1. Home
  2. Omega Talk
  3. installing an ipk package and incompatible with the architecture error

installing an ipk package and incompatible with the architecture error

  • C

    @optech @tjoseph1 is correct, this ipk is mispackaged. An IPK is just a set of tgz inside a tgz, so you can extract the files and run the binary and the error becomes self-evident. Best to contact the author or recompile the code.

    0
  • optech

    I have the sources here:
    https://www.chirpstack.io/gateway-bridge/community/source/

    I recompiled it but it compiles as big endian as you said. So do you think is there a way to compile as little endian?

    By the way, i also ask this issue to author in chirpstack community forum. no answer yet.

    0 T 1 Reply
  • T

    @optech

    mipsel ipk is here:
    https://disk.yandex.com/d/bDtdR4j251cKIQ
    Filename: chirpstack-gateway-bridge_3.11.0_mipsel_24kc.ipk

    I couldn't find the "3.11.0-r1" in the github repo
    ..
    v3.1.0
    v3.10.0
    v3.10.0-test.1
    v3.11.0
    v3.11.0-test.1
    v3.2.0
    ..
    so, I picked 3.11.0

    omega# /etc/init.d/chirpstack-gateway-bridge status
    Syntax: /etc/init.d/chirpstack-gateway-bridge [command]
    Available commands:
    start Start the service
    stop Stop the service
    restart Restart the service
    reload Reload configuration files (or restart if service does not implement reload)
    enable Enable service autostart
    disable Disable service autostart

    Thanks.

    0 optech 2 Replies
  • optech

    @tjoseph1 Thank you for packing for me šŸ™‚ the information you gave me was useful.. Thanks again...

    0
  • optech

    @tjoseph1 I tried to run follows:

    /etc/init.d/chirpstack-gateway-bridge enable

    /etc/init.d/chirpstack-gateway-bridge start

    It says "Starting chirpstack-gateway-bridge" but there is no start an instance as proccess.. Could you had a chance to test it on Omega after compiling?

    0
  • C

    @optech Type logread and see what the service is reporting.

    0 optech 1 Reply
  • optech

    @crispyoz said in installing an ipk package and incompatible with the architecture error:

    logread

    I did but nothing about chirpstack gateway bridge

    0
  • C

    @optech add PROCD_DEBUG=1 to the top of your init script to log more info about the process

    0 optech 1 Reply
  • optech

    @crispyoz

    I did it but still there is nothing about chirpstack gateway bridge ! šŸ˜•

    0
  • C

    @optech Post your init script please, it will log whatever the script results are. Check the log again using:

    logread | grep -i chirpstack

    0
  • T

    I downloaded the file again from yandex drive and installed. Pls see below.

    Omega# # onion os version
    === Version Info ===
    Omega firmware: v0.3.3 b247
    onion-os - 1.0.6-1

    Omega# opkg install ./chirpstack-gateway-bridge_3.11.0_mipsel_24kc.ipk
    Installing chirpstack-gateway-bridge (3.11.0) to root...
    Configuring chirpstack-gateway-bridge.

    Omega# opkg files chirpstack-gateway-bridge
    Package chirpstack-gateway-bridge (3.11.0) is installed on root and has the following files:
    /etc/init.d/chirpstack-gateway-bridge
    /opt/chirpstack-gateway-bridge/LICENSE
    /opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge
    /etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml
    /opt/chirpstack-gateway-bridge/README.md

    Omega# free
    total used free shared buffers cached
    Mem: 124784 56492 68292 72 5536 28884
    -/+ buffers/cache: 22072 102712

    Omega# /etc/init.d/chirpstack-gateway-bridge start
    Starting chirpstack-gateway-bridge

    Omega# free
    total used free shared buffers cached
    Mem: 124784 58644 66140 76 5536 28892
    -/+ buffers/cache: 24216 100568

    Omega# ps
    2092 root 658m S /opt/chirpstack-gateway-bridge/chirpstack-gateway-br

