1. Home
  2. Omega Talk
  3. Omega2+ fails to connect to wifi

Omega2+ fails to connect to wifi

  • Gabriel Ongpauco

    @Kostas-David , @Marcin-Nosek , @zc-Zhang

    If you are using a non-US router that uses channels 12-14, please follow the instructions by Rick Hogervorst and Larry Pinney here: http://community.onion.io/topic/1138/connecting-the-omega2-to-wifi-channels-12-to-14-for-non-us-users/4

    If this does not work, please post screen captures or terminal output when running wifisetup and scanning for available networks. If pasting terminal output, enclose it in a Code Block as shown in this guide: https://confluence.atlassian.com/bitbucketserver/markdown-syntax-guide-776639995.html#Markdownsyntaxguide-Codeblocks

    Please also post the output of running uci show wireless (remove your network SSIDs and passwords first!) and uci show network. Enclose these outputs in Code Blocks as shown earlier.

    Thanks,
    Gabe

    0
  • Y

    My Omega2+ still cannot connect my to Mikrotik Router
    firmware version: 0.1.7 b140

    wifisetup scan

    root@Omega-4877:~# wifisetup
Onion Omega Wifi Setup

Select from the following:
1) Scan for Wifi networks
2) Type network info
q) Exit

Selection: 1
Scanning for wifi networks...

Select Wifi network:
1) Guest_1195
2) YEWEIAP2
3) YWSMART
4) YWGUEST

    wifisetup list

    root@Omega-4877:~# wifisetup list
{

        "results": [
 {

        "ssid": "YEWEIAP2",
        "encryption": "WPA2PSK",
        "password": "PASSWORD"
}
]
}

    uci show wireless

    root@Omega-4877:~# uci show wireless
wireless.ra0=wifi-device
wireless.ra0.type='ralink'
wireless.ra0.mode='9'
wireless.ra0.channel='auto'
wireless.ra0.txpower='100'
wireless.ra0.ht='20'
wireless.ra0.country='CN'
wireless.ra0.countryregion='1'
wireless.ra0.disabled='0'
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='ra0'
wireless.@wifi-iface[0].network='wlan'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].key='12345678'
wireless.@wifi-iface[0].ApCliEncrypType='AES'
wireless.@wifi-iface[0].ApCliSsid='YEWEIAP2'
wireless.@wifi-iface[0].ApCliPassWord='PASSWORD'
wireless.@wifi-iface[0].ApCliAuthMode='WPA2PSK'
wireless.@wifi-iface[0].ApCliEnable='0'
wireless.@wifi-iface[0].ssid='Omega-4877'
wireless.@wifi-config[0]=wifi-config
wireless.@wifi-config[0].ssid='YEWEIAP2'
wireless.@wifi-config[0].encryption='WPA2PSK'
wireless.@wifi-config[0].key='PASSWORD''
root@Omega-4877:~#

    uci show network

    root@Omega-4877:~# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd1d:48c4:7633::/48'
network.wlan=interface
network.wlan.type='bridge'
network.wlan.ifname='eth0.1'
network.wlan.proto='static'
network.wlan.ipaddr='192.168.3.1'
network.wlan.netmask='255.255.255.0'
network.wlan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'
root@Omega-4877:~#

    /etc/config/wireless

    root@Omega-4877:~# cat /etc/config/wireless

config wifi-device 'ra0'
        option type 'ralink'
        option mode '9'
        option channel 'auto'
        option txpower '100'
        option ht '20'
        option country 'CN'
        option countryregion '1'
        option disabled '0'

config wifi-iface
        option device 'ra0'
        option network 'wlan'
        option mode 'ap'
        option encryption 'psk2'
        option key '12345678'
        option ApCliEncrypType 'AES'
        option ApCliSsid 'YEWEIAP2'
        option ApCliPassWord 'PASSWORD'
        option ApCliAuthMode 'WPA2PSK'
        option ApCliEnable '0'
        option ssid 'Omega-4877'

config wifi-config
        option ssid 'YEWEIAP2'
        option encryption 'WPA2PSK'
        option key 'PASSWORD'

root@Omega-4877:~#
    0
  • D

    Hello!
    I have same issue with connecting Omega2+ to my Mikrotik router. I'm from Russia, so I'm not using channels 12, 13 and so on.
    FW Version 0.1.7 b140
    Here is the output from Omega2:

    wifisetup scan

    root@Omega-B8B3:/# wifisetup
Onion Omega Wifi Setup

Select from the following:
1) Scan for Wifi networks
2) Type network info
q) Exit

Selection: 1
Scanning for wifi networks...

