We have upgraded the community system as part of the upgrade a password reset is required for all users before login in.

New OS Release!



  • @Eric-Jaouen

    Hi Eric, I used the flash from USB method with firmware downloaded from the repository. The only challenges I ran into were that 1. I could never get the CP2102 driver to work on my mac so I had to switch to a Windows machine and 2. I actually had to read the instructions properly.



  • @György-Farkas I tried those methods and the boot always failed after the upgrade.

    Thanks for the note on how to enter blocks of code <head-slap> I write most of my notes in markdown I just didn't think to try it.

    For anyone interested here is the console out from the last attempt at upgrading:

    [    0.000000] Linux version 4.4.74 (root@3fbe4dcb626f) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3484-d8f14ba) ) #0 Tue Mar 27 17:21:32 2018
    [    0.000000] Board has DDR2
    [    0.000000] Analog PMU set to hw control
    [    0.000000] Digital PMU set to hw control
    [    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
    [    0.000000] bootconsole [early0] enabled
    [    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
    [    0.000000] MIPS: machine is Onion Omega2+
    [    0.000000] Determined physical RAM map:
    [    0.000000]  memory: 08000000 @ 00000000 (usable)
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
    [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
    [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.000000] Writing ErrCtl register=0000ac70
    [    0.000000] Readback ErrCtl register=0000ac70
    [    0.000000] Memory: 125488K/131072K available (3102K kernel code, 145K rwdata, 740K rodata, 164K init, 196K bss, 5584K reserved, 0K cma-reserved)
    [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    [    0.000000] NR_IRQS:256
    [    0.000000] intc: using register map from devicetree
    [    0.000000] CPU Clock: 580MHz
    [    0.000000] clocksource_probe: no matching clocksources found
    [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
    [    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
    [    0.007522] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
    [    0.070043] pid_max: default: 32768 minimum: 301
    [    0.074638] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.080974] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.094651] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.104159] futex hash table entries: 256 (order: -1, 3072 bytes)
    [    0.110171] pinctrl core: initialized pinctrl subsystem
    [    0.115934] NET: Registered protocol family 16
    [    0.140713] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.146270] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.151689] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.158289] i2c-mt7621 10000900.i2c: clock 100KHz, re-start not support
    [    0.165807] clocksource: Switched to clocksource MIPS
    [    0.172359] NET: Registered protocol family 2
    [    0.177573] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.184262] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.190447] TCP: Hash tables configured (established 1024 bind 1024)
    [    0.196638] UDP hash table entries: 256 (order: 0, 4096 bytes)
    [    0.202237] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    [    0.208621] NET: Registered protocol family 1
    [    0.219174] Crashlog allocated RAM at address 0x3f00000
    [    0.240601] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.246259] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    [    0.259019] io scheduler noop registered
    [    0.262762] io scheduler deadline registered (default)
    [    0.268867] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
    [    0.276283] console [ttyS0] disabled
    [    0.279716] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
    [    0.288482] console [ttyS0] enabled
    [    0.288482] console [ttyS0] enabled
    [    0.295462] bootconsole [early0] disabled
    [    0.295462] bootconsole [early0] disabled
    [    0.304138] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
    [    0.313648] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
    [    0.324213] spi-mt7621 10000b00.spi: sys_freq: 193333333
    [    0.334257] m25p80 spi32766.0: using chunked io (size=31)
    [    0.339823] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
    [    0.345331] 4 ofpart partitions found on MTD device spi32766.0
    [    0.351261] Creating 4 MTD partitions on "spi32766.0":
    [    0.356491] 0x000000000000-0x000000030000 : "u-boot"
    [    0.363299] 0x000000030000-0x000000040000 : "u-boot-env"
    [    0.370613] 0x000000040000-0x000000050000 : "factory"
    [    0.377665] 0x000000050000-0x000002000000 : "firmware"
    [    0.425571] 2 uimage-fw partitions found on MTD device firmware
    [    0.431622] 0x000000050000-0x000000197930 : "kernel"
    [    0.438345] 0x000000197930-0x000002000000 : "rootfs"
    [    0.445166] mtd: device 5 (rootfs) set to be root filesystem
    [    0.451049] 1 squashfs-split partitions found on MTD device rootfs
    [    0.457344] 0x000000740000-0x000002000000 : "rootfs_data"
