Can I recover the Omega Arduino-Dock bad bootloader?

JESUS MARTINEZ

I need your help.
Apparently I loaded a sketch and I lost the bootloader of the atmega 328p AU of the dock.
I tried to recover it using ICSP and an Arduino UNO card following the tutorial:
https://www.arduino.cc/en/Tutorial/ArduinoISP
I have connected pins 13-12-11-10 from the Arduino Uno board to the Omega dock ISCP 13 with SCK, 12 with MISO, 11 with MOSI, 10 with RST, Vcc to 5v and GND
I charge the sketch in the arduino but when I burn the booloader:
I always get an error:
Should we put some capacitor? It has a solution ? Can not the ATMEL 328pAU be programmed?
Puff.... Thanks
Best Regards

     System wide configuration file is "C:\Program Files (x86)\ArduinoBIS\hardware\tools\avr/etc/avrdude.conf"

     Using Port                    : COM8
     Using Programmer              : arduino
     Overriding Baud Rate          : 19200

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x15
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

                              Block Poll               Page                       Polled
       Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
       ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
       eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
       flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
       lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
       calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
       signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

     Programmer Type : Arduino
     Description     : Arduino

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x14

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x02

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x10
Hardware Version: 4744608
Firmware Version: 0.4611299
Topcard : STK502
Error quemando bootloader
Vtarget : 1.8 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us

avrdude: stk500_initialize(): (b) protocol error, expect=0x10, resp=0x01
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.

avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x10

avrdude done. Thank you.

JESUS MARTINEZ

Has this problem happened to anyone?
I'm desperate. It's happened to me on 2 boards

György Farkas

@JESUS-MARTINEZ Are you really talking about the first version of Arduino Dock please?

JESUS MARTINEZ

@György-Farkas said in Can I recover the Omega Arduino-Dock bad bootloader?:

Are you really talking about the first version of Arduino Dock please?

No .The Board is Arduino-Dock R2. Thanks

György Farkas

@JESUS-MARTINEZ Were you able to recover that Arduino bootloader? Please let me know if you still need help.

Ary Vinicius Nervis Frigeri

I have the same problem, hope that someone find hot to solve this...

György Farkas

@Ary-Vinicius--Nervis-Frigeri Please. Some detail would be very-very nice.
You have an Omega2(?) FW v0.?.? ???, an Arduino Dock 2, a host PC with some OS ??? and with Arduino IDE v1.?.?, ...
You want to flash some bootloader into the on board ATmega chip. Which one?
BTW what does "recover" exactly mean for you in this context?
Thank you.