I power the board without using the dock (given power from arduino uno board 3.3v) but the omega 2+ amber light turns on. Then after about 10 seconds the light starts to blink, and does not turn solid.
So I did a serial connection. When I start the device this is what I get. At the end it stay at EEPROM : read line.
# code block
____ _ ____
/ __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _
/ /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/
\____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/
W H A T W I L L Y O U I N V E N T ? /___/" .
Board: Onion Omega2 APSoC DRAM: 128 MB
relocate_code Pointer at: 87f60000
flash manufacture id: c2, device id 20 19
find flash: MX25L25635E
*** Warning - bad CRC, using default environment
============================================
Onion Omega2 UBoot Version: 4.3.0.3
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Oct 18 2016 Time:17:29:05
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
CPU freq = 575 MHZ
Estimated memory size = 128 Mbytes
Resetting MT7628 PHY.
Initializing MT7688 GPIO system.
**************************************
* Hold Reset button for more options *
**************************************
Boot Linux from Flash NO RESET PRESSED.
##Booting image at bc050000 ...
Image Name: MIPS LEDE Linux-4.4.46
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1306785 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
##Transferring control to Linux (at address 80000000) ...
##Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 4.4.46 (root@2272a3272872) (gcc ver
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Onion Omega2+
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ff
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007f
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, line
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases,
[ 0.000000] Built 1 zonelists in Zone order, mobility groupin
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfst
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 byte
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4,
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 3
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125556K/131072K available (3013K kernel c cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1
[ 0.000000] NR_IRQS:256
[ 0.000000] intc: using register map from devicetree
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource_probe: no matching clocksources found
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, w
[ 0.007522] Calibrating delay loop... 385.84 BogoMIPS (lpj=19
[ 0.070039] pid_max: default: 32768 minimum: 301
[ 0.074637] Mount-cache hash table entries: 1024 (order: 0, 4
[ 0.080978] Mountpoint-cache hash table entries: 1024 (order:
[ 0.094317] clocksource: jiffies: mask: 0xffffffff max_cycles
[ 0.103965] pinctrl core: initialized pinctrl subsystem
[ 0.109704] NET: Registered protocol family 16
[ 0.133298] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.138834] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.144263] mt7621_gpio 10000600.gpio: registering 32 gpios
[ 0.150790] i2c-mt7621 10000900.i2c: clock 100KHz, re-start n
[ 0.158321] clocksource: Switched to clocksource MIPS
[ 0.164706] NET: Registered protocol family 2
[ 0.169804] TCP established hash table entries: 1024 (order:
[ 0.176497] TCP bind hash table entries: 1024 (order: 0, 4096
[ 0.182681] TCP: Hash tables configured (established 1024 bin
[ 0.188880] UDP hash table entries: 256 (order: 0, 4096 bytes
[ 0.194480] UDP-Lite hash table entries: 256 (order: 0, 4096
[ 0.200841] NET: Registered protocol family 1
[ 0.210542] futex hash table entries: 256 (order: -1, 3072 by
[ 0.216493] Crashlog allocated RAM at address 0x3f00000
[ 0.236685] squashfs: version 4.0 (2009/01/31) Phillip Loughe
[ 0.242338] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME
[ 0.254452] io scheduler noop registered
[ 0.258193] io scheduler deadline registered (default)
[ 0.264082] rt2880-pinmux pinctrl: pin io18 already requested
[ 0.273166] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) stat
[ 0.279177] rt2880-pinmux pinctrl: could not request pin 18 (
[ 0.288580] mtk-pwm 10005000.pwm: Error applying setting, rev
[ 0.295923] Serial: 8250/16550 driver, 4 ports, IRQ sharing d
[ 0.303489] console [ttyS0] disabled
[ 0.306924] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq
[ 0.315703] console [ttyS0] enabled
[ 0.315703] console [ttyS0] enabled
[ 0.322700] bootconsole [early0] disabled
[ 0.322700] bootconsole [early0] disabled
[ 0.331372] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 2
[ 0.340871] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 3
[ 0.351460] spi-mt7621 10000b00.spi: sys_freq: 193333333
[ 0.361496] m25p80 spi32766.0: using chunked io (size=31)
[ 0.366993] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[ 0.372562] 4 ofpart partitions found on MTD device spi32766.
