Posts made by Paolo Moro

Thanks! Many Thanks

@DumTux I can't do it I have to log in first. Perhaps the serial port or the ethernet card is active.

Thanks for your advice.
But I believe that at least the serial port is active.

I'm trying a MT7628N Chipset with MIPS24KEc Kernel.

I will try with the serial port.

Hi all, I tried to upload this image openwrt-22.03.3-ramips-mt76x8-onion_omega2p-squashfs-sysupgrade.bin

then sysupgrade /tmp/ope...

I don't see the WiFi network, is this normal? Can I connect by another way? With the hard reset nothing append.

@luz very interesting. Thank you for the contribution.
I did the same thing. But with a different logic.

• Run the "master" board
• every minute she try, by wifi, to connect to an omega-... connect on ssh (with key accept by default yes) without sshpass.
• After a successful connection ssh she inject a script that downloads the .bin from a repository on the LAN and starts the sysupgrade.
  (by wifi)

I tested it with 100pz in 2 houres, all automatic. I can create many masters... and do everything faster.

But my version is sh + python script

Onion Omega2+ is the best! €€€

Thanks!!!!! I need to use an ONION OMEGA to setup the other ONION OMEGA!!
I need to install sshpass on Onion.

https://www.devdungeon.com/content/python-ssh-tutorial

What do you think about?

@crispyoz said in Script to deploy firmware to device using ethernet ipv6:

sshpass

Hi Thanks for you script. Can you tell me how to install sshpass? Please? THk

Hello to all,
has anyone ever used vnstat package? Is there any information for the onion version?

Or may be an alternative?

I need to calculate the daily megabite consumption for an Internet connection.

Thanks

Re: receive keystrokes from a usb keyboard

| Note: Remember that the ATmega runs on 5V, and therefore it reads 5V as logical high.

I use a classic NFC reader PNR532 V3 (like: https://images.app.goo.gl/uouKyD4WnnLDmuhHA) - SPI connection.

I used a lots of that reader connected directly on 5V of the omega PINOUT (expansion header) with ARDUINO DOCK 2 with onion board.

Now I bought 100 new NFC reader and if I connect them on an ARDUINO UNO everything work very good, but if I use the Onion Power on the ARDUINO DOCK 2 (5V) they don't work fine.

I noticed two thing:

1. with the 3,3V of the expansion header the new readers works good
2. these new reader are more powerfull, the reading range is wider.

Is the 5V power of the ARDUINO DOCK different from the real Arduino UNO?

many many thanks!!!

Paolo

@György-Farkas said in Wifi LAN Active - how to know:

You can change the priority with the wifisetup priority -ssid <ssid> -move <up|down|top> command.

Thank-you very much

I noticed the section config wifi-iface 'sta', bu when I use the command line
wifisetup add -ssid $SSID -encr $ENC -password $PasskeyWifi

is there the possibility to force then specific $SSID?

config wifi-iface 'sta'
option device 'radio0'
option mode 'sta'
option ifname 'apcli0'
option encryption 'psk2'
option network 'wwan'
option disabled '0'
option key 'mywifi'
option ssid 'xxxx'

Is there the possibility to know which wifi LAN the OMEGA2 is using?

or a specific information to read in some file like?
vi /etc/config/wireless

Thank-you!!
Paolo Moro

Tank-you @Douglas-Kryder do you know the right package repos I have to insert into the file:

/etc/opkg/distfeeds.conf

Because if I try the command:
opkg install ipset

Response:
opkg_install_cmd: Cannot install package ipset.

Thanks in advance.

Hi,
I tried to connect my omega2 with this guide https://onion.io/2bt-using-hologram-expansion/.

I'm using ArduinoDock. When I tried to restart the firewall with
/etc/init.d/firewall restart

I received an error

Warning: Unable to locate ipset utility, disabling ipset support
Warning: Section @zone[2] (cellular) cannot resolve device of network 'hologram'
Warning: Section @zone[2] (cellular) has no device, network, subnet or extra options

• Flushing IPv4 filter table
  ...

Is there an alternative guide? or Where is the problem?

Thank-you.

Paolo