When I turn it on normally the LED is solid all the time

@crispyoz I press the reset key and turn it on, it starts flashing for 30 seconds (after 11 seconds I release the reset), it turns off and turns on remaining solid, I check the wifi connection and I can't find it.

ls -la /dev/ttyUSB0* -> crw-rw---- 1 root dialout 188, 0 mar 13 02:33 /dev/ttyUSB0
sudo screen /dev/ttyUSB0 115200 -> same result
sudo minicom -D /dev/ttyUSB0 -> same result

I have already tried another cable and on a macbook (I installed the drive but the USB was not displayed)

with this command sudo dmesg?

[32670.851688] usb 1-10: new full-speed USB device number 27 using xhci_hcd
[32671.126168] usb 1-10: New USB device found, idVendor=10c4, idProduct=ea60, bcdDevice= 1.00
[32671.126172] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[32671.126174] usb 1-10: Product: CP2102 USB to UART Bridge Controller
[32671.126176] usb 1-10: Manufacturer: Silicon Labs
[32671.126178] usb 1-10: SerialNumber: 0001
[32671.143174] cp210x 1-10:1.0: cp210x converter detected
[32671.159190] usb 1-10: cp210x converter now attached to ttyUSB0
[32748.025003] usb 1-10: USB disconnect, device number 27
[32748.025209] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0
[32748.025231] cp210x 1-10:1.0: device disconnected
[32759.872249] usb 1-10: new full-speed USB device number 28 using xhci_hcd
[32760.146626] usb 1-10: New USB device found, idVendor=10c4, idProduct=ea60, bcdDevice= 1.00
[32760.146630] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[32760.146633] usb 1-10: Product: CP2102 USB to UART Bridge Controller
[32760.146634] usb 1-10: Manufacturer: Silicon Labs
[32760.146636] usb 1-10: SerialNumber: 0001
[32760.163648] cp210x 1-10:1.0: cp210x converter detected
[32760.179611] usb 1-10: cp210x converter now attached to ttyUSB0

I've tried, it blinks for about 30 seconds but nothing happens

My Omega2 + mini Dock does not start the wifi network (it was a long time ago, I don't remember what I did to make this happen), so I'm trying to update the firmware via USB, I'm following the documentation but I can't connect to the serial port, when I run the command screen /dev/ttyUSB0 115200 the terminal has no response (yes, I pressed enter several times), after closing the terminal and running the command sudo dmesg I have the error: cp210x ttyUSB0: failed set request 0x12 status: -110

is he dead?

I did reset and I can not connect any more without wifi, and the console no longer works.

accessing http://192.168.3.1/:

Index of /console/

../
modified: Thu, 01 Jan 1970 00:00:08 GMT
directory - 0.00 kbyte

lib/
modified: Thu, 01 Jan 1970 00:00:11 GMT
directory - 0.00 kbyte

in ssh:

wifisetup

1, selection, password...

oupgrade -check

Device Firmware Version: 0.1.10 b160
Checking latest version online...
ERROR: Could not connect to Onion Firmware Server! Check your internet connection and try again!

very frustrated

I want to install a package that has in openwrt