[ 0.378491] Creating 4 MTD partitions on "spi32766.0":
[ 0.383709] 0x000000000000-0x000000030000 : "u-boot"
[ 0.390518] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.397716] 0x000000040000-0x000000050000 : "factory"
[ 0.404740] 0x000000050000-0x000002000000 : "firmware"
[ 0.452536] 2 uimage-fw partitions found on MTD device firmwa
[ 0.458584] 0x000000050000-0x00000018f0e1 : "kernel"
[ 0.465264] 0x00000018f0e1-0x000002000000 : "rootfs"
[ 0.472202] mtd: device 5 (rootfs) set to be root filesystem
[ 0.478020] 1 squashfs-split partitions found on MTD device r
[ 0.484358] 0x0000006f0000-0x000002000000 : "rootfs_data"
[ 0.501593] rt3050-esw 10110000.esw: link changed 0x00
[ 0.509308] mtk_soc_eth 10100000.ethernet eth0: mediatek fram
[ 0.517910] i2c /dev entries driver
[ 0.522113] mt7621_wdt 10000120.watchdog: Initialized
[ 0.528830] NET: Registered protocol family 10
[ 0.537267] NET: Registered protocol family 17
[ 0.541944] bridge: automatic filtering via arp/ip/ip6tables eed this.
[ 0.554763] 8021q: 802.1Q VLAN Support v1.8
[ 0.565991] VFS: Mounted root (squashfs filesystem) readonly
[ 0.574365] Freeing unused kernel memory: 208K (803cc000 - 80
[ 1.568540] init: Console is alive
[ 1.572220] init: - watchdog -
[ 4.000530] kmodloader: loading kernel modules from /etc/modu
[ 4.151857] usbcore: registered new interface driver usbfs
[ 4.157562] usbcore: registered new interface driver hub
[ 4.163110] usbcore: registered new device driver usb
[ 4.174558] exFAT: Version 1.2.9
[ 4.217943] SCSI subsystem initialized
[ 4.228712] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHC
[ 4.237076] ehci-platform: EHCI generic platform driver
[ 4.252764] phy phy-10120000.usbphy.0: remote usb device wake
[ 4.259582] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
[ 4.264911] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.270787] ehci-platform 101c0000.ehci: new USB bus register
[ 4.278954] ehci-platform 101c0000.ehci: irq 26, io mem 0x101
[ 4.298367] ehci-platform 101c0000.ehci: USB 2.0 started, EHC
[ 4.305819] hub 1-0:1.0: USB hub found
[ 4.310095] hub 1-0:1.0: 1 port detected
[ 4.318972] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) D
[ 4.326904] ohci-platform: OHCI generic platform driver
[ 4.332555] ohci-platform 101c1000.ohci: Generic Platform OHC
[ 4.339539] ohci-platform 101c1000.ohci: new USB bus register
[ 4.347648] ohci-platform 101c1000.ohci: irq 26, io mem 0x101
[ 4.413472] hub 2-0:1.0: USB hub found
[ 4.417710] hub 2-0:1.0: 1 port detected
[ 4.434858] MTK MSDC device init.
[ 4.478498] mtk-sd: MediaTek MT6575 MSDC Driver
[ 4.486464] sdhci: Secure Digital Host Controller Interface d
[ 4.492816] sdhci: Copyright(c) Pierre Ossman
[ 4.498714] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.509048] usbcore: registered new interface driver usb-stor
[ 4.518750] kmodloader: done loading kernel modules from /etc
[ 4.536554] init: - preinit -
[ 5.378803] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select thes read, 10 bits of entropy available)
level
[ 7.804351] mount_root: jffs2 not ready yet, using temporary
[ 7.838103] urandom-seed: Seed file not found (/etc/urandom.s
[ 8.004511] procd: - early -
[ 8.007544] procd: - watchdog -
[ 8.654352] procd: - ubus -
[ 8.858893] random: ubusd: uninitialized urandom read (4 byte
[ 8.868627] random: ubusd: uninitialized urandom read (4 byte
[ 8.877798] random: ubusd: uninitialized urandom read (4 byte
[ 8.887379] random: ubusd: uninitialized urandom read (4 byte
[ 8.896630] random: ubusd: uninitialized urandom read (4 byte
[ 8.905951] random: ubusd: uninitialized urandom read (4 byte
[ 8.915319] random: ubusd: uninitialized urandom read (4 byte
[ 8.924856] procd: - init -
Please press Enter to activate this console.
[ 9.565197] kmodloader: loading kernel modules from /etc/modu
[ 9.600719] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 9.669780] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.693881] Ralink/MTK WiFi EEPROM API Build for MT7620.
