Please help!! my omega 2 now boot looping not working...
-
Here is my terminal log anyone resolve this problem?
/ __ ___ ()__ ___ / __ _ _ ___ ___ ____ _
/ // / _ / / _ / _ \ / // / ' / -) _/ _/
_/////___//// _////_/_, /_,/
W H A T W I L L Y O U I N V E N T ? /__/"Board: Onion Omega2 APSoC DRAM: 64 MB
relocate_code Pointer at: 83f60000
Software System Reset Occurred
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment============================================
Onion Omega2 UBoot Version: 4.3.0.3ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Oct 18 2016 Time:17:30:55icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
CPU freq = 575 MHZ
Estimated memory size = 64 Mbytes
Resetting MT7628 PHY.
Initializing MT7688 GPIO system.
- Hold Reset button for more options *
Boot Linux from Flash NO RESET PRESSED.
Booting image at bc050000 ...
Image Name: MIPS LEDE Linux-4.4.42
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1306446 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrdTransferring control to Linux (at address 80000000) ...
Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.4.42 (root@2272a3272872) (gcc version 5.4.0 (LED
E GCC 5.4.0 r3009-968fa53) ) #0 Mon Jan 16 19:40:14 2017
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Onion Omega2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 by
tes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa
ges: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jf
fs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007a790
[ 0.000000] Readback ErrCtl register=0007a790
[ 0.000000] Memory: 60580K/65536K available (3012K kernel code, 143K rwdata,
724K rodata, 208K init, 196K bss, 4956K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] intc: using register map from devicetree
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource_probe: no matching clocksources found
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_
idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405
115902ns
[ 0.007522] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.070038] pid_max: default: 32768 minimum: 301
[ 0.074637] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080975] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094288] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, m
ax_idle_ns: 19112604462750000 ns
[ 0.103931] pinctrl core: initialized pinctrl subsystem
[ 0.109668] NET: Registered protocol family 16
[ 0.133174] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.138709] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.144140] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.150649] i2c-mt7621 10000900.i2c: clock 100KHz, re-start not support
[ 0.158170] clocksource: Switched to clocksource MIPS
[ 0.164527] NET: Registered protocol family 2
[ 0.169629] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.176322] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.182504] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.188703] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.194304] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.200647] NET: Registered protocol family 1
[ 0.210322] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.216271] Crashlog allocated RAM at address 0x3f00000
[ 0.236576] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.242228] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI
TY) (c) 2001-2006 Red Hat, Inc.
[ 0.254360] io scheduler noop registered
[ 0.258101] io scheduler deadline registered (default)
[ 0.263968] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; ca
nnot claim for 10005000.pwm
[ 0.273049] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[ 0.279058] rt2880-pinmux pinctrl: could not request pin 18 (io18) from grou
p pwm0 on device rt2880-pinmux
[ 0.288461] mtk-pwm 10005000.pwm: Error applying setting, reverse things bac
k
[ 0.295801] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.303367] console [ttyS0] disabled
[ 0.306799] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud
= 2500000) is a 16550A
[ 0.315580] console [ttyS0] enabled
[ 0.315580] console [ttyS0] enabled
[ 0.322573] bootconsole [early0] disabled
[ 0.322573] bootconsole [early0] disabled
[ 0.331250] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud =
2500000) is a 16550A
[ 0.340745] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud =
2500000) is a 16550A
[ 0.351312] spi-mt7621 10000b00.spi: sys_freq: 193333333
[ 0.361331] m25p80 spi32766.0: using chunked io (size=31)
[ 0.366820] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[ 0.372034] 4 ofpart partitions found on MTD device spi32766.0
[ 0.377945] Creating 4 MTD partitions on "spi32766.0":
[ 0.383176] 0x000000000000-0x000000030000 : "u-boot"
[ 0.389985] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.397207] 0x000000040000-0x000000050000 : "factory"
[ 0.404224] 0x000000050000-0x000001000000 : "firmware"
[ 0.431595] 2 uimage-fw partitions found on MTD device firmware
[ 0.437621] 0x000000050000-0x00000018ef8e : "kernel"
[ 0.444317] 0x00000018ef8e-0x000001000000 : "rootfs"
[ 0.451254] mtd: device 5 (rootfs) set to be root filesystem
[ 0.457065] 1 squashfs-split partitions found on MTD device rootfs
[ 0.463405] 0x0000006e0000-0x000001000000 : "rootfs_data"
[ 0.480587] rt3050-esw 10110000.esw: link changed 0x00
[ 0.488295] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb
0100000, irq 5
[ 0.496902] i2c /dev entries driver
[ 0.501075] mt7621_wdt 10000120.watchdog: Initialized
[ 0.507722] NET: Registered protocol family 10
[ 0.516240] NET: Registered protocol family 17
[ 0.520916] bridge: automatic filtering via arp/ip/ip6tables has been deprec
ated. Update your scripts to load br_netfilter if you need this.
