@Boken-Lin I am now free to roam the interwebs..
H
Posts made by Harvey Golob
-
RE: Another odd Omega not booting problemposted in Omega Talk
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin Here ya go..
********************************************* * U-Boot 1.1.4 (Sep 14 2015, 08:21:31) * ********************************************* AP121 (AR9331) U-Boot for Onion Omega DRAM: 64 MB DDR2 16-bit id read ox100000ff FLASH: 16MCLOCKS: 400/400/200/20 MHz (CPU/RAM/AHB/SPI) ## Error: MAC is invalid, using fixed! LED on during eth initialization... ## Error: MAC address in FLASH is invalid, using fixed! ## Error: MAC address in FLASH is invalid, using fixed! Hit any key to stop autobooting: 0 Booting image at: 0x9F020000 Image name: OpenWrt r47815 Image type: MIPS Linux Kernel Image (lzma compressed) Data size: 1139376 Bytes = 1.1 MB Load address: 0x80060000 Entry point: 0x80060000 Uncompressing kernel image... OK! Starting kernel... [ 0.000000] Linux version 3.18.23 (zh@ci-onion) (gcc version 4.8.3 (OpenWrt/L inaro GCC 4.8-2014.04 r47815) ) #1 Wed Dec 9 19:12:48 UTC 2015 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256 [ 0.000000] Kernel command line: board=ONION-OMEGA console=ttyATH0,115200 r ootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 60944K/65536K available (2486K kernel code, 129K rwdata, 532K rodata, 236K init, 188K bss, 4592K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.00 0MHz [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] NET: Registered protocol family 16 [ 0.100000] MIPS: machine is Onion Omega [ 0.370000] Switched to clocksource MIPS [ 0.370000] NET: Registered protocol family 2 [ 0.380000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.380000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.390000] TCP: reno registered [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.410000] NET: Registered protocol family 1 [ 0.410000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.430000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc. [ 0.440000] msgmni has been set to 119 [ 0.460000] io scheduler noop registered [ 0.460000] io scheduler deadline registered (default) [ 0.460000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 15 62500) is a AR933X UART [ 0.480000] console [ttyATH0] enabled [ 0.480000] console [ttyATH0] enabled [ 0.490000] bootconsole [early0] disabled [ 0.490000] bootconsole [early0] disabled [ 0.500000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.500000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.510000] 5 tp-link partitions found on MTD device spi0.0 [ 0.510000] Creating 5 MTD partitions on "spi0.0": [ 0.520000] 0x000000000000-0x000000020000 : "u-boot" [ 0.520000] 0x000000020000-0x0000001364b0 : "kernel" [ 0.530000] 0x0000001364b0-0x000000ff0000 : "rootfs" [ 0.530000] mtd: device 2 (rootfs) set to be root filesystem [ 0.540000] 1 squashfs-split partitions found on MTD device rootfs [ 0.540000] 0x0000007c0000-0x000000ff0000 : "rootfs_data" [ 0.550000] 0x000000ff0000-0x000001000000 : "art" [ 0.550000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.580000] libphy: ag71xx_mdio: probed [ 1.170000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd0 41, driver=Generic PHY] [ 1.180000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 1.180000] TCP: cubic registered [ 1.180000] NET: Registered protocol family 17 [ 1.190000] bridge: automatic filtering via arp/ip/ip6tables has been depreca ted. Update your scripts to load br_netfilter if you need this. [ 1.200000] 8021q: 802.1Q VLAN Support v1.8 [ 1.220000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.220000] Freeing unused kernel memory: 236K (80375000 - 803b0000) [ 2.690000] init: Console is alive [ 2.690000] init: - watchdog - [ 5.220000] usbcore: registered new interface driver usbfs [ 5.230000] usbcore: registered new interface driver hub [ 5.230000] usbcore: registered new device driver usb [ 5.290000] SCSI subsystem initialized [ 5.300000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.310000] ehci-platform: EHCI generic platform driver [ 5.310000] ehci-platform ehci-platform: EHCI Host Controller [ 5.320000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.330000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 5.350000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 5.350000] hub 1-0:1.0: USB hub found [ 5.350000] hub 1-0:1.0: 1 port detected [ 5.370000] usbcore: registered new interface driver usb-storage [ 5.720000] init: - preinit - [ 6.450000] random: procd urandom read with 10 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.630000] mount_root: loading kmods from internal overlay [ 10.010000] jffs2: notice: (337) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 10.030000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 10.040000] block: extroot: not configured [ 10.110000] jffs2: notice: (334) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 10.290000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 10.300000] block: extroot: not configured [ 10.310000] mount_root: switching to jffs2 overlay [ 10.380000] procd: - early - [ 10.380000] procd: - watchdog - [ 11.180000] procd: - ubus - [ 12.190000] procd: - init - Please press Enter to activate this console. [ 13.640000] NET: Registered protocol family 10 [ 13.660000] ntfs: driver 2.1.31 [Flags: R/O MODULE]. [ 13.680000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 13.710000] i2c /dev entries driver [ 13.720000] Custom GPIO-based I2C driver version 0.1.1 [ 13.720000] i2c-gpio i2c-gpio.0: using pins 21 (SDA) and 20 (SCL) [ 13.760000] Linux video capture interface: v2.00 [ 13.780000] hidraw: raw HID events driver (C) Jiri Kosina [ 13.820000] usbcore: registered new interface driver cdc_acm [ 13.820000] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters [ 13.830000] Loading modules backported from Linux version master-2015-03-09-0 -g141f155 [ 13.840000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 13.850000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 13.870000] nf_conntrack version 0.5.0 (955 buckets, 3820 max) [ 13.910000] usbcore: registered new interface driver ums-alauda [ 13.920000] usbcore: registered new interface driver ums-cypress [ 13.930000] usbcore: registered new interface driver ums-datafab [ 13.930000] usbcore: registered new interface driver ums-freecom [ 13.940000] usbcore: registered new interface driver ums-isd200 [ 13.950000] usbcore: registered new interface driver ums-jumpshot [ 13.960000] usbcore: registered new interface driver ums-karma [ 13.970000] usbcore: registered new interface driver ums-sddr09 [ 13.970000] usbcore: registered new interface driver ums-sddr55 [ 13.980000] usbcore: registered new interface driver ums-usbat [ 13.990000] usbcore: registered new interface driver usbhid [ 14.000000] usbhid: USB HID core driver [ 14.000000] usbcore: registered new interface driver usblp [ 14.020000] usbcore: registered new interface driver usbserial [ 14.020000] usbcore: registered new interface driver usbserial_generic [ 14.030000] usbserial: USB Serial support registered for generic [ 14.050000] usbcore: registered new interface driver uvcvideo [ 14.050000] USB Video Class driver (1.1.1) [ 14.080000] xt_time: kernel timezone is -0000 [ 14.130000] cfg80211: Calling CRDA to update world regulatory domain [ 14.130000] cfg80211: World regulatory domain updated: [ 14.140000] cfg80211: DFS Master region: unset [ 14.140000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time) [ 14.150000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 m Bm), (N/A) [ 14.160000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 m Bm), (N/A) [ 14.170000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 m Bm), (N/A) [ 14.170000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 m Bm), (N/A) [ 14.180000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 2000 mBm), (0 s) [ 14.190000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 14.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 m Bm), (N/A) [ 14.210000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 14.230000] usbcore: registered new interface driver ch341 [ 14.230000] usbserial: USB Serial support registered for ch341-uart [ 14.240000] usbcore: registered new interface driver cp210x [ 14.240000] usbserial: USB Serial support registered for cp210x [ 14.250000] usbcore: registered new interface driver ftdi_sio [ 14.260000] usbserial: USB Serial support registered for FTDI USB Serial Devi ce [ 14.370000] usbcore: registered new interface driver pl2303 [ 14.370000] usbserial: USB Serial support registered for pl2303 [ 14.380000] PPP generic driver version 2.4.2 [ 14.390000] NET: Registered protocol family 24 [ 14.480000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 14.490000] cfg80211: Calling CRDA for country: US [ 14.500000] cfg80211: Regulatory domain changed to country: US [ 14.500000] cfg80211: DFS Master region: FCC [ 14.510000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time) [ 14.520000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 m Bm), (N/A) [ 14.520000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 1700 mBm), (N/A) [ 14.530000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 2300 mBm), (0 s) [ 14.540000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 m Bm), (N/A) [ 14.550000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 40 00 mBm), (N/A) [ 81.290000] random: nonblocking pool is initialized -
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin Reflashed firmware (omega-v0.0.5-b238) and let boot, then restarted and reflashed ART, let it boot and then factory reset, still no change. Missing something?
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin Finally got back to this, started Omega, did factory reset and still no wifi. Just to be sure dropped to Uboot and started httpd and tried to reflash ART. Then did factory reset and no change.
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin Flashed ART just now, no change. Also tried hotspot suggestion, scan from Omega still fails. ifconfig only shows lo and eth0. Headed to work now, will check back end of day.
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin Omega seems to run as expected except no wifi, have gone over another post related to no wifi and can't get any response from Omega as far as wifi set up. The following is what I get.
