Connecting the USB-Еthernet adapter to Omega2+

CAP 33

Hello. I need connect a USB-Ethernet adapter to my Omega2+. I use adapter on chip RTL8153.
The Raspberry Pi3 detects the new interface, but the Omega2 does not.
I installed the packages kmod-usb-net-rtl8152 and kmod-usb-net.
Tell me, can I somehow make my Omega2 see this adapter? Maybe someone has already done this, which adapter model you used.

crispyoz

@CAP-33 Can you post the log showing 1) when you insert the USB adapter; 2) insmod kmod-usb-net-rtl8152 3) insmod kmod-usb-net; 4) ifconfig

CAP 33

@crispyoz
ifconfig

apcli0    Link encap:Ethernet  HWaddr 40:A3:6B:C7:31:F3
          inet addr:192.168.1.103  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::42a3:6bff:fec7:31f3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

br-wlan   Link encap:Ethernet  HWaddr 40:A3:6B:C7:31:F1
          inet addr:192.168.3.1  Bcast:192.168.3.255  Mask:255.255.255.0
          inet6 addr: fd1d:48c4:7633::1/60 Scope:Global
          inet6 addr: fe80::42a3:6bff:fec7:31f1/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:2301 (2.2 KiB)

eth0      Link encap:Ethernet  HWaddr 40:A3:6B:C7:31:F2
          inet addr:192.168.1.102  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::42a3:6bff:fec7:31f2/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:112 errors:0 dropped:0 overruns:0 frame:0
          TX packets:114 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:23294 (22.7 KiB)  TX bytes:16976 (16.5 KiB)
          Interrupt:5

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:36 errors:0 dropped:0 overruns:0 frame:0
          TX packets:36 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:3661 (3.5 KiB)  TX bytes:3661 (3.5 KiB)

ra0       Link encap:Ethernet  HWaddr 40:A3:6B:C7:31:F1
          inet6 addr: fe80::42a3:6bff:fec7:31f1/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:6

insmod kmod-usb-net-rtl8152

Failed to find kmod-usb-net-rtl8152. Maybe it is a built in module ?

insmod kmod-usb-net

Failed to find kmod-usb-net. Maybe it is a built in module ?

When I insert the USB adapter

 usb 1-1: new high-speed USB device number 2 using ehci-platform

When I remove the USB adapter

usb 1-1: USB disconnect, device number 2

CAP 33

@crispyoz
I bought another adapter with ASIX AX88179A chip.
Reinstalled the following modules:
kmod-mii
kmod-usb-net
kmod-usb-net-asix

root@Omega-31F1:~# modprobe asix
asix is already loaded
root@Omega-31F1:~# modprobe usbnet
usbnet is already loaded
root@Omega-31F1:~# modprobe mii
mii is already loaded

Command dmesg | grep usbcore printed following:
root@Omega-31F1:/etc/modules.d# dmesg | grep usbcore
[ 5.391249] usbcore: registered new interface driver usbfs
[ 5.396990] usbcore: registered new interface driver hub
[ 5.402486] usbcore: registered new device driver usb
[ 5.801747] usbcore: registered new interface driver usb-storage
[ 17.632985] usbcore: registered new interface driver btusb
[ 17.643265] usbcore: registered new interface driver cdc_acm
[ 17.905698] usbcore: registered new interface driver ums-alauda
[ 17.914983] usbcore: registered new interface driver ums-cypress
[ 17.924496] usbcore: registered new interface driver ums-datafab
[ 17.933704] usbcore: registered new interface driver ums-freecom
[ 17.943042] usbcore: registered new interface driver ums-isd200
[ 17.955095] usbcore: registered new interface driver ums-jumpshot
[ 17.964453] usbcore: registered new interface driver ums-karma
[ 17.974610] usbcore: registered new interface driver ums-sddr09
[ 17.984034] usbcore: registered new interface driver ums-sddr55
[ 17.993874] usbcore: registered new interface driver ums-usbat
[ 18.007211] usbcore: registered new interface driver usbhid
[ 18.026860] usbcore: registered new interface driver usblp
[ 18.067654] usbcore: registered new interface driver usbserial
[ 18.073744] usbcore: registered new interface driver usbserial_generic
[ 18.154428] usbcore: registered new interface driver asix
[ 18.162642] usbcore: registered new interface driver ch341
[ 18.177852] usbcore: registered new interface driver cp210x
[ 18.193761] usbcore: registered new interface driver ftdi_sio
[ 18.222649] usbcore: registered new interface driver pl2303
[ 18.268377] usbcore: registered new interface driver snd-usb-audio
[ 18.293507] usbcore: registered new interface driver uvcvideo
[ 18.310592] usbcore: registered new interface driver option

The problem is still not solved. Omega does not see the interface.
Maybe this is due to the fact that the adapter has a USB 3.0 interface?