Select Wifi network:
1) Home
2) Why-Fi
3) TP_New
4) MGTS_GPON_9615
5) MY_dlink_wi-fi
6) 2kom-234
7) Tenda_067638

    wifisetup list

    oot@Omega-B8B3:/# wifisetup list
{

        "results": [
 {

        "ssid": "Why-Fi",
        "encryption": "WPA2PSK",
        "password": "PASSWORD"
}
]
}

    uci show wireless

    root@Omega-B8B3:/# uci show wireless
wireless.ra0=wifi-device
wireless.ra0.type='ralink'
wireless.ra0.mode='9'
wireless.ra0.channel='auto'
wireless.ra0.txpower='100'
wireless.ra0.ht='20'
wireless.ra0.country='RU'
wireless.ra0.countryregion='1'
wireless.ra0.disabled='0'
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='ra0'
wireless.@wifi-iface[0].network='wlan'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].key='12345678'
wireless.@wifi-iface[0].ApCliAuthMode='WPA2PSK'
wireless.@wifi-iface[0].ApCliEncrypType='AES'
wireless.@wifi-iface[0].ssid='Omega-B8B3'
wireless.@wifi-iface[0].ApCliSsid='Why-Fi'
wireless.@wifi-iface[0].ApCliPassWord='PASSWORD'
wireless.@wifi-iface[0].ApCliEnable='0'
wireless.@wifi-config[0]=wifi-config
wireless.@wifi-config[0].ssid='Why-Fi'
wireless.@wifi-config[0].encryption='WPA2PSK'
wireless.@wifi-config[0].key='PASSWORD'

    uci show network

    root@Omega-B8B3:/# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd1d:48c4:7633::/48'
network.wlan=interface
network.wlan.type='bridge'
network.wlan.ifname='eth0.1'
network.wlan.proto='static'
network.wlan.ipaddr='192.168.3.1'
network.wlan.netmask='255.255.255.0'
network.wlan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth0'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'

    cat /etc/config/wireless

    root@Omega-B8B3:/# cat /etc/config/wireless

config wifi-device 'ra0'
        option type 'ralink'
        option mode '9'
        option channel 'auto'
        option txpower '100'
        option ht '20'
        option country 'RU'
        option countryregion '1'
        option disabled '0'

config wifi-iface
        option device 'ra0'
        option network 'wlan'
        option mode 'ap'
        option encryption 'psk2'
        option key '12345678'
        option ApCliAuthMode 'WPA2PSK'
        option ApCliEncrypType 'AES'
        option ssid 'Omega-B8B3'
        option ApCliSsid 'Why-Fi'
        option ApCliPassWord 'PASSWORD'
        option ApCliEnable '0'

config wifi-config
        option ssid 'Why-Fi'
        option encryption 'WPA2PSK'
        option key 'PASSWORD'
    0
  • D

    Hi, I too have this problem. Brand new Omega2+ out of the box; unable to connect to Microtik CRS109-8G-1S-2HnD router wifi 2GHz b/g/n 20/40MHz HT Above, channel 3+7 (mixed-mode).

    I used my ethernet attachment and a network bridge to update it- the behavior is still present in 0.1.7 b139

    root@Omega-76EB:~# wifisetup
Onion Omega Wifi Setup

Select from the following:
1) Scan for Wifi networks
2) Type network info
q) Exit

Selection: 1
Scanning for wifi networks...

Select Wifi network:
--snip--
4) nnnn
--snip--
Selection: 4
Network: nnnn
Authentication type: WPA2PSK
Enter password: REDACTED

> Restarting wifimanager for changes to take effect
root@Omega-76EB:~#


root@Omega-76EB:~# wifisetup list
{ "results": [ { "ssid": "nnnn", "encryption": "WPA2PSK", "password": "REDACTED" } ] }


root@Omega-76EB:~# uci show wireless
wireless.ra0=wifi-device
wireless.ra0.type='ralink'
wireless.ra0.mode='9'
wireless.ra0.channel='auto'
wireless.ra0.txpower='100'
wireless.ra0.ht='20'
wireless.ra0.country='US'
wireless.ra0.disabled='0'
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='ra0'
wireless.@wifi-iface[0].network='wlan'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].ssid='Omega-76EB'
wireless.@wifi-iface[0].key='12345678'
wireless.@wifi-iface[0].ApCliAuthMode='WPA2PSK'
wireless.@wifi-iface[0].ApCliEncrypType='AES'
wireless.@wifi-iface[0].ApCliSsid='nnnn'
wireless.@wifi-iface[0].ApCliPassWord='REDACTED'
wireless.@wifi-iface[0].ApCliEnable='0'
wireless.@wifi-config[0]=wifi-config
wireless.@wifi-config[0].ssid='whargarbl'
wireless.@wifi-config[0].encryption='WPA2PSK'
wireless.@wifi-config[0].key='REDACTED'