[ 9.737404] WRTnode AP Driver version: 4.1.0.0
[ 9.889466] Linux video capture interface: v2.00
[ 10.038996] hidraw: raw HID events driver (C) Jiri Kosina
[ 10.084647] Bluetooth: Core ver 2.21
[ 10.088486] NET: Registered protocol family 31
[ 10.092996] Bluetooth: HCI device and connection manager init
[ 10.099476] Bluetooth: HCI socket layer initialized
[ 10.104427] Bluetooth: L2CAP socket layer initialized
[ 10.109615] Bluetooth: SCO socket layer initialized
[ 10.117066] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 10.122535] Bluetooth: BNEP filters: protocol multicast
[ 10.127845] Bluetooth: BNEP socket layer initialized
[ 10.139759] usbcore: registered new interface driver btusb
[ 10.152744] usbcore: registered new interface driver cdc_acm
[ 10.158566] cdc_acm: USB Abstract Control Model driver for US
[ 10.183746] Bluetooth: HCI UART driver ver 2.3
[ 10.188268] Bluetooth: HCI UART protocol H4 registered
[ 10.193547] Bluetooth: HCI UART protocol BCSP registered
[ 10.203114] Bluetooth: HIDP (Human Interface Emulation) ver 1
[ 10.209214] Bluetooth: HIDP socket layer initialized
[ 10.217333] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.238730] nf_conntrack version 0.5.0 (1965 buckets, 7860 ma
[ 10.296362] Bluetooth: RFCOMM TTY layer initialized
[ 10.301418] Bluetooth: RFCOMM socket layer initialized
[ 10.306653] Bluetooth: RFCOMM ver 1.11
[ 10.318477] spidev spi32766.1: buggy DT: spidev listed direct
[ 10.325025] ------------[ cut here ]------------
[ 10.329747] WARNING: CPU: 0 PID: 472 at drivers/spi/spidev.c:
[ 10.336977] Modules linked in: spidev(+) snd_usbmidi_lib slhcrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defra ip_tables hidp hid_generic hci_uart crc_ccitt cdc_acm btusb bti960 videobuf2_vmalloc videobuf2_memops videobuf2_core hid v4l2_ceprom_api ledtrig_oneshot ledtrig_morse ledtrig_heartbeat ledtriangle ip6table_filter ip6_tables x_tables msdos snd_pcm_dmaengin snd_seq_device snd_hwdep snd input_core soundcore vfat fat ntfsed_buffer ecb cmac mmc_block usb_storage sdhci_pltfm sdhci mtk_stform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcr crc32c_generic crypto_hash
[ 10.446541] CPU: 0 PID: 472 Comm: kmodloader Not tainted 4.4.
[ 10.452816] Stack : 80368154 00000000 00000001 803b0000 87d21
80403438 0000000b 0000001a 024000c0 800661ec 8004ae0c
00000003 0000000b 8034d3a8 8751db4c 800661ec 80048d78
00000001 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
...
[ 10.488978] Call Trace:
[ 10.491519] [<800661ec>] module_sect_show+0x0/0x18
[ 10.496386] [<8004ae0c>] vprintk_default+0x24/0x30
[ 10.501276] [<800661ec>] module_sect_show+0x0/0x18
[ 10.506136] [<80048d78>] printk+0x2c/0x38
[ 10.510233] [<800253fc>] warn_slowpath_common+0xa0/0xd0
[ 10.515544] [<80149a24>] dump_stack+0x14/0x28
[ 10.519976] [<80014874>] show_stack+0x50/0x84
[ 10.524393] [<800253fc>] warn_slowpath_common+0xa0/0xd0
[ 10.529708] [<870a433c>] 0x870a433c
[ 10.533264] [<800254b4>] warn_slowpath_null+0x18/0x24
[ 10.538411] [<801f66c0>] of_match_node+0x20/0x44
[ 10.543115] [<870a433c>] 0x870a433c
[ 10.546667] [<801bbe20>] devm_kfree+0x20/0x44
[ 10.551136] [<801dd064>] spi_drv_probe+0x3c/0x84
[ 10.555831] [<801b8950>] driver_probe_device+0x120/0x288
[ 10.561251] [<8008a100>] kstrdup+0x44/0x8c
[ 10.565422] [<801dcf64>] spi_match_device+0x38/0xa8
[ 10.570405] [<801b8b34>] __driver_attach+0x7c/0xb4
[ 10.575284] [<801b6d58>] next_device+0x10/0x30
[ 10.579815] [<801b8ab8>] __driver_attach+0x0/0xb4
[ 10.584590] [<801b6e14>] bus_for_each_dev+0x9c/0xac
[ 10.589578] [<802ed674>] klist_add_tail+0x24/0x50
[ 10.594360] [<801b6be8>] bus_get+0x2c/0x50