    Omega# logread
    Mon Feb 22 22:35:13 2021 user.info chirpstack-gateway-bridge[2092]: time="2021-02-22T22:35:13.255502795Z" level=info msg
    ="starting ChirpStack Gateway Bridge" docs="https://www.chirpstack.io/gateway-bridge/" version=3.11.0
    Mon Feb 22 22:35:13 2021 user.info chirpstack-gateway-bridge[2092]: time="2021-02-22T22:35:13.257726475Z" level=info msg
    ="backend/semtechudp: starting gateway udp listener" addr="0.0.0.0:1700"
    Mon Feb 22 22:35:13 2021 user.warn chirpstack-gateway-bridge[2092]: time="2021-02-22T22:35:13.268847616Z" level=warning
    msg="[store] memorystore wiped" module=mqtt
    Mon Feb 22 22:35:13 2021 user.info chirpstack-gateway-bridge[2092]: time="2021-02-22T22:35:13.269861713Z" level=info msg
    ="integration/mqtt: connected to mqtt broker"

    Omega# netstat -atunp
    Active Internet connections (servers and established)
    Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
    tcp 0 0 0.0.0.0:1883 0.0.0.0:* LISTEN 1610/mosquitto
    tcp 0 0 127.0.0.1:51116 127.0.0.1:1883 ESTABLISHED 2092/chirpstack-gat
    tcp 0 0 127.0.0.1:1883 127.0.0.1:51116 ESTABLISHED 1610/mosquitto
    tcp 0 0 :::9001 :::* LISTEN 1610/mosquitto
    udp 0 0 :::1700 :::* 2092/chirpstack-gat

    Omega# /etc/init.d/chirpstack-gateway-bridge stop
    Stopping chirpstack-gateway-bridge
    stopped process in pidfile '/var/run/chirpstack-gateway-bridge.pid' (pid 2092)

    Omega# netstat -atunp
    Active Internet connections (servers and established)
    Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
    tcp 0 0 0.0.0.0:1883 0.0.0.0:* LISTEN 1610/mosquitto
    tcp 0 0 127.0.0.1:1883 127.0.0.1:51116 TIME_WAIT -
    tcp 0 0 :::9001 :::* LISTEN 1610/mosquitto

    0 optech 1 Reply
  • optech

    @tjoseph1

    root@OpenWrt:/# opkg files chirpstack-gateway-bridge
Package chirpstack-gateway-bridge (3.11.0) is installed on root and has the following files:
/etc/init.d/chirpstack-gateway-bridge
/opt/chirpstack-gateway-bridge/LICENSE
/opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge
/etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml
/opt/chirpstack-gateway-bridge/README.md
root@OpenWrt:/# free
              total        used        free      shared  buff/cache   available
Mem:         124860       14664       96916         312       13280       79712
Swap:             0           0           0
root@OpenWrt:/# /etc/init.d/chirpstack-gateway-bridge start
Starting chirpstack-gateway-bridge
root@OpenWrt:/# free
              total        used        free      shared  buff/cache   available
Mem:         124860       14668       96912         312       13280       79708
Swap:             0           0           0

    root@OpenWrt:/# ps | grep chirpstack
2048 root      1212 S    grep chirpstack

    root@OpenWrt:/# logread | grep chirpstack
root@OpenWrt:/#

    What could be the reason of this difference? what do you think? By the way, i loaded a custom build openwrt firmware 19.07.. Is that can be the reason?

    0 T 1 Reply
  • T

    @optech
    "a custom build openwrt firmware 19.07 ..Is that can be the reason"
    May be..

    You could flash the omega2 with onion build and try. I have provided my onion os version; any recent version should work.

    "/opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge" is the only "arch dependent" (binary) file in the ipk.

    $ file build/chirpstack-gateway-bridge
    build/chirpstack-gateway-bridge: ELF 32-bit LSB executable, MIPS, MIPS32 version 1 (SYSV), statically linked, Go BuildID=0A8....