root@Omega-76EB:~# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd1d:48c4:7633::/48'
network.wlan=interface
network.wlan.type='bridge'
network.wlan.ifname='eth0.1'
network.wlan.proto='static'
network.wlan.ipaddr='192.168.3.1'
network.wlan.netmask='255.255.255.0'
network.wlan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'


oot@Omega-76EB:~# cat /etc/config/wireless

config wifi-device 'ra0'
	option type 'ralink'
	option mode '9'
	option channel 'auto'
	option txpower '100'
	option ht '20'
	option country 'US'
	option disabled '0'

config wifi-iface
	option device 'ra0'
	option network 'wlan'
	option mode 'ap'
	option encryption 'psk2'
	option ssid 'Omega-76EB'
	option key '12345678'
	option ApCliAuthMode 'WPA2PSK'
	option ApCliEncrypType 'AES'
	option ApCliSsid 'nnnn'
	option ApCliPassWord 'REDACTED'
	option ApCliEnable '0'

config wifi-config
	option ssid 'nnnn'
	option encryption 'WPA2PSK'
	option key 'REDACTED'
    0
  • Zogg Baubas

    Bumping. Same issue with

    Device Firmware Version: 0.1.7 b139

    0 L 1 Reply
  • L

    @Zogg-Baubas , try the newer image file:
    http://repo.onion.io/omega2/images/
    Check out in manual how to update manually in terminal.

    -1 Zogg Baubas 1 Reply
  • X

    Same issue for me as well.

    Omega2+
    Exp dock

    Device Firmware Version: 0.1.7 b140

    root@Omega-C5A3:~# wifisetup
Onion Omega Wifi Setup

Select from the following:
1) Scan for Wifi networks
2) Type network info
q) Exit

Selection: 1
Scanning for wifi networks...

Select Wifi network:
1) foo
2) bar
3) baz

Selection: 3
Network: baz
Authentication type: WPA2PSK
Enter password: redacted

> Restarting wifimanager for changes to take effect
root@Omega-C5A3:~# 

    root@Omega-C5A3:~# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd1d:48c4:7633::/48'
network.wlan=interface
network.wlan.type='bridge'
network.wlan.ifname='eth0.1'
network.wlan.proto='static'
network.wlan.ipaddr='192.168.3.1'
network.wlan.netmask='255.255.255.0'
network.wlan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth0'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'

    root@Omega-C5A3:~# uci show wireless
wireless.ra0=wifi-device
wireless.ra0.type='ralink'
wireless.ra0.mode='9'
wireless.ra0.channel='auto'
wireless.ra0.txpower='100'
wireless.ra0.ht='20'
wireless.ra0.country='US'
wireless.ra0.disabled='0'
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='ra0'
wireless.@wifi-iface[0].network='wlan'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].key='12345678'
wireless.@wifi-iface[0].ApCliAuthMode='WPA2PSK'
wireless.@wifi-iface[0].ApCliEncrypType='AES'
wireless.@wifi-iface[0].ssid='Omega-C5A3'
wireless.@wifi-iface[0].ApCliSsid='baz'
wireless.@wifi-iface[0].ApCliPassWord='redacted'
wireless.@wifi-iface[0].ApCliEnable='0'
wireless.@wifi-config[0]=wifi-config
wireless.@wifi-config[0].ssid='baz'
wireless.@wifi-config[0].encryption='WPA2PSK'
wireless.@wifi-config[0].key='redacted'
    0
  • Zogg Baubas

    @Luciano-S. Manual sysupgrade does not work:

