Omega mini dock
-
I read on here a couple of weeks ago that apparently the original mini dock doesn't work fully with
the Omega 2+ (reset button). When will a newer mini dock be available on the Onion store?
-
@Anders-Öster
It is / was not a hardware problem.@Lazar-Demin said in Omega2+: reboot and sd card fixed!:
As of firmware b143, reboot and mounting/reading/writing SD cards has been fixed!
So theoretically
the BUTTON (called RESET BUTTON) should work with all firmwares since omega2-v0.1.7-b143.bin 12-Jan-2017 22:45.
-
Hmm maybe so. But I need to do factory reset by holding the reset button on booting, and doesn't seem to work.
I saw in som ethread here someone mentioned that the reset button of the original mini dock doesn't work when trying to do that.
-
@Anders-Öster That is my experience - the reset button on the original Mini Docks doesn't work with the Omega 2s. You can do the resets on Omega2 by connecting a wire from the 3V3 pin to the FW RST pin for the appropriate time. This topic has more detail about wiring a reset.
-
@Anders-Öster said in Omega mini dock:
But I need to do factory reset by holding the reset button on booting, and doesn't seem to work.
Simply connect the (FW RST --- 38) labeled pin to HIGH level (+3.3V is a good choice) more than 10 seconds - with or without a dock.
I am afraid a factory restore can be triggered on a working (ie not bricked) Omega2+ only.
-
Thanks to both, I wil try with a wire.
@György-Farkas - by pressing the reset button duriing boot you can access a menu and choose to flash the Omega 2+ from USB even when it is bricked as I understand it.
-
@Anders-Öster said in Omega mini dock:
Thanks to both, I wil try with a wire.
@György-Farkas - by pressing the reset button duriing boot you can access a menu and choose to flash the Omega 2+ from USB even when it is bricked as I understand it.
Different actions with different results.
- FACTORY RESET (performed by Kernel)
Turn Omega's power ON and on the running system
Press and hold down the RESET BUTTON about 10 seconds
BusyBox v1.26.2 () built-in shell (ash) ____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/ ----------------------------------------------------- Ω-ware: 0.1.10 b160 ----------------------------------------------------- root@Omega-5BE1:/# FACTORY RESET [ 90.703771] br-wlan: port 2(ra0) entered disabled state [ 90.709234] br-wlan: port 1(eth0.1) entered disabled state [ 90.759208] device eth0.1 left promiscuous mode [ 90.763821] device eth0 left promiscuous mode [ 90.768346] br-wlan: port 1(eth0.1) entered disabled state [ 90.787550] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 90.803290] device ra0 left promiscuous mode [ 90.807819] br-wlan: port 2(ra0) entered disabled state [ 91.015109] !!! APCLI LINK DOWN - IF(apcli0)!!! [ 95.088252] Removing MTD device #6 (rootfs_data) with use count 1 [ 95.121843] reboot: Restarting system ____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/" Board: Onion Omega2 APSoC DRAM: 128 MB relocate_code Pointer at: 87f60000 ****************************** Software System Reset Occurred ****************************** flash manufacture id: c2, device id 20 19 find flash: MX25L25635E *** Warning - bad CRC, using default environment ============================================ Onion Omega2 UBoot Version: 4.3.0.3 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 1024 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 128 MBytes Flash component: SPI Flash Date:Oct 18 2016 Time:17:29:05 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 CPU freq = 575 MHZ Estimated memory size = 128 Mbytes Resetting MT7628 PHY. Initializing MT7688 GPIO system. ************************************** * Hold Reset button for more options * ************************************** Boot Linux from Flash NO RESET PRESSED.and so on...
- Flash firmware from USB storage (performed by UBoot)
Press and hold down the RESET BUTTON
Turn Omega's power ON
____ _ ____ / __ \___ (_)__ ___ / __ \__ _ ___ ___ ____ _ / /_/ / _ \/ / _ \/ _ \ / /_/ / ' \/ -_) _ `/ _ `/ \____/_//_/_/\___/_//_/ \____/_/_/_/\__/\_, /\_,_/ W H A T W I L L Y O U I N V E N T ? /___/" Board: Onion Omega2 APSoC DRAM: 128 MB relocate_code Pointer at: 87f60000 flash manufacture id: c2, device id 20 19 find flash: MX25L25635E *** Warning - bad CRC, using default environment ============================================ Onion Omega2 UBoot Version: 4.3.0.3 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 1024 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 128 MBytes Flash component: SPI Flash Date:Oct 18 2016 Time:17:29:05 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 CPU freq = 575 MHZ Estimated memory size = 128 Mbytes Resetting MT7628 PHY. Initializing MT7688 GPIO system. ************************************** * Hold Reset button for more options * ************************************** You have 40 seconds left to select a menu option... Please select option: [ Enter ]: Boot Omega2. [ 0 ]: Start Web recovery mode. [ 1 ]: Start command line mode. [ 2 ]: Flash firmware from USB storage. Option [2] selected.and so on...
- FACTORY RESET (performed by Kernel)
