Posts made by Christiaan Scholtz

Hi can I read from one usb port while writing to the other (mini) one whilst simultaneously drawing power form it?

Great work. Can I have the source for the interrupt lib? Or at least a pointer to the docs you used to make it. I don't want to link it I want to integrate to my own thing.

fyi I had the same problem on a fresh install of ubuntu 14, no USB devices listed. But after some time when i tried again it simply worked by itself.

Ah I've fixed it. There were left over settings from the previous image, I had changed the name of the interface in etc/config/network so the 'ubus call network.interface.wwan status' line in wifisetup was failing because it wasn't called wwan.

Hi Boken

Which missing command might the script be trying to run just after wlan becomes ready?

The router is connected to the internet and I was able to connect to it and to the net with the previous image.
Even if I abort early it seems like no IP is assigned.

config wifi-iface
        option device 'radio0'
        option mode 'sta'
        option network 'wwan'
        option ssid 'wireless'
        option encryption 'psk2'
        option key 'xxxxxxxxx'

#ifconfig
wlan0     Link encap:Ethernet  HWaddr 00:23:CD:05:01:04
          inet6 addr: fe80::223:cdff:fe05:104/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:334 (334.0 B)  TX bytes:5150 (5.0 KiB)

I have a new problem I cant seem to connect to the wireless. I disabled authentication, but still get the command not found error.

Select from the following:

1. Scan for Wifi networks
2. Type network info
   q) Exit

Selection: 1
Scanning for wifi networks...

Select Wifi network:

1. wireless
2. NETGEAR

Selection: 1
Network: wireless
Authentication type: none

Connecting to wireless network using intf 1...
[ 1333.320000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 1333.560000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1334.440000] wlan0: authenticate with c8:6c:87:f1:fc:44
[ 1334.460000] wlan0: send auth to c8:6c:87:f1:fc:44 (try 1/3)
[ 1334.470000] wlan0: authenticated
[ 1334.480000] wlan0: associate with c8:6c:87:f1:fc:44 (try 1/3)
[ 1334.480000] wlan0: RX AssocResp from c8:6c:87:f1:fc:44 (capab=0x401 status=0 aid=2)
[ 1334.490000] wlan0: associated
[ 1334.490000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1334.520000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
Command failed: Not found
Failed to parse message data
sh: 1: unknown operand
Checking wwan device status...
wwan is sh: 1: unknown operand
not up!!
Checking internet connection...
ERROR: request timeout, internet connection not successful
Disabling network on iface 1 ...
Done!
root@Omega-0103:/# [ 1370.060000] wlan0: deauthenticating from c8:6c:87:f1:fc:44 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 1372.760000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1372.820000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

That worked, thank you very much

I tried it without 'keep current settings' as well to no avail.

Should I try building that Ethernet thing?

I think I have the 'test' image reported by some people. I tried to flash with omega-v0.0.4-b229.bin using flash new image webpage at 192.168.3.1 but it says 'The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. '

I really don't want to send the chip back isn't there anything I can do here to get the new image on?