[ 0.533731] 8021q: 802.1Q VLAN Support v1.8
[ 0.545073] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.553439] Freeing unused kernel memory: 208K (803cc000 - 80400000)
[ 1.573034] init: Console is alive
[ 1.576710] init: - watchdog -
[ 4.085408] usbcore: registered new interface driver usbfs
[ 4.091154] usbcore: registered new interface driver hub
[ 4.096636] usbcore: registered new device driver usb
[ 4.107993] exFAT: Version 1.2.9
[ 4.151324] SCSI subsystem initialized
[ 4.161738] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.170058] ehci-platform: EHCI generic platform driver
[ 4.185705] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
[ 4.192520] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[ 4.197847] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.203720] ehci-platform 101c0000.ehci: new USB bus registered, assigned bu
s number 1
[ 4.211885] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.238213] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.245662] hub 1-0:1.0: USB hub found
[ 4.249900] hub 1-0:1.0: 1 port detected
[ 4.258609] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.266457] ohci-platform: OHCI generic platform driver
[ 4.272099] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 4.279075] ohci-platform 101c1000.ohci: new USB bus registered, assigned bu
s number 2
[ 4.287182] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.353306] hub 2-0:1.0: USB hub found
[ 4.357546] hub 2-0:1.0: 1 port detected
[ 4.374347] MTK MSDC device init.
[ 4.418340] mtk-sd: MediaTek MT6575 MSDC Driver
[ 4.426292] sdhci: Secure Digital Host Controller Interface driver
[ 4.432639] sdhci: Copyright(c) Pierre Ossman
[ 4.438573] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.448930] usbcore: registered new interface driver usb-storage
[ 4.465497] init: - preinit -
[ 5.244330] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug[ 5.45
2505] random: procd: uninitialized urandom read (4 bytes read, 9 bits of entrop
y available)
level
[ 8.600263] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 8.616320] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.701583] procd: - early -
[ 8.704612] procd: - watchdog -
[ 9.354267] procd: - ubus -
[ 9.558316] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.567946] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.577237] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.586813] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.596061] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.605418] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.614814] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits
of entropy available)
[ 9.624384] procd: - init -
Please press Enter to activate this console.
[ 10.089234] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 10.156230] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.179463] Ralink/MTK WiFi EEPROM API Build for MT7620.
[ 10.221936] WRTnode AP Driver version: 4.1.0.0
[ 10.294781] Linux video capture interface: v2.00
[ 10.599658] hidraw: raw HID events driver (C) Jiri Kosina
[ 10.657687] Bluetooth: Core ver 2.21
[ 10.661504] NET: Registered protocol family 31
[ 10.666011] Bluetooth: HCI device and connection manager initialized
[ 10.672489] Bluetooth: HCI socket layer initialized
[ 10.677441] Bluetooth: L2CAP socket layer initialized
[ 10.682600] Bluetooth: SCO socket layer initialized
[ 10.691723] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 10.697123] Bluetooth: BNEP filters: protocol multicast
[ 10.702504] Bluetooth: BNEP socket layer initialized
[ 10.714209] usbcore: registered new interface driver btusb
[ 10.723774] usbcore: registered new interface driver cdc_acm
