Posts made by marc rozender

Yes, the terminal screen just goes blank. I tried PuTTY SSH but no luck.
I finally found the access point by setting up a hidden network. Its Omega-132D.
I can then go to the setup wizard page on the browser but then everything is greyed out and i can't do anything. The "login to Omega" doesnt go green either by itself or by clicking on it.

Hi Lazar looks like its being mapped....

Here is the output unplugged:

[bunchy@Lapbunchy ~]$ sudo ls /dev/tty*
[sudo] password for bunchy:
/dev/tty /dev/tty20 /dev/tty33 /dev/tty46 /dev/tty59 /dev/ttyS12 /dev/ttyS25
/dev/tty0 /dev/tty21 /dev/tty34 /dev/tty47 /dev/tty6 /dev/ttyS13 /dev/ttyS26
/dev/tty1 /dev/tty22 /dev/tty35 /dev/tty48 /dev/tty60 /dev/ttyS14 /dev/ttyS27
/dev/tty10 /dev/tty23 /dev/tty36 /dev/tty49 /dev/tty61 /dev/ttyS15 /dev/ttyS28
/dev/tty11 /dev/tty24 /dev/tty37 /dev/tty5 /dev/tty62 /dev/ttyS16 /dev/ttyS29
/dev/tty12 /dev/tty25 /dev/tty38 /dev/tty50 /dev/tty63 /dev/ttyS17 /dev/ttyS3
/dev/tty13 /dev/tty26 /dev/tty39 /dev/tty51 /dev/tty7 /dev/ttyS18 /dev/ttyS30
/dev/tty14 /dev/tty27 /dev/tty4 /dev/tty52 /dev/tty8 /dev/ttyS19 /dev/ttyS31
/dev/tty15 /dev/tty28 /dev/tty40 /dev/tty53 /dev/tty9 /dev/ttyS2 /dev/ttyS4
/dev/tty16 /dev/tty29 /dev/tty41 /dev/tty54 /dev/ttyprintk /dev/ttyS20 /dev/ttyS5
/dev/tty17 /dev/tty3 /dev/tty42 /dev/tty55 /dev/ttyS0 /dev/ttyS21 /dev/ttyS6
/dev/tty18 /dev/tty30 /dev/tty43 /dev/tty56 /dev/ttyS1 /dev/ttyS22 /dev/ttyS7
/dev/tty19 /dev/tty31 /dev/tty44 /dev/tty57 /dev/ttyS10 /dev/ttyS23 /dev/ttyS8
/dev/tty2 /dev/tty32 /dev/tty45 /dev/tty58 /dev/ttyS11 /dev/ttyS24 /dev/ttyS9

and plugged:

[bunchy@Lapbunchy ~]$ sudo ls /dev/tty*
/dev/tty /dev/tty21 /dev/tty35 /dev/tty49 /dev/tty62 /dev/ttyS17 /dev/ttyS30
/dev/tty0 /dev/tty22 /dev/tty36 /dev/tty5 /dev/tty63 /dev/ttyS18 /dev/ttyS31
/dev/tty1 /dev/tty23 /dev/tty37 /dev/tty50 /dev/tty7 /dev/ttyS19 /dev/ttyS4
/dev/tty10 /dev/tty24 /dev/tty38 /dev/tty51 /dev/tty8 /dev/ttyS2 /dev/ttyS5
/dev/tty11 /dev/tty25 /dev/tty39 /dev/tty52 /dev/tty9 /dev/ttyS20 /dev/ttyS6
/dev/tty12 /dev/tty26 /dev/tty4 /dev/tty53 /dev/ttyprintk /dev/ttyS21 /dev/ttyS7
/dev/tty13 /dev/tty27 /dev/tty40 /dev/tty54 /dev/ttyS0 /dev/ttyS22 /dev/ttyS8
/dev/tty14 /dev/tty28 /dev/tty41 /dev/tty55 /dev/ttyS1 /dev/ttyS23 /dev/ttyS9
/dev/tty15 /dev/tty29 /dev/tty42 /dev/tty56 /dev/ttyS10 /dev/ttyS24 /dev/ttyUSB0
/dev/tty16 /dev/tty3 /dev/tty43 /dev/tty57 /dev/ttyS11 /dev/ttyS25
/dev/tty17 /dev/tty30 /dev/tty44 /dev/tty58 /dev/ttyS12 /dev/ttyS26
/dev/tty18 /dev/tty31 /dev/tty45 /dev/tty59 /dev/ttyS13 /dev/ttyS27
/dev/tty19 /dev/tty32 /dev/tty46 /dev/tty6 /dev/ttyS14 /dev/ttyS28
/dev/tty2 /dev/tty33 /dev/tty47 /dev/tty60 /dev/ttyS15 /dev/ttyS29
/dev/tty20 /dev/tty34 /dev/tty48 /dev/tty61 /dev/ttyS16 /dev/ttyS3

Hi Boken
I tried that and all i get is a fully blank terminal.

Hi Boken
I used just like it says in the setup page :
screen /dev/tty.SLAB_USBtoUART 115200

Hi

I can't seem to setup my Onion.
Im using linux ubuntu and when im plugged in with a good cable (led stops blinking) there is no access point showing up.
I would like to use the gui but i tried the Terminal too. I read on some other thread that there may be a mixup with OSX setup commands and Linux. Is this possible?
I installed "Screen" and when i run Step 5, i get [Screen is terminating].

Could somebody help? Thank you!