    root@Omega-6D3B:/# sysupgrade -v --force /omega2p-v0.1.7-b140.bin 
Saving config files...
etc/config/dhcp
etc/config/dropbear
etc/config/firewall
etc/config/mountd
etc/config/network
etc/config/onion
etc/config/rpcd
etc/config/system
etc/config/ubootenv
etc/config/uhttpd
etc/config/wireless
etc/dropbear/dropbear_rsa_host_key
etc/fw_env.config
etc/group
etc/hosts
etc/inittab
etc/opkg/keys/1afebb2008639538
etc/opkg/keys/2ea9a9bc60cbc099
etc/opkg/keys/60366ca0eb621637
etc/opkg/keys/6405feca1ff7d881
etc/opkg/keys/72a57f2191b211e0
etc/opkg/keys/7afde20b15076f21
etc/opkg/keys/9ef4694208102c43
etc/opkg/keys/b5043e70f9a75cde
etc/opkg/keys/dace9d4df16896bf
etc/opkg/keys/dd6de0d06bbd3d85
etc/passwd
etc/profile
etc/rc.local
etc/shadow
etc/shells
etc/sysctl.conf
etc/sysctl.d/local.conf
root/.config/htop/htoprc
killall: watchdog: no process killed
Sending TERM to remaining processes ... onion-helper udhcpc dnsmasq mountd ntpd ubusd askfirst logd rpcd netifd odhcpd uhttpd device-client avahi-daemon 
Sending KILL to remaining processes ... askfirst 
Switching to ramdisk...
Performing system upgrade...
Could not get image magic
Image check failed.
Upgrade completed
Rebooting system...
umount: can't unmount /dev/pts: Resource busy
umount: can't unmount /dev: Resource busy

    And the Omega boots into the old image:

    @arte ➜  Zemeplytis rvm:(system)  ssh root@Omega-6D3B.local
root@omega-6d3b.local's password: 


BusyBox v1.25.1 () built-in shell (ash)

   ____       _             ____
  / __ \___  (_)__  ___    / __ \__ _  ___ ___ ____ _
 / /_/ / _ \/ / _ \/ _ \  / /_/ /  ' \/ -_) _ `/ _ `/
 \____/_//_/_/\___/_//_/  \____/_/_/_/\__/\_, /\_,_/
 W H A T  W I L L  Y O U  I N V E N T ? /___/
 -----------------------------------------------------
   Ω-ware: 0.1.7 b139
 -----------------------------------------------------
    0 Lazar Demin 1 Reply
  • Lazar Demin
    administrators

    @Zogg-Baubas yikes! why the --force flag??

    0 K Zogg Baubas 2 Replies
  • K

    @Lazar-Demin said in Omega2+ fails to connect to wifi:

    @Zogg-Baubas yikes! why the --force flag??

    Hey, Administrators, when will you resolve the wifi connectivity issues that we're talking about on this thread?

    1
  • Zogg Baubas

    @Lazar-Demin said in Omega2+ fails to connect to wifi:

    @Zogg-Baubas yikes! why the --force flag??

    Because without it I'v got the same result. Figured, as this particular Omega was useless in this state, it couldn't get worse even if bricked. In the end '--force' didnt achieve anything that unforced version didnt.

    0 K WereCatf 2 Replies
  • K

    @Zogg-Baubas It seems that we have to find the solution by ourselves, the Admins do not help at all.
    Have you tried the new version of firmware?

    0
  • WereCatf

    @Zogg-Baubas I already instructed you in http://community.onion.io/topic/1178/wifi-connection-problem-with-omega2/21 how to flash the image correctly.

    0
  • X

    @Kostas-David - I tried omega2p-v0.1.8-b145.bin and still no luck getting the wi-fi working yet. I'm using a Mikrotik router and I've never had any issues with other devices.

    0 K 1 Reply
  • G

    I had also connection problems because i had special characters in my wlan password! After the upgrade of the firmware it also works with special letters!

    0 A 1 Reply
  • K

    @xmatt I also confirm that upgrading the firmware didn't help.
    @Gerald-Schalek my wlan password does not container special characters but the wifi does not connect

    0
  • K

    Status update: By installing firmware omega2p-v0.1.8-b145.bin I managed to get connected to my Android phone's mobile hotspot with no security.
    Problems:

    1. Omega cannot get connected to Access points with security enabled (WPA, WPA2 etc)
    2. No access to cloud, it is shown as "Offline"
    3. LED is constantly blinking, even after restart
    4. No internet access from the SSH terminal
    5. Sometimes there is internet access from Console (it checks for new firmware successfully.

    Still unusable...

    1
  • K

    Hello, I would like to share my progress. I finally managed to connect Omega2 to my router. The problem was the encryption type. My router uses "TKIP" but Omega2 has "AES".

