ws2818 led strip have the function break-point continue which same with the ws2813,also,is 4 weld pad,so,it can replace the ws2811 or ucs1903, but i want to know more the ic parameter diffence between ws2818 with the ws2811,ws2818 ic signal transmission speed is more faster or others difference?appreciated your help!
PCS WS2813 6Pins 5050 RGB DC5V
WS2813 is a set of control circuit and light-emitting circuit in one of the intelligent external control LED light source. Its appearance and a 5050LED lamp beads the same, each component is a pixel. Pixel interior contains intelligent digital interface data latching signal shaping amplification drive circuit, anti-reverse circuit, also includes high-precision internal oscillator and high precision constant current control module, effectively ensuring the pixel point light color consistent. Has a unique breakpoint transfer function, to achieve two-way signal transmission, a single pixel in the case of damage, does not affect the overall color display. Data protocol using single-line zero-code communication, pixel reset after power-on, DIN-side receiver from the controller to transfer data from the first sent over the 24bit data is the first pixel after extraction, sent to the pixels inside Of the data latch, the rest of the data through the internal shaping circuit shaping after amplification through the DO port forwards the output to the next cascade of pixels, each passing through a pixel, the signal is reduced by 24bit. Pixels using automatic shaping forwarding technology, making the number of cascade of the pixel from the signal transmission limit, only limited signal transmission speed requirements. BIN end receives the data signal swallowed 24bit data, and DIN data comparison, if the DIN terminal no signal, BIN side has received the signal, switch to the BIN terminal to receive input signals to ensure that one of the IC damage will not affect the signal level The control IC remains in the BIN port to receive the state, until the next power-off after re-confirmed. Up to 2KHZ port scan frequency, capture in the high-definition camera will not flicker phenomenon, is ideal for high-speed mobile products. 250us or more of the RESET time, an interrupt will not cause a false reset, you can support a lower frequency, cheap MCU. WS2813 provides 15mA and 5mA two current versions, each version provides high-brightness version and cost-effective version, a total of 4 specifications.
6 feet built-in IC lamp beads Features:
Intelligent reverse polarity protection, reverse power supply will not damage the IC.
IC control circuit and LED point light source common a power supply.
Control circuit and RGB chip integrated in a 5050 package components, constitute a complete external control pixel.
Built-in signal shaping circuit, any one pixel after receiving the signal waveform shaping and then output to ensure that the line waveform distortion will not be accumulated.
Built-in power-on reset and power-down reset circuit.
Each pixel of the three primary colors can achieve 256 levels of brightness display, complete 16,777,216 colors of the true color display, scanning frequency of not less than 400Hz / s.
Serial cascade interface, through a signal line to complete the data reception and decoding.
Any two-point transmission distance of not more than 5 meters without adding any circuit.
When the refresh rate of 30 frames / sec, the cascade number is not less than 1024 points.
Data transmission speed up to 800Kbps.
The color of light is highly consistent and cost-effective.
WS2815 by three Ann (RGB) 5050+ Ming for chip drive IC positiveness integrated single serial constant current IC-LED,unlimited cascade, built-in power supply, reverse connect protection template power reverse will not damage
the IC, the history of the most stable LED RGB built-in IC-5050. Article is suitable for the magic lantern, balance the light belt,audio module, LED electronic screen and other LED products.
1,Model :WS2815
2,Brand:witop
3,Product specification:SMD 5050RGB
4,Operating voltage:DC 12V
5,Product Chip:Sanan
6,Drive IC:ws2815 IC
7,Product power:0.25W
8,Service life:50000H
9,Gray level:256 levels,“256256256=16777216” full-color display, and the refresh frequency reaches to 2KHz/s.
10, Dual-signal wires version, signal break-point continuous transmission.
11, Any two point the distance more than 3m transmission signal without any increase circuit.
12, When the refresh rate is 30fps, cascade numbers are far more than 1024 points.
13,Data transmitting at speeds of up to 800Kbps.
14, Good color consistency reliability, high cost-effective.
ws2815 addressable 12v led strip,it is also have the function of breakpoint contine.how can i use the arduino controller to controll it? and it can make 10 meters?
it is a new led in the market? very intersted. I think apa102c and sk9822 is better. because,it is double signal transmission. we supply the apa10c and sk9822 addressable led strip,no matter what led broken,it can work normally.
we have breakpoint continue ws2813 full color led strip which more reliable.Email:ch1204665648@hotmail.com
many led strip can remote control, and use the controllor.
and we have a new product gs1820, it no need controllor, comes with more than 30 kinds of color inside of the led.
hope that led can help you.