# With Arduino - the *'Console Pixel'* example sketch is running on it
# I watched only Omega2's TX1 line 

Please press Enter to activate this console.
��^C  # this was Omega's reply: 0xEF 0xBF 0xBD 0xEF 0xBF 0xBD 5E 43 0A 0A 0A  . . . . . . ^ C LF LF LF


 
BusyBox v1.28.3 () built-in shell (ash)

bin/ash: can't access tty; job control turned off
   ____       _             ____
  / __ \___  (_)__  ___    / __ \__ _  ___ ___ ____ _
 / /_/ / _ \/ / _ \/ _ \  / /_/ /  ' \/ -_) _ `/ _ `/
 \____/_//_/_/\___/_//_/  \____/_/_/_/\__/\_, /\_,_/
 W H A T  W I L L  Y O U  I N V E N T ?  /___/
 -----------------------------------------------------
   Ω-ware: 0.3.2 b229
 -----------------------------------------------------
root@Omega-5BE1:/# 
root@Omega-5BE1:/# �V�  # Omega's reply: 0xEF 0xBF 0xBD 56 0xEF 0xBF 0xBD 0A 0A 0A  . . . V . . . LF LF LF

It seems the two devices can communicate with each other via the Arduino Bridge
but something is not perfect yet because the LED is not blinking.
See also the Console Pixel example sketch.

You could repeat these tests also on your Arduino Dock 2.

[Suman kumar Jha]

@György-Farkas said in Making Omega2 talks with SAMD21 (Arduino Zero):

dirty tests wit the modified '/sbin/yunbridge' script

Thanks, i had done everything as you said. Now can you please send yunbridge script. So i can also perform bridge test on my test bed

[György Farkas]

@Suman-kumar-Jha said in Making Omega2 talks with SAMD21 (Arduino Zero):

Now can you please send yunbridge script.

What are you talking about please?

[Suman kumar Jha]

I requested you for sending me script file what you used to test yunbridge on your test bed.
I also had setup same test bed, but i don't have script to test.

In /sbin/yunbridge i found only yun bridge settings.
So kindly send your Yun bridge test script.

[György Farkas]

@Suman-kumar-Jha There is no more file - only the modified '/sbin/yunbridge'. It's a shell script that starts a serial console during Omega's init - independently from the Arduino.

[Suman kumar Jha]

Ok i got it, what modification required can you tell in yunbridge script file.

This is the script i am having now, what modification needed

*#!/bin/sh

BAUDRATE=uci get yunbridge.config.baudrate
[ -n "${BAUDRATE}" ] || BAUDRATE=250000

[ -e /lib/ramips.sh -a ${BAUDRATE} = 250000 ] && BAUDRATE=2500000

stty -F /dev/ttyS1 ${BAUDRATE} clocal cread cs8 -cstopb -parenb
exec < /dev/ttyS1
exec > /dev/ttyS1
exec 2> /dev/ttyS1
askfirst bin/ash --login*