    So, I entered the following:

    uci set wireless.@wifi-iface[0].ApCliEncrypType=TKIP
    uci commit wireless
    etc/init.d/network restart

    Note: The firmware I am using is 0.1.7 b139 because for some strange reason the firmware update downloads this version instead of 0.1.8. But it works

    1
  • M

    Hi,

    I had the same problem but I solved it. Here's how i did:

    1. connect to your Omega2
    2. list APs with this command: aps
    root@Omega-XXXX:~# aps
WRTnode AP scaner.
Begin scaning APs, pls wait...
Finished.
APs available are...
ra0       get_site_survey:
Ch  SSID   BSSID               Security         Signal(%) W-Mode  ExtCH  NT
...
10  MyAP   02:6f:d7:3e:8e:60   WPAPSK/TKIPAES   50        11b/g/n NONE   In
...

    This command give you more information about your AP. The most important is Security.

    1. Take this conversion table to modify your /etc/config/wireless config file:
    aps:Security            vw:ApCliAuthMode/ApCliEncrypType
=========================================================
WPA1PSKWPA2PSK/TKIPAES	WPA2PSK/AES
WPA2PSK/AES		WPA2PSK/AES
WPA2PSK/TKIP		WPA2PSK/TKIP
WPAPSK/TKIPAES		WPAPSK/TKIP
WPAPSK/AES		WPAPSK/AES
WPAPSK/TKIP		WPAPSK/TKIP
WEP			WEP/WEP

    Before edit it, my /etc/config/wireless contained:

    config wifi-device 'ra0'
	option type 'ralink'
	option mode '9'
	option channel 'auto'
	option txpower '100'
	option ht '20'
	option country 'US'
	option disabled '0'

config wifi-iface
	option device 'ra0'
	option network 'wlan'
	option mode 'ap'
	option encryption 'psk2'
	option key '12345678'
	option ApCliEncrypType 'TKIP'
	option ApCliSsid 'MyAP'
	option ApCliPassWord 'xxxxxxxx'
	option ssid 'Omega-xxxx'
	option ApCliEnable '1'

config wifi-config
	option ssid 'MyAP'
	option encryption 'WPA1PSK'
	option key 'xxxxxxxx'

    With convertion table, i edited it like this:

    config wifi-device 'ra0'
	option type 'ralink'
	option mode '9'
	option channel 'auto'
	option txpower '100'
	option ht '20'
	option country 'US'
	option disabled '0'

config wifi-iface
	option device 'ra0'
	option network 'wlan'
	option mode 'ap'
	option encryption 'psk2'
	option key '12345678'
	option ApCliEncrypType 'TKIP'
	option ApCliSsid 'MyAP'
	option ApCliPassWord 'xxxxxxxx'
	option ssid 'Omega-xxxx'
	option ApCliEnable '1'

config wifi-config
	option ssid 'MyAP'
	option encryption 'WPAPSK'
	option key 'xxxxxxxx'

    (I modified option encryption 'WPA1PSK' -> option encryption 'WPAPSK' in config wifi-config section)

    1. To finish, restart network:
    root@Omega-xxxx:/etc/config# nr
    1. After some time, you can reconnect to your Omega and verify if you have an IP:
    root@Omega-xxxx:~# ia
apcli0    Link encap:Ethernet  HWaddr 42:A3:6B:00:BE:3B
          inet addr:192.168.1.16  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::40a3:6bff:fe00:be3b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:265 errors:0 dropped:0 overruns:0 frame:0
          TX packets:281 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:74379 (72.6 KiB)  TX bytes:25424 (24.8 KiB)
    1. You can continue with Onion Setup Wizard web interface (http://omega-xxxx.local/) if you want

    ps: after network restart, i checked my /etc/config/wireless, and i saw that a new line was added in config wifi-iface section: option ApCliAuthMode 'WPAPSK':

    config wifi-device 'ra0'
	option type 'ralink'
	option mode '9'
	option channel 'auto'
	option txpower '100'
	option ht '20'
	option country 'US'
	option disabled '0'

config wifi-iface
	option device 'ra0'
	option network 'wlan'
	option mode 'ap'
	option encryption 'psk2'
	option key '12345678'
	option ApCliEncrypType 'TKIP'
	option ApCliSsid 'MyAP'
	option ApCliPassWord 'xxxxxxxx'
	option ssid 'Omega-xxxx'
	option ApCliEnable '1'
	option ApCliAuthMode 'WPAPSK'

config wifi-config
	option ssid 'MyAP'
	option encryption 'WPAPSK'
	option key 'xxxxxxxx'

    Hope this help you.

    8 K Lazar Demin T B M 5 Replies
  • K

    @Mikaël-PIRIO After trying everything else, only this worked. Thanks for putting in time for this answer.

    2
omega2+ 335 wifi 271 setup 47 wifi fails 31 connectivity 13
Log in to reply
 

Looks like your connection to Community was lost, please wait while we try to reconnect.