BusyBox v1.23.2 (2015-12-09 19:09:31 UTC) built-in shell (ash) ____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/ ----------------------------------------------------- Ī©-ware: 0.0.5 b238 -------------------------------------------------- root@Omega-6CF0:/# wifi root@Omega-6CF0:/# ifconfig -a eth0 Link encap:Ethernet HWaddr B6:F4:3C:BE:6C:F0 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:240 errors:0 dropped:0 overruns:0 frame:0 TX packets:240 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16992 (16.5 KiB) TX bytes:16992 (16.5 KiB) root@Omega-6CF0:/# wifisetup -ssid linksys -auth none -password "" > Connecting to linksys network using intf 1... > Checking wwan device status... > wwan is not up!! > Disabling network on iface 1 ... > Done!The last post to https://community.onion.io/topic/135/omega-can-t-connect-to-wifi didn't seem to have resolved similar issues. Any other suggestions?
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin It's ALIVE....., thanks for the help, I had moved the connection to the laptop yesterday but didn't try tftp on the laptop.
Reflashed Uboot and httpd to load the latest Omega firmware an its up and running. Now to tackle wifisetup
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin I was wondering if something like that might be the case. Will setup a laptop with the Tftp server and try...
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin I'm doing this over my LAN so tftp server is at 192.168.0.102. When running tftp get this:
ar7240> setenv ipaddr 192.168.0.200 ar7240> setenv serverip 192.168.0.102 ar7240> tftp 0x800000000 uboot.bin dup 1 speed 10 Using eth0 device TFTP from server 192.168.0.102; our IP address is 192.168.0.200 Filename 'uboot.bin'. Load address: 0x0 Loading: * TFTP error: 'Cannot open file '.\tftp_root\uboot.bin'. (The system cannot find the file specified.)' (1) Starting again eth1 link down FAILWhen setting IP on the Omega in Uboot have not been able to ping from either end, yet when Omega boots to Linux can ping from both sides of the connection...
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin help listing:
ar7240> help reset - Perform RESET of the CPU ? - alias for 'help' boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootm - boot application image from memory cp - memory copy erase - erase FLASH memory help - print online help md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables progmac - Set ethernet MAC addresses run - run commands in an environment variable setenv - set environment variables tftpboot- boot image via network using TFTP protocol version - print monitor version ar7240>Running Win 7. Have setup TFTP Turbo4 and was going to attempt tftpboot of the latest firmware but can't seem to get the ethernet link working in uboot. Maybe I'm missing something?
-
RE: Another odd Omega not booting problemposted in Omega Talk
@Boken-Lin Output of httpd in uboot:
U-Boot 1.1.4 (Aug 28 2015 - 16:51:26) AP121 (ar9331) U-boot DRAM: 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 140k for U-Boot at: 83fdc000 Reserving 192k for malloc() at: 83fac000 Reserving 44 Bytes for Board Info at: 83fabfd4 Reserving 36 Bytes for Global Data at: 83fabfb0 Reserving 128k for boot params() at: 83f8bfb0 Stack Pointer at: 83f8bf98 Now running in RAM - U-Boot at: 83fdc000 Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18 flash size 16777216, sector count = 256 Flash: 16 MB Using default environment In: serial Out: serial Err: serial Net: ag7240_enet_initialize... No valid address in Flash. Using fixed address No valid address in Flash. Using fixed address : cfg1 0x5 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad eth0 up : cfg1 0xf cfg2 0x7214 eth1: 00:03:7f:09:0b:ad athrs26_reg_init_lan ATHRS26: resetting s26 ATHRS26: s26 reset done eth1 up eth0, eth1 Hit any key to stop autoboot: 0 ar7240> httpd Unknown command 'httpd' - try 'help' ar7240> -
Another odd Omega not booting problemposted in Omega Talk
Received my Omega package about 2 weeks ago. On powering up (following the Getting started Tut) got no LED on the Omega. Thinking some one else had been there and done that came to the forum and found several similar posts. Seems my Omega has a pre-production image. That said, not having the Ethernet board, built my own following posts elsewhere on the forum and then things get weird. On booting (not to Uboot) am able to configure eth0 and can ping from my network to and from the Omega. If I drop to Uboot am unable to get networking to work at all, have tried over LAN and direct to PC. I know my wiring is OK as I can establish a connection if I don't drop to Uboot. Also, have seen several posts by others describing using httpd in Uboot, if I try I get "Unknown command", but httpd seems to function on allowing a full boot...
Any suggestions/help would be greatly appreciated.