Hi,
Ive finally received my new OMEGA 2+ board plus everything else. I was able to go through the initial setup using the power dock, all seem to have worked fine, setup the wifi, did the firmware update, and did the reboot. The next day, nothing seems to work, the light on the OMEGA 2+ doesn’t come on; it’s making a high pitch noise. Im still using the power dock. I tried to power it with the MINI dock, it still doesn’t power up, no light comes on, on the OMEGA 2+, and the MINI dock gets extremely hot. I tried the same with the breadboard dock and get the same result, no lights on the OMEGA 2+ and the breadboard dock get extremely hot. Tried De-Brick the Omega with Ethernet Expansion procedure, with no success.
If I purchase a new OMEGA 2+ with INDIEGOGO, do you know how long it would take before I would get a new one.
Thanks
Claude
Posts made by claude hurtubise
-
OMEGA 2+ not working after initial setupposted in Omega Talk
-
RE: Relayposted in Omega Talk
Jeff, thank you for the information, its greatly appropriated
Claude.
-
RE: Relayposted in Omega Talk
another question, I would like to use a 5 volt power supply as a source for a light this time and not use 5 volt from the Omega. Would I need to ground my power supply with the omega extension board, the ground on the power supply connected to the ground on the Omega?
Thanks
-
RE: Relayposted in Omega Talk
Thank you Jeff, The confusion part for me was the IN and OUT written on the board. To test the relay I got myself a cheap USB light thing, took it apart and re-wired it and was able to control with the relay, turning it on and off, This was need
-
Relayposted in Omega Talk
I recently received got my relay expansion board. I
d like to try it out, but Im not sure where to start. Ive looked online for example, but haven’t found anything that would explain clearly how to do the electrical connection to the relay. Im seeing 2 IN and 2 OUT on this relay board, I`m not sure were to get the ground. If someone could suggest a tutorial or a webpage with clear instaruction.
Thanks -
Tor on Onionposted in Omega Talk
Hi,
Would running Tor be possible?http://hackriculture.fr/routeur-wifi-anonymisant-avec-tor-et-openwrt.html
unfortunately this link is in french
Thanks
-
RE: help with arduino dockposted in Omega Talk
Thanks for your reply
this is what I get after executing the follwoing, i2cdetect -y 0
root@Omega-0B03:~# i2cdetect -y 0
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f
10: 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
20: 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
30: 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f
40: 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f
70: 70 71 72 73 74 75 76 77
root@Omega-0B03:~# -
help with arduino dockposted in Omega Talk
Hi,
would someone be able to help out with the arduino dock. I was able to do the initial setup, and it looks like it worked..- the result ----
root@Omega-0B03:~# sh /usr/bin/arduino-dock flash bootloader > Flashing bootloader... avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e950f avrdude: erasing chip avrdude: reading input file "0x3f" avrdude: writing lock (1 bytes): Writing | ################################################## | 100% 0.00s avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0x3f: avrdude: load data lock data from input file 0x3f: avrdude: input file 0x3f contains 1 bytes avrdude: reading on-chip lock data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of lock verified avrdude: reading input file "0x05" avrdude: writing efuse (1 bytes): Writing | ################################################## | 100% 0.00s avrdude: 1 bytes of efuse written avrdude: verifying efuse memory against 0x05: avrdude: load data efuse data from input file 0x05: avrdude: input file 0x05 contains 1 bytes avrdude: reading on-chip efuse data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of efuse verified avrdude: reading input file "0xDA" avrdude: writing hfuse (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of hfuse written avrdude: verifying hfuse memory against 0xDA: avrdude: load data hfuse data from input file 0xDA: avrdude: input file 0xDA contains 1 bytes avrdude: reading on-chip hfuse data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of hfuse verified avrdude: reading input file "0xFF" avrdude: writing lfuse (1 bytes): Writing | ################################################## | 100% 0.00s avrdude: 1 bytes of lfuse written avrdude: verifying lfuse memory against 0xFF: avrdude: load data lfuse data from input file 0xFF: avrdude: input file 0xFF contains 1 bytes avrdude: reading on-chip lfuse data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of lfuse verified avrdude done. Thank you. avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e950f avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "/usr/share/arduino-dock/twibootloader.hex" avrdude: input file /usr/share/arduino-dock/twibootloader.hex auto detected as Intel Hex avrdude: writing flash (31808 bytes): Writing | ################################################## | 100% 1.19s avrdude: 31808 bytes of flash written avrdude: verifying flash memory against /usr/share/arduino-dock/twibootloader.hex: avrdude: load data flash data from input file /usr/share/arduino-dock/twibootloader.hex: avrdude: input file /usr/share/arduino-dock/twibootloader.hex auto detected as Intel Hex avrdude: input file /usr/share/arduino-dock/twibootloader.hex contains 31808 bytes avrdude: reading on-chip flash data: Reading | ################################################## | 100% 1.14s avrdude: verifying ... avrdude: 31808 bytes of flash verified avrdude: reading input file "0x0f" avrdude: writing lock (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0x0f: avrdude: load data lock data from input file 0x0f: avrdude: input file 0x0f contains 1 bytes avrdude: reading on-chip lock data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of lock verified avrdude: safemode: Fuses OK (E:05, H:DA, L:FF) avrdude done. Thank you. > Done root@Omega-0B03:~# I get an error once trying to run the pgm blink2, because I'm not seeing the Omega in the port menu in the Arduino IDE, I'm using the second method, > Flashing application 'blink2.hex' ... device : /dev/i2c-0 (address: 0x29) version : (sig: 0x00 0x00 0x00 => unknown) flash size : 0x0000 / 0 (0x00 bytes/page) eeprom size : 0x0000 / 0 invalid memsize: 0x0c8a > 0x0000 > Doneany help would be great
Thanks
Claude -
RE: need help using Arduino Dockposted in Omega Talk
I tried re flashing the arduino dock again, that seem to have work, I get in trouble once I try flashing the blink2 sketch, using the second method, because I'm not seeing the Omega in the port menu in the Arduino IDE
Flashing application 'blink2.hex' ...
