That is what I though but bring to run the "oupgrade" command and it says I am not connected
Restarting wifimanager for changes to take effect
root@Omega-690B:~# oupgrade
Device Firmware Version: 0.1.5 b130
Checking latest version online...
ERROR: Could not connect to Onion Firmware Server! Check your internet connection and try again!
root@Omega-690B:~#
I get to the last line and get nothing. I do really appreciate your help, you have been very responsive and I appreciate that very much.
Carls-MBP:~ carlstevens$ ssh root@omega-690B.local
ssh: Could not resolve hostname omega-690b.local: nodename nor servname provided, or not known
Carls-MBP:~ carlstevens$ ssh root@omega-690B.local
root@omega-690b.local's password:
BusyBox v1.25.1 () built-in shell (ash)
/ _ /root@Omega-690B:~# wifisetup
Onion Omega Wifi Setup
Select from the following:
Selection: 1
Scanning for wifi networks...
Select Wifi network:
Selection: 2
Network: MilwaukeeMaker2GHz
Authentication type: WPA2PSK
Enter password: wrenchiron
Restarting wifimanager for changes to take effect
root@Omega-690B:~#
Correct once I get to the step where I am entering the wifi password it sits idle for 10 or more minutes and then I get a "broken pipe" error.
Correct tried using the wizard first then moved on to ssh like the bottom of your wizard set up suggests if that did not work then on to connecting via serial. is there a way to set it up link a PI by coping a file system to the SD card?
Not trying to be a pain here but if the 3 methods for setting up wifi on your website don't work and you need to have a certain set of skills to use the board that statements like this on your crowd funding site don't make sense.
"With the Omega2, we want to lower the barrier of entry, and allow everyone to take the leap into hardware development."
Just tried using serial.
[ 636.531070] ch1 bssid=00:15:6d:ee:2f:52
[ 636.535070] ch1 bssid=4c:5e:0c:14:4a:57
[ 636.539106] ch11 bssid=06:18:0a:df:60:c0
[ 636.543206] ch11 bssid=5e:cf:7f:12:35:11
[ 636.547274] ch11 bssid=5e:cf:7f:0f:17:56
[ 636.551360] ch11 bssid=00:18:0a:df:60:c0
[ 636.555421] =====================================================
[ 636.561623] Channel 1 : Dirty = 150, False CCA = 0, Busy Time = 3715, Skip Channel = FALSE
[ 636.570000] Channel 2 : Dirty = 64, False CCA = 0, Busy Time = 2073, Skip Channel = FALSE
[ 636.578312] Channel 3 : Dirty = 56, False CCA = 0, Busy Time = 1107, Skip Channel = FALSE
[ 636.586620] Channel 4 : Dirty = 48, False CCA = 0, Busy Time = 1024, Skip Channel = FALSE
[ 636.594936] Channel 5 : Dirty = 40, False CCA = 0, Busy Time = 179, Skip Channel = FALSE
[ 636.603151] Channel 6 : Dirty = 0, False CCA = 0, Busy Time = 94, Skip Channel = FALSE
[ 636.611196] Channel 7 : Dirty = 80, False CCA = 0, Busy Time = 85, Skip Channel = FALSE
[ 636.619310] Channel 8 : Dirty = 96, False CCA = 0, Busy Time = 138, Skip Channel = FALSE
[ 636.627530] Channel 9 : Dirty = 112, False CCA = 0, Busy Time = 1946, Skip Channel = FALSE
[ 636.635927] Channel 10 : Dirty = 128, False CCA = 0, Busy Time = 1164, Skip Channel = FALSE
[ 636.644411] Channel 11 : Dirty = 300, False CCA = 0, Busy Time = 2353, Skip Channel = FALSE
[ 636.652880] =====================================================
[ 636.659057] Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 6
[ 636.667799] Min Dirty = 0
[ 636.670453] ExChannel = 0 , 0
[ 636.673465] BW = 20
[ 637.022125] br-wlan: port 2(ra0) entered forwarding state
[ 637.027667] br-wlan: port 2(ra0) entered forwarding state
[ 639.021112] br-wlan: port 2(ra0) entered forwarding state
[ 660.534309] br-wlan: port 2(ra0) entered disabled state
[ 661.761136] EEPROM:Read from [factory] offset 0x0,length 0x400.
[ 664.191099] ch1 bssid=00:15:6d:ee:2f:52
[ 664.195099] ch1 bssid=4c:5e:0c:14:4a:57
[ 664.199079] ch6 bssid=50:3d:e5:30:ed:95
[ 664.203086] ch11 bssid=06:18:0a:df:60:c0
[ 664.207153] ch11 bssid=00:18:0a:df:60:c0
[ 664.211237] ch11 bssid=5e:cf:7f:0f:17:56
[ 664.215300] =====================================================
[ 664.221499] Channel 1 : Dirty = 150, False CCA = 0, Busy Time = 1897, Skip Channel = FALSE
[ 664.229876] Channel 2 : Dirty = 84, False CCA = 0, Busy Time = 1223, Skip Channel = FALSE
[ 664.238193] Channel 3 : Dirty = 80, False CCA = 0, Busy Time = 1294, Skip Channel = FALSE
[ 664.246502] Channel 4 : Dirty = 76, False CCA = 0, Busy Time = 1649, Skip Channel = FALSE
[ 664.254808] Channel 5 : Dirty = 72, False CCA = 0, Busy Time = 278, Skip Channel = FALSE
[ 664.263019] Channel 6 : Dirty = 70, False CCA = 0, Busy Time = 1295, Skip Channel = FALSE
[ 664.271325] Channel 7 : Dirty = 92, False CCA = 0, Busy Time = 3054, Skip Channel = FALSE
[ 664.279615] Channel 8 : Dirty = 100, False CCA = 0, Busy Time = 178, Skip Channel = FALSE
[ 664.287921] Channel 9 : Dirty = 108, False CCA = 0, Busy Time = 1994, Skip Channel = FALSE
[ 664.296314] Channel 10 : Dirty = 116, False CCA = 0, Busy Time = 2527, Skip Channel = FALSE
[ 664.304796] Channel 11 : Dirty = 230, False CCA = 0, Busy Time = 2756, Skip Channel = FALSE
[ 664.313266] =====================================================
[ 664.319442] Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 6
[ 664.328182] Min Dirty = 70
[ 664.330924] ExChannel = 0 , 0
[ 664.333936] BW = 20
[ 664.682148] br-wlan: port 2(ra0) entered forwarding state
[ 664.687689] br-wlan: port 2(ra0) entered forwarding state
[ 666.681092] br-wlan: port 2(ra0) entered forwarding state
root@Omega-690B:/# oupgrade
Device Firmware Version: 0.1.5 b130
Checking latest version online...
ERROR: Could not connect to Onion Firmware Server! Check your internet connection and try again!
Is there a way to sent this board back and get one that works...
@WereCatf I am new to the command line sorry. once I SSH into the device how to I get to there?
@WereCatf I'm sorry if this is a stupid question. Is this text you are entering in the command line? Where do I put this text?