[ 10.598557] [<801b8048>] bus_add_driver+0xec/0x20c
[ 10.603423] [<800acc7c>] exact_match+0x0/0x8
[ 10.607757] [<800ad184>] exact_lock+0x0/0x24
[ 10.612122] [<801b924c>] driver_register+0xa8/0xf8
[ 10.616987] [<870dc000>] init_module+0x0/0xdc [spidev]
[ 10.622244] [<870dc098>] init_module+0x98/0xdc [spidev]
[ 10.627551] [<801555f0>] kasprintf+0x1c/0x28
[ 10.631912] [<80045764>] __wake_up+0x24/0x48
[ 10.636247] [<870dc000>] init_module+0x0/0xdc [spidev]
[ 10.641498] [<8000d890>] do_one_initcall+0x1e8/0x214
[ 10.646550] [<80045764>] __wake_up+0x24/0x48
[ 10.650902] [<870dc000>] init_module+0x0/0xdc [spidev]
[ 10.656134] [<8003441c>] call_usermodehelper_exec+0x144/0x160
[ 10.661994] [<80033f0c>] call_usermodehelper_setup+0x38/0xa8
[ 10.667766] [<800661ec>] module_sect_show+0x0/0x18
[ 10.672664] [<8006740c>] do_init_module+0x74/0x1cc
[ 10.677536] [<8009dc30>] __vunmap+0xf0/0x114
[ 10.681917] [<80068ca0>] load_module+0x16c0/0x1b68
[ 10.686782] [<800667d8>] unknown_module_param_cb+0x0/0xac
[ 10.692278] [<8009e124>] __vmalloc_node+0x34/0x40
[ 10.697073] [<800691dc>] SyS_init_module+0x94/0x180
[ 10.702042] [<80069278>] SyS_init_module+0x130/0x180
[ 10.707107] [<8000682c>] syscall_common+0x30/0x54
[ 10.711901] [<80008c58>] __bzero+0xbc/0x164
[ 10.716143]
[ 10.717654] ---[ end trace ef0c41cacf46f24b ]---
[ 10.729744] usbcore: registered new interface driver ums-alau
[ 10.738916] usbcore: registered new interface driver ums-cypr
[ 10.748128] usbcore: registered new interface driver ums-data
[ 10.757118] usbcore: registered new interface driver ums-free
[ 10.766324] usbcore: registered new interface driver ums-isd2
[ 10.775556] usbcore: registered new interface driver ums-jump
[ 10.784676] usbcore: registered new interface driver ums-karm
[ 10.794465] usbcore: registered new interface driver ums-sddr
[ 10.803620] usbcore: registered new interface driver ums-sddr
[ 10.813101] usbcore: registered new interface driver ums-usba
[ 10.825477] usbcore: registered new interface driver usbhid
[ 10.831208] usbhid: USB HID core driver
[ 10.838966] usbcore: registered new interface driver usblp
[ 10.853137] usbcore: registered new interface driver usbseria
[ 10.859251] usbcore: registered new interface driver usbseria
[ 10.865976] usbserial: USB Serial support registered for gene
[ 10.884705] Driver for 1-wire Dallas network protocol.
[ 10.911416] xt_time: kernel timezone is -0000
[ 10.918088] usbcore: registered new interface driver ch341
[ 10.923882] usbserial: USB Serial support registered for ch34
[ 10.932667] usbcore: registered new interface driver cp210x
[ 10.938525] usbserial: USB Serial support registered for cp21
[ 10.948052] usbcore: registered new interface driver ftdi_sio
[ 10.954117] usbserial: USB Serial support registered for FTDI
[ 10.972980] usbcore: registered new interface driver pl2303
[ 10.978852] usbserial: USB Serial support registered for pl23
[ 10.990320] PPP generic driver version 2.4.2
[ 10.997883] NET: Registered protocol family 24
[ 11.016076] usbcore: registered new interface driver snd-usb-
[ 11.038113] usbcore: registered new interface driver uvcvideo
[ 11.044029] USB Video Class driver (1.1.1)
[ 11.054969] usbcore: registered new interface driver option
[ 11.060837] usbserial: USB Serial support registered for GSM
[ 11.073381] kmodloader: done loading kernel modules from /etc
[ 11.317468] random: jshn: uninitialized urandom read (4 bytes
[ 11.482165] random: jshn: uninitialized urandom read (4 bytes
[ 23.362270] EEPROM:Read from [factory] offset 0x0,length 0x40
what can i do to get wifi on and broadcast its name..?
any other options to bring up board