1. Home
  2. Omega Talk
  3. Arduino Dock guide is up

Arduino Dock guide is up

  • M

    I just tried flashing the bootloader using the mini Dock by trying to wedge some stripped ends of a few Jumper cables (exposed copper strands inserted in the female headers of the minidock and then insert the Omega into the female headers "pinching" the copper strands of each particular wire into the specific female headers.) And usb powering both the arduino dock and the onion on the mini dock independently. But got an error when trying to flash via ssh terminal (using sh /usr/bin/arduino-dock flash bootloader). (Error said rc:-1)

    14479982448050.jpg 14479982448161.jpg 14479982448252.jpg

    Not sure if there's a way to get 5v directly to the Arduino Dock via the mini Dock or if I have to maybe externally power the Arduino Dock using Jumper cables.

    Here's a screenshot of the error which maybe hinting that the connection didn't work (maybe the wires I used didn't make a good connection when I sandwiched them between the mini dock and the Omega pins?)

    Screenshot_20151120-005940-01.jpeg

    0
  • K

    @Maurice Difficult to tell from the photos, but it looks like you only have 4 wires connected though the instructions say that there should be 6 connections
    Expansion Dock GPIO 1 -> Arduino Dock Pin 12
    Expansion Dock GPIO 6 -> Arduino Dock Pin 13
    Expansion Dock GPIO 7 -> Arduino Dock Reset Pin
    Expansion Dock GPIO 19 -> Arduino Dock Pin 11
    Expansion Dock GPIO 5V -> Arduino Dock 5V Pin
    Expansion Dock GPIO GND -> Arduino Dock GND Pin
    I may be mistaken, butit looks like there is no 5V or GND connections.

    Since I too only have a Mini Dock and no Expansion Dock, I am going to have to connect do something like you.
    I am concerned about the 5V connection, so my intention is to omit any 5V connection between the Mini Dock and the Arduino Dock. I will power each separately, but connect the GND between the two.
    Does anyone have any comments on this?

    (As an aside, hooking things up would be greatly assisted if we had access to schematics.
    HINT HINT HINT to the Omega people :))

    0 M 1 Reply
  • M

    @Kit-Bishop I tried to power the minidock and Arduino Dock separately using two different micro USB power sources. I'll have to try to powering the Arduino Dock via DC or directly on the female headers. (Ie I'll try not to use the mirco USB port on the Arduino Dock).

    0
  • M

    So I tried flashing both of the Arduino Docks that I received and the first Dock continued to give the error I put in the screenshot above.

    The second dock displayed progress bars but I received what looked like three different errors.

    On the first Dock the led flickers but the bootloader flash says fail. On the second dock the progress bars appeared but the flashing script said it could not recognize the device signature. The LED on the second dock shut off and didn't flicker. The script eventually went into safe mode....I hope I didn't fry both the boards. Yikes. (Some smoke appeared on one of the Arduino Docks : s)

    In any case here are some photos. Hope others learn from any mistakes I might have done in this attempt.

    Here are screens from the Console
    Screenshot_20151120-193113-01.jpeg

    Screenshot_20151120-193740-01.jpeg

    Screenshot_20151120-193834-01.jpeg

    Here are my attempts to wire the minidock

    14480696831133.jpg

    14480696830010.jpg

    14480696830211.jpg

    14480696834594.jpg

    14480696834685.jpg 14480696834756.jpg 14480696831032.jpg

    0
  • Lazar Demin
    administrators

    If you're using the Mini Dock, the Omega can be used to provide 3.3V to the Arduino Dock, just plug it into the 3V3 Pin. I'll update the wiki to include this info.

    @Maurice when establishing communication between two devices like this, it's very important that they share a common ground (as @Kit-Bishop mentioned). Otherwise, there is no "agreement" between the two devices as to what defines a low signal (a 0 in binary) and what defines a high signal (a 1 in binary). It's likely that the Arduino Dock and Omega are misunderstanding each other.
    Try running the 3.3V and GND to the Arduino Dock and trying again. Let me know how it goes!

    0
  • K

    I have a couple of questions in relation to all of this.
    First so you understand what I am currently doing:

    • I don't have an Expansion Dock I only have a Mini Dock and an Arduino Dock
    • I have an Adafruit PowerBoost Shield with 2000mAh Lithium battery
    • I plug the Omega in to the Arduino Dock
    • I plug the PowerBoost Shield in to the Arduino Dock
    • I only ever communicate with the Omega using WiFi
      Thus, always have power that can be switched on and off as required and no mess of cables everywhere:-)
      This all works without any problems and implies to me that the Omega is powered by the 3.3v from the Arduino Dock.

    First question:

    • Is this OK and safe?

    Next, I note in the instructions that once the Arduino Dock is set up, a sketch can be loaded on to the Arduino Dock using:

    • sh /usr/bin/arduino-dock flash <hex file>

    but for I note that for the initial set up:

    • this is basically the same as what we initially need to do to initially set up the Arduino Dock, i.e.:sh /usr/bin/arduino-dock flash bootloader
    • and there is no other communication between the two for setup

    These two together imply to me that when the Omega is plugged in to the Arduino Dock they are already connected as covered in the wiring instructions and that consequently no additional wiring is required and the whole procedure can be carried out without the separate wiring.
    So my second question:

    • Am I correct about this, or have I missed something?
    0 Lazar Demin 1 Reply
  • Lazar Demin
    administrators

    @Kit-Bishop Yep, what you're doing is safe and ok. You can also power the Omega + Arduino Dock with a micro usb. And when using the Arduino Dock you can only communicate with the Omega via WiFi (ssh and console) even when the micro usb is plugged in.