[ 10.729595] cdc_acm: USB Abstract Control Model driver for USB modems and IS
DN adapters
[ 10.741489] Bluetooth: HCI UART driver ver 2.3
[ 10.746012] Bluetooth: HCI UART protocol H4 registered
[ 10.751284] Bluetooth: HCI UART protocol BCSP registered
[ 10.760853] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 10.766884] Bluetooth: HIDP socket layer initialized
[ 10.775044] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.796165] nf_conntrack version 0.5.0 (949 buckets, 3796 max)
[ 10.825786] Bluetooth: RFCOMM TTY layer initialized
[ 10.830831] Bluetooth: RFCOMM socket layer initialized
[ 10.836065] Bluetooth: RFCOMM ver 1.11
[ 10.847677] spidev spi32766.1: buggy DT: spidev listed directly in DT
[ 10.854293] ------------[ cut here ]------------
[ 10.859009] WARNING: CPU: 0 PID: 473 at drivers/spi/spidev.c:720 0x82c8e33c(
)
[ 10.866238] Modules linked in: spidev(+) snd_usbmidi_lib slhc rfcomm nf_reje
ct_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv
6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filte
r ip_tables hidp hid_generic hci_uart crc_ccitt cdc_acm btusb btintel bnep blue
tooth snd_soc_simple_card snd_soc_ralink_i2s snd_soc_wm8960 videobuf2_vmalloc v
ideobuf2_memops videobuf2_core hid v4l2_common videodev evdev snd_soc_core rali
nk_gdma virt_dma mt76x8 ralink_eeprom_api ledtrig_oneshot ledtrig_morse ledtrig
heartbeat ledtrig_gpio ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip
6table_mangle ip6table_filter ip6_tables x_tables msdos snd_pcm_dmaengine snd_c
ompress snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device
snd_hwdep snd input_core soundcore vfat fat ntfs configfs autofs4 nls_utf8 nls
iso8859_1 nls_cp437 regmap_i2c dma_shared_buffer ecb cmac mmc_block usb_storage
sdhci_pltfm sdhci mtk_sd mmc_core leds_gpio ohci_platform ohci_hcd ledtrig_tra
nsient ehci_platform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbc
ache exfat usbcore nls_base usb_common crc16 cryptomgr aead crypto_null crc32c_
generic crypto_hash
[ 10.973149] CPU: 0 PID: 473 Comm: kmodloader Not tainted 4.4.42 #0
[ 10.979424] Stack : 803680f4 00000000 00000001 803b0000 839216a4 803b0d83 80
349a58 000001d9
80403438 0000000b 0000001a 024000c0 800661d4 8004adf4 8034ef54 803b00
00
00000003 0000000b 8034d358 83053b4c 800661d4 80048d60 00000000 000000
00
00000001 00000000 00000000 00000000 00000000 00000000 00000000 000000
00
00000000 00000000 00000000 00000000 00000000 00000000 00000000 000000
00
...
[ 11.015581] Call Trace:
[ 11.018118] [<800661d4>] module_sect_show+0x0/0x18
[ 11.023001] [<8004adf4>] vprintk_default+0x24/0x30
[ 11.027876] [<800661d4>] module_sect_show+0x0/0x18
[ 11.032751] [<80048d60>] printk+0x2c/0x38
[ 11.036834] [<800253fc>] warn_slowpath_common+0xa0/0xd0
[ 11.042156] [<801499f0>] dump_stack+0x14/0x28
[ 11.046575] [<80014874>] show_stack+0x50/0x84
[ 11.051013] [<800253fc>] warn_slowpath_common+0xa0/0xd0
[ 11.056316] [<82c8e33c>] 0x82c8e33c
[ 11.059868] [<82c90000>] 0x82c90000
[ 11.063419] [<800254b4>] warn_slowpath_null+0x18/0x24
[ 11.068567] [<801f6670>] of_match_node+0x20/0x44
[ 11.073263] [<82c90000>] 0x82c90000
[ 11.076802] [<82c8e33c>] 0x82c8e33c
[ 11.080367] [<801bbde8>] devm_kfree+0x20/0x44
[ 11.084820] [<801dd02c>] spi_drv_probe+0x3c/0x84
[ 11.089530] [<801b8918>] driver_probe_device+0x120/0x288
[ 11.094937] [<8008a0e8>] kstrdup+0x44/0x8c
[ 11.099124] [<801dcf2c>] spi_match_device+0x38/0xa8
[ 11.104090] [<801b8afc>] __driver_attach+0x7c/0xb4
[ 11.108983] [<801b6d20>] next_device+0x10/0x30
[ 11.113500] [<801b8a80>] __driver_attach+0x0/0xb4
[ 11.118292] [<801b6ddc>] bus_for_each_dev+0x9c/0xac
[ 11.123266] [<802ed4f4>] klist_add_tail+0x24/0x50
[ 11.128038] [<82c90000>] 0x82c90000