device : /dev/i2c-0 (address: 0x29)
version : (sig: 0x00 0x00 0x00 => unknown)
flash size : 0x0000 / 0 (0x00 bytes/page)
eeprom size : 0x0000 / 0
invalid memsize: 0x0c8a > 0x0000
Done -
RE: need help using Arduino Dockposted in Omega Talk
I used the second method "using the Omega" because I was not seeing the Omega in the port menu in the Arduino IDE.
The yellow led on the Arduino board is flashing very slowly all the time.Thanks
Claude -
need help using Arduino Dockposted in Omega Talk
Hi,
I'm really enjoying your product.
I was able to do the initial setup for the arduino dockthe following was the result
root@Omega-0B03:~# sh /usr/bin/arduino-dock flash bootloader > Flashing bootloader... avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e950f avrdude: erasing chip avrdude: reading input file "0x3f" avrdude: writing lock (1 bytes): Writing | ################################################## | 100% 0.00s avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0x3f: avrdude: load data lock data from input file 0x3f: avrdude: input file 0x3f contains 1 bytes avrdude: reading on-chip lock data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of lock verified avrdude: reading input file "0x05" avrdude: writing efuse (1 bytes): Writing | ################################################## | 100% 0.00s avrdude: 1 bytes of efuse written avrdude: verifying efuse memory against 0x05: avrdude: load data efuse data from input file 0x05: avrdude: input file 0x05 contains 1 bytes avrdude: reading on-chip efuse data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of efuse verified avrdude: reading input file "0xDA" avrdude: writing hfuse (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of hfuse written avrdude: verifying hfuse memory against 0xDA: avrdude: load data hfuse data from input file 0xDA: avrdude: input file 0xDA contains 1 bytes avrdude: reading on-chip hfuse data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of hfuse verified avrdude: reading input file "0xFF" avrdude: writing lfuse (1 bytes): Writing | ################################################## | 100% 0.00s avrdude: 1 bytes of lfuse written avrdude: verifying lfuse memory against 0xFF: avrdude: load data lfuse data from input file 0xFF: avrdude: input file 0xFF contains 1 bytes avrdude: reading on-chip lfuse data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of lfuse verified avrdude done. Thank you. avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e950f avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "/usr/share/arduino-dock/twibootloader.hex" avrdude: input file /usr/share/arduino-dock/twibootloader.hex auto detected as Intel Hex avrdude: writing flash (31808 bytes): Writing | ################################################## | 100% 1.19s avrdude: 31808 bytes of flash written avrdude: verifying flash memory against /usr/share/arduino-dock/twibootloader.hex: avrdude: load data flash data from input file /usr/share/arduino-dock/twibootloader.hex: avrdude: input file /usr/share/arduino-dock/twibootloader.hex auto detected as Intel Hex avrdude: input file /usr/share/arduino-dock/twibootloader.hex contains 31808 bytes avrdude: reading on-chip flash data: Reading | ################################################## | 100% 1.14s avrdude: verifying ... avrdude: 31808 bytes of flash verified avrdude: reading input file "0x0f" avrdude: writing lock (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0x0f: avrdude: load data lock data from input file 0x0f: avrdude: input file 0x0f contains 1 bytes avrdude: reading on-chip lock data: Reading | ################################################## | 100% 0.00s avrdude: verifying ... avrdude: 1 bytes of lock verified avrdude: safemode: Fuses OK (E:05, H:DA, L:FF) avrdude done. Thank you. > Done root@Omega-0B03:~# ------------------------------------------------now trying to to flash the blink2 example I get an memsize error, not sure how to proceed, any suggestion
would be appropriated, Thanks> Flashing application 'blink2.hex' ... device : /dev/i2c-0 (address: 0x29) version : (sig: 0x00 0x00 0x00 => unknown) flash size : 0x0000 / 0 (0x00 bytes/page) eeprom size : 0x0000 / 0 invalid memsize: 0x0c8a > 0x0000 > Done