    The extra wires are only needed for the Inital Setup (now on it's own wiki page). Once you complete that, there is no need for any extra wires.

    The Omega can then use the Arduino Dock to flash the ATmega chip with Sketches. You can use the command you have above or you can use the Arduino IDE to wirelessly have the Omega flash the ATmega chip (probably the quicker option).

    1 M 1 Reply
  • K

    @Lazar-Demin Cool šŸ™‚ Thanks for the quick response

    0
  • R

    I'm getting a failure when I try to enter the password to upload the sketch. Error message is ash: merge-sketch-with-bootloader.lua: not found. I flashed the board and I thought is said it was ok. Ideas?

    Thanks,
    Russ

    0 Lazar Demin M 2 Replies
  • T

    I try to burn the bootloader, all my connections seems OK but I always have this message:

    root@onion:~# sh /usr/bin/arduino-dock flash bootloader
    Flashing bootloader...
    avrdude: AVR device not responding
    avrdude: initialization failed, rc=-1
    Double check connections and try again, or use -F to override
    this check.

    I double check connections, everything is fine. What can I do?

    0 Lazar Demin 1 Reply
  • M

    @Lazar-Demin just tried flashing the dock and it worked for one of the docks šŸ™‚ one of the docks continued to display the error.

    Screenshot_20151122-165507-01.jpeg

    For the dock that did work:
    I wired the dock as you suggested with 3.3v and GND wired to the dock.

    Function SPI MISO -> Mini Dock and Omega Pin 1 -> Arduino Dock Pin 12

    Function SPI SCK -> Mini Dock and Omega Pin 6 -> Arduino Dock Pin 13

    Function SPI RESET -> Mini Dock and Omega Pin 7 -> Arduino Dock Pin Reset

    Function SPI MOSI -> Mini Dock and Omega Pin 19 -> Arduino Dock Pin 11

    Function VCC -> Mini Dock and Omega Pin 3.3V -> Arduino Dock Pin 3.3V

    Function GND -> Mini Dock and Omega Pin GND -> Arduino Dock Pin GND

    Here are some photos of the wiring.

    14482301031241.jpg 14482301031190.jpg 14482301031612.jpg

    I then powered the minidock which and ran the script on the Omega via ssh terminal.

    Screenshot_20151122-165835-01.jpeg

    Screenshot_20151122-165830-01.jpeg

    Screenshot_20151122-165835-01.jpeg

    So for me. One of the Arduino Docks works but but it looks like the other one does accept the bootloader (might be fried.)

    0 Lazar Demin 1 Reply
  • Lazar Demin
    administrators

    @Russ-Terrell Yeah, that message will show up but the flash should still work. Try enabling Upload verbosity in the Arduino IDE settings and posting the message.

    0
  • Lazar Demin
    administrators

    @Tchernobil Are you using an Expansion Dock? Can you post some photos of the setup?

    0
  • Lazar Demin
    administrators

    @Maurice glad that it worked and sorry to hear that one of the Docks is non-responsive šŸ˜¢

    0
  • T

    I use the Espansion Dock. You can see a video of my setup here:
    http://www.grafigne.com/files/wires_arduinodock.mp4
    How can I test if my arduino dock is defective?

    0 Lazar Demin 1 Reply
  • Lazar Demin
    administrators

    @Tchernobil Can you try following the 'Using the Omega + Expansion Dock with the Arduino Dock ICSP Header' procedure from the Arduino Dock Initial Setup Guide?

    Let me know how it goes.

    0
  • T

    It's working!
    Thank you very much. Now I can use Arduino IDE to flash a sketch to the Arduino Dock.

    1 Lazar Demin 1 Reply
  • Lazar Demin
    administrators

    @Tchernobil awesome! glad to hear it worked
    @Maurice can you try following the same procedure on your non-cooperative Dock? (Might take a little more wire wrangling with the Mini Dock)

    0 M 1 Reply
  • R

    I still can't get the password to work. I reflashed the board using ICSP connector. Looks like it flashed ok.

    I was going to do the resync, but I'm not seeing blink2.ino.hex in the temp folder, only blink2.cpp.hex as listed in the Verbose list.

    X:\arduino-1.6.5\Arduino\hardware\tools\avr/bin/avr-objcopy -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0 D:\Users\Russ\AppData\Local\Temp\build8175480600231811290.tmp/blink2.cpp.elf D:\Users\Russ\AppData\Local\Temp\build8175480600231811290.tmp/blink2.cpp.eep
    X:\arduino-1.6.5\Arduino\hardware\tools\avr/bin/avr-objcopy -O ihex -R .eeprom D:\Users\Russ\AppData\Local\Temp\build8175480600231811290.tmp/blink2.cpp.elf D:\Users\Russ\AppData\Local\Temp\build8175480600231811290.tmp/blink2.cpp.hex

    Russ

    0 Lazar Demin 1 Reply
  • Lazar Demin
    administrators

    @Russ-Terrell Yeah, that should be good as well, the name might depend on the Arduino IDE version.

    Which password are you using in the Arduino IDE? It should be your Omega password which is onioneer by default

    0
arduino dock 42 guide 8
Log in to reply
 

Looks like your connection to Community was lost, please wait while we try to reconnect.