    You can also try running it from command prompt using the options that "/etc/init.d/chirpstack-gateway-bridge" script uses with "start" parameter.

    ("/etc/chirpstack-gateway-bridge/chirpstack-gateway-bridge.toml" contains the settings, it seems)

    Thank you.

    0 optech 1 Reply
  • optech

    @tjoseph1 thank you very much for your help.
    I loaded onion build firmware and tried it again then it works. šŸ™‚

    But it doesn't work on openwrt 19.07 custom build.. I really wonder what would be the reason of this issue?

    Here is the build which chirpstack gateway bridge doesnt work on..:
    https://drive.google.com/file/d/1i5PeBWMF-9kke3xLXnlwJIylrfxVHWhm/view?usp=sharing

    0
  • T

    @optech
    Can you pls replace the /opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge in your openwrt 19.07 with this file:
    https://disk.yandex.com/d/C_6-fmcDtqXIGA and then try running it?

    It is a zip file, that unzips to "chirpstack-gateway-bridge" exe.

    Thank you.

    0 optech 1 Reply
  • optech

    @tjoseph1 Thank you for your help. I was on a vacation sorry for late...

    I replaced "/opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge" with the file that you sent. But result is same, dont work and so no ram change(on openwrt 19.07)..
    Do you have another idea to find the reason of this issue?

    0
  • optech

    I recompiled chirpstack gateway bridge as following the steps below:

    export GOARCH=mipsle
export GOOS=linux
make build

    root@OpenWrt:~# file /opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge

/opt/chirpstack-gateway-bridge/chirpstack-gateway-bridge: ELF 32-bit LSB executable, MIPS, MIPS32 version 1 (SYSV), statically linked, Go BuildID=VcvuifmDnNysO-WpZUz5/FGFca5Lt5vpptRtlLTBo/l2QuqgekGwKVygyjsXAL/6lmuYGmDGU2RDGrxxamU, stripped

    The result is the same doesn't work on openwrt 19.07...

    0 T 1 Reply
  • T

    @optech
    Ok. Let us start simple.
    Are you able to cross-compile the "hello_world.go" and run it in the 19.07 Omega2 with GOARCH,GOOS parameters set as above ?

    package main
    import "fmt"
    func main() {
    fmt.Println("Hello, World!")
    }

    If not, you may want to try GOMIPS=softfloat or some other options in addition to those two. Once that thing prints \"Hello, World!\", try the same options to build chirpstack-gateway-bridge.

    Thanks.

    0 optech 1 Reply
  • optech

    @tjoseph1 Thank you again for your help.

    I compiled the hello world go app as following...:

    export GOARCH=mipsle
export GOOS=linux
export GOMIPS=softfloat
go build hello.go

    if i dont use "GOMIPS=softfloat", it works on openWRT 18.06 but dont work on openWRT 19.07 as giving following error:

    root@OpenWrt:~# ./hello
Illegal instruction

    with "GOMIPS=softfloat" option, it works on openWRT 19.07..

    But after seeing that, i compiled chirpstack-gateway-bridge app with same options. But it still doesnt work on openWRT 19.07 šŸ˜ž

    chirpstack-gateway-bridge$ export GOARCH=mipsle
chirpstack-gateway-bridge$ export GOOS=linux
chirpstack-gateway-bridge$ export GOMIPS=softfloat
chirpstack-gateway-bridge$ make build

    i feel near to solution but i have no idea for now.

    0 optech T 2 Replies
  • optech

    @optech by the way, i first setup the chirpstack-gateway-bridge ipk file which you sent before, then i replace the exe in opt/chirpstack-gateway-bridge with i compiled. then it didnt work on openwrt 19.07

    0
omega2s+ 96 ipk 5 architecture 1
Log in to reply
 

Looks like your connection to Community was lost, please wait while we try to reconnect.