Hi Jose

Thanks for taking the time to reply.

I have identified that the omega2p-v0.1.10-b160.bin version of the firmware contains kernel 4.4.46
On the LEDE-Project website for supported hardware, it states that the Omega2+ is supported on LEDE 17.01 which has kernel 4.4.50.
https://lede-project.org/toh/start?dataflt[Brand*~]=onion

There were a number of issues fixed for openvpn / openssl for the 4.4.50 kernels.
https://lede-project.org/releases/17.01/notes-17.01.0

I am not sure why b160 is still using 4.4.46 while the supported version of LEDE contains 4.4.50.
The openvpn-openssl package is based on a snapshot of kernel 4.4.50.
https://lede-project.org/packages/start?dataflt[Name_pkg-page*~]=openvpn-openssl

I am going to wait in the hope that the kernel is brought up to version 4.4.50 and then the install may be successful.
As an aside, there is a SDK package available for LEDE 17.01.
https://downloads.lede-project.org/releases/17.01.0/targets/ramips/mt7688/

Cheers
Freddy

Hi Brad

I also printed the Omega case by ElmoC. It is a great case, although there doesn't seem to be consideration for the MicroSD card. A small amount of fettling was required to make it all fit. I removed the small pillar between the microUSB and fullUSB ports and all is great.

In order to hold the 2 halves together, I clamped them together and then painted the side clips with acetone. Once dried it all stays together really well, If I want to remove the Omega2 from the case then it is easy enough to break the tabs off and then reprint. I am using mine for OctoPrint, I intend adding a camera from a laptop.

I will post a picture of my case later today.
Cheers
Freddy

Hi Jose

Thanks for taking the time to reply.

I have identified that the omega2p-v0.1.10-b160.bin version of the firmware contains kernel 4.4.46
On the LEDE-Project website for supported hardware, it states that the Omega2+ is supported on LEDE 17.01 which has kernel 4.4.50.
https://lede-project.org/toh/start?dataflt[Brand*~]=onion

There were a number of issues fixed for openvpn / openssl for the 4.4.50 kernels.
https://lede-project.org/releases/17.01/notes-17.01.0

I am not sure why b160 is still using 4.4.46 while the supported version of LEDE contains 4.4.50.
The openvpn-openssl package is based on a snapshot of kernel 4.4.50.
https://lede-project.org/packages/start?dataflt[Name_pkg-page*~]=openvpn-openssl

I am going to wait in the hope that the kernel is brought up to version 4.4.50 and then the install may be successful.
As an aside, there is a SDK package available for LEDE 17.01.
https://downloads.lede-project.org/releases/17.01.0/targets/ramips/mt7688/

Cheers
Freddy

Hi Everyone

I am looking for a little assistance with my updated Omega2+.

I am able to install openvpn-openssl from http://downloads.lede-project.org/snapshots/packages/mipsel_24kc/base/ after uncommenting the distfeeds.conf file. It only allowed me to install it after using the --force-depends command as there is a kernel mismatch (clue here I think!)

It appears to install fine albeit with the kernel mismatch error, however when it connects to the VPN server I get an instant kernel panic caused by Openvpn.

The ovpn profile I am using has autologin, the profile has been tested on Android and Windows.

Has anyone managed to get Openvpn client working on the Omega2+ yet? Are there any suggestions on how I can get this working?

If there is any additional information I can provide then please let me know.
Many Thanks
Freddy

Hi
Did you manage to get OpenVPN working on the Omega2?
Thanks

This looks really good, I am going to begin the implementation tonight. Did you manage to get a webcam working with the Omega2+/OctoPrint?
I am using an Arduino + RAMPS and Marlin to run my printer. Are you aware that there is an Arduino dock for the Omega2+? I will post a picture when it has arrived.
Great work. Thanks