[ 11.131597] [<801b6bb0>] bus_get+0x2c/0x50
[ 11.135782] [<801b8010>] bus_add_driver+0xec/0x20c
[ 11.140661] [<800acc64>] exact_match+0x0/0x8
[ 11.144993] [<800ad16c>] exact_lock+0x0/0x24
[ 11.149337] [<82c90000>] 0x82c90000
[ 11.152873] [<82c90000>] 0x82c90000
[ 11.156414] [<801b9214>] driver_register+0xa8/0xf8
[ 11.161291] [<832fc000>] init_module+0x0/0xdc [spidev]
[ 11.166514] [<82c90000>] 0x82c90000
[ 11.170070] [<82c90000>] 0x82c90000
[ 11.173607] [<82c90000>] 0x82c90000
[ 11.177149] [<832fc098>] init_module+0x98/0xdc [spidev]
[ 11.182469] [<801555c0>] kasprintf+0x1c/0x28
[ 11.186817] [<8004574c>] __wake_up+0x24/0x48
[ 11.191167] [<832fc000>] init_module+0x0/0xdc [spidev]
[ 11.196402] [<8000d890>] do_one_initcall+0x1e8/0x214
[ 11.201470] [<8004574c>] __wake_up+0x24/0x48
[ 11.205804] [<832fc000>] init_module+0x0/0xdc [spidev]
[ 11.211050] [<80034404>] call_usermodehelper_exec+0x144/0x160
[ 11.216894] [<80033ef4>] call_usermodehelper_setup+0x38/0xa8
[ 11.222673] [<800661d4>] module_sect_show+0x0/0x18
[ 11.227554] [<800673f4>] do_init_module+0x74/0x1cc
[ 11.232441] [<8009dc18>] __vunmap+0xf0/0x114
[ 11.236806] [<80068c88>] load_module+0x16c0/0x1b68
[ 11.241689] [<800667c0>] unknown_module_param_cb+0x0/0xac
[ 11.247171] [<8009e10c>] __vmalloc_node+0x34/0x40
[ 11.251980] [<800691c4>] SyS_init_module+0x94/0x180
[ 11.256933] [<80069260>] SyS_init_module+0x130/0x180
[ 11.262012] [<8000682c>] syscall_common+0x30/0x54
[ 11.266791] [<80008c58>] __bzero+0xbc/0x164
[ 11.271044]
[ 11.272557] ---[ end trace 29af544c9ae6cae3 ]---
[ 11.284526] usbcore: registered new interface driver ums-alauda
[ 11.293593] usbcore: registered new interface driver ums-cypress
[ 11.302753] usbcore: registered new interface driver ums-datafab
[ 11.311630] usbcore: registered new interface driver ums-freecom
[ 11.320722] usbcore: registered new interface driver ums-isd200
[ 11.329867] usbcore: registered new interface driver ums-jumpshot
[ 11.338882] usbcore: registered new interface driver ums-karma
[ 11.348592] usbcore: registered new interface driver ums-sddr09
[ 11.357563] usbcore: registered new interface driver ums-sddr55
[ 11.366971] usbcore: registered new interface driver ums-usbat
[ 11.379162] usbcore: registered new interface driver usbhid
[ 11.384824] usbhid: USB HID core driver
[ 11.392464] usbcore: registered new interface driver usblp
[ 11.406347] usbcore: registered new interface driver usbserial
[ 11.412476] usbcore: registered new interface driver usbserial_generic
[ 11.419248] usbserial: USB Serial support registered for generic
[ 11.437693] Driver for 1-wire Dallas network protocol.
[ 11.463666] xt_time: kernel timezone is -0000
[ 11.470419] usbcore: registered new interface driver ch341
[ 11.476104] usbserial: USB Serial support registered for ch341-uart
[ 11.484872] usbcore: registered new interface driver cp210x
[ 11.490740] usbserial: USB Serial support registered for cp210x
[ 11.500261] usbcore: registered new interface driver ftdi_sio
[ 11.506207] usbserial: USB Serial support registered for FTDI USB Serial Dev
ice
[ 11.528071] usbcore: registered new interface driver pl2303
[ 11.533941] usbserial: USB Serial support registered for pl2303
[ 11.545362] PPP generic driver version 2.4.2
[ 11.552983] NET: Registered protocol family 24
[ 11.570961] usbcore: registered new interface driver snd-usb-audio
[ 11.588009] usbcore: registered new interface driver uvcvideo
[ 11.593915] USB Video Class driver (1.1.1)
[ 11.841859] random: jshn: uninitialized urandom read (4 bytes read, 20 bits
of entropy available)
[ 12.008653] random: jshn: uninitialized urandom read (4 bytes read, 20 bits
of entropy available)
[ 18.640914] EEPROM:Read from [factory] offset 0x0,length 0x400.
[ 21.978237] ch1 bssid=9c:7d:a3:6d:79:14
[ 21.982296] ch1 bssid=20:76:93:3b:60:d0
[ 21.986295] ch1 bssid=2c:30:33:57:e4:ed
[ 21.990305] ch1 bssid=20:6b:e7:ba:07:c0
[ 21.994309] ch4 bssid=0c:57:00:61:97:54
[ 21.998309] ch4 bssid=08:57:00:61:97:54
[ 22.002289] ch6 bssid=00:25:86:56:93:0c
[ 22.006267] ch6 bssid=a0:91:c8:8d:30:01
[ 22.010284] ch6 bssid=88:25:93:9c:56:3f
[ 22.014288] ch7 bssid=64:13:6c:4c:f4:0c
[ 22.018287] ch8 bssid=48:a7:4e:40:00:a8
[ 22.022266] ch11 bssid=08:10:79:84:09:b0
[ 22.026335] ch11 bssid=b0:95:8e:c4:4c:99
[ 22.030422] ch11 bssid=20:6b:e7:24:72:18
[ 22.034490] ch11 bssid=32:6b:e7:24:72:18
[ 22.038564] =====================================================
[ 22.044747] Channel 1 : Dirty = 348, False CCA = 0, Busy Time = 8200, Skip C
hannel = FALSE
[ 22.053139] Channel 2 : Dirty = 244, False CCA = 0, Busy Time = 5413, Skip C
hannel = FALSE
[ 22.061529] Channel 3 : Dirty = 268, False CCA = 0, Busy Time = 1525, Skip C
hannel = FALSE
[ 22.069922] Channel 4 : Dirty = 364, False CCA = 0, Busy Time = 3746, Skip C
hannel = FALSE
[ 22.078315] Channel 5 : Dirty = 292, False CCA = 0, Busy Time = 4071, Skip C
hannel = FALSE
[ 22.086693] Channel 6 : Dirty = 326, False CCA = 0, Busy Time = 6855, Skip C
hannel = FALSE
[ 22.095086] Channel 7 : Dirty = 336, False CCA = 0, Busy Time = 4315, Skip C
hannel = FALSE
[ 22.103473] Channel 8 : Dirty = 322, False CCA = 0, Busy Time = 6565, Skip C
hannel = FALSE
[ 22.111865] Channel 9 : Dirty = 244, False CCA = 0, Busy Time = 3656, Skip C
hannel = FALSE
[ 22.120258] Channel 10 : Dirty = 240, False CCA = 0, Busy Time = 7148, Skip
Channel = FALSE
[ 22.128739] Channel 11 : Dirty = 334, False CCA = 0, Busy Time = 6871, Skip
Channel = FALSE
[ 22.137199] =====================================================
[ 22.143389] Rule 1 CCA value : Min Dirtiness (Include extension channel) ==>
Select Channel 10
[ 22.152217] Min Dirty = 240
[ 22.155047] ExChannel = 0 , 0
[ 22.158051] BW = 20
[ 22.630009] device eth0.1 entered promiscuous mode
[ 22.634887] device eth0 entered promiscuous mode
[ 22.676883] br-wlan: port 1(eth0.1) entered forwarding state
[ 22.682751] br-wlan: port 1(eth0.1) entered forwarding state
[ 24.678256] br-wlan: port 1(eth0.1) entered forwarding state
[ 26.939710] Kernel panic - not syncing: stack-protector: Kernel stack is cor
rupted in: 8331d944
[ 26.939710]
[ 26.953511] Rebooting in 3 seconds..
-
Did you change anything substantial before your last boot? Is this your first boot? And it's in a loop where the panic happens, it reboots, and panic happens again?
If you don't have many things saved/installed you can factory reset (hold reset button for 5 seconds) and it should be good to go.
-
@HUN-LEE
Please read this topic Omega2+ Not working out of box! (and its forerunner).ps.
If you want a nicer (ie. can read more easily) text please edit your post.
Put a line with```(three backticks) before and put a line with```(three backticks) after your terminal log.