    [    0.475238] rt3050-esw 10110000.esw: link changed 0x00
    [    0.481335] mtk_soc_eth 10100000.ethernet: generated random MAC address 9e:27:c0:7c:bd:c6
    [    0.490520] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
    [    0.499166] i2c /dev entries driver
    [    0.503268] mt7621_wdt 10000120.watchdog: Initialized
    [    0.510002] NET: Registered protocol family 10
    [    0.518796] NET: Registered protocol family 17
    [    0.523400] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
    [    0.536267] 8021q: 802.1Q VLAN Support v1.8
    [    0.547321] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
    [    0.555385] Freeing unused kernel memory: 164K (803e7000 - 80410000)
    [    1.581205] init: Console is alive
    [    1.584881] init: - watchdog -
    [    4.119739] kmodloader: loading kernel modules from /etc/modules-boot.d/*
    [    4.246212] usbcore: registered new interface driver usbfs
    [    4.251872] usbcore: registered new interface driver hub
    [    4.257423] usbcore: registered new device driver usb
    [    4.269152] exFAT: Version 1.2.9
    [    4.313410] SCSI subsystem initialized
    [    4.323951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    4.332405] ehci-platform: EHCI generic platform driver
    [    4.348100] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
    [    4.354904] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
    [    4.360250] ehci-platform 101c0000.ehci: EHCI Host Controller
    [    4.366131] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
    [    4.374287] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
    [    4.395851] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
    [    4.403370] hub 1-0:1.0: USB hub found
    [    4.407617] hub 1-0:1.0: 1 port detected
    [    4.416662] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    4.424607] ohci-platform: OHCI generic platform driver
    [    4.430271] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
    [    4.437246] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
    [    4.445359] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
    [    4.511010] hub 2-0:1.0: USB hub found
    [    4.515265] hub 2-0:1.0: 1 port detected
    [    4.532731] MTK MSDC device init.
    [    4.576003] mtk-sd: MediaTek MT6575 MSDC Driver
    [    4.584043] sdhci: Secure Digital Host Controller Interface driver
    [    4.590393] sdhci: Copyright(c) Pierre Ossman
    [    4.596345] sdhci-pltfm: SDHCI platform and OF driver helper
    [    4.606737] usbcore: registered new interface driver usb-storage
    [    4.616608] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
    [    4.634428] init: - preinit -
    [    4.861596] usb 1-1: new high-speed USB device number 2 using ehci-platform
    [    5.563707] usb-storage 1-1:1.0: USB Mass Storage device detected
    [    5.579807] rt3050-esw 10110000.esw: link changed 0x00
    [    5.585252] scsi host0: usb-storage 1-1:1.0
    [    5.667408] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
    Press the [f] key and hit [enter] to enter failsafe mode
    Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
    [    7.934427] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
    [    7.948624] urandom-seed: Seed file not found (/etc/urandom.seed)
    [    8.141385] procd: - early -
    [    8.144420] procd: - watchdog -
    [    8.724899] scsi 0:0:0:0: Direct-Access     Lexar    USB Flash Drive  1100 PQ: 0 ANSI: 4
    [    8.736656] sd 0:0:0:0: [sda] 30670848 512-byte logical blocks: (15.7 GB/14.6 GiB)
    [    8.745415] sd 0:0:0:0: [sda] Write Protect is off
    [    8.751432] sd 0:0:0:0: [sda] No Caching mode page found
    [    8.756878] sd 0:0:0:0: [sda] Assuming drive cache: write through
    [    8.769316]  sda: sda1
    [    8.776683] sd 0:0:0:0: [sda] Attached SCSI removable disk
    [    9.051295] rt3050-esw 10110000.esw: link changed 0x01
    [    9.274277] procd: - watchdog -
    [    9.277871] procd: - ubus -
    [    9.339012] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.348681] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.357972] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.371200] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.380477] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.389807] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.399175] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
    [    9.408733] procd: - init -
    Please press Enter to activate this console.
    [    9.825423] kmodloader: loading kernel modules from /etc/modules.d/*
    [    9.861537] ntfs: driver 2.1.32 [Flags: R/O MODULE].
    [    9.931616] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [    9.958000] gdma-rt2880 10002800.gdma: revision: 3, channels: 16
    [   10.409917]
    [   10.409917]
    [   10.409917] === pAd = c0572000, size = 1182848 ===
    [   10.409917]
    [   10.420797] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
    [   10.486876] Linux video capture interface: v2.00
    [   10.798967] hidraw: raw HID events driver (C) Jiri Kosina
    [   10.824321] ralink-i2s 10000a00.i2s: mclk 480KHz
    [   10.876477] max98090 0-0010: Unrecognized revision 0xff
    [   10.881794] max98090 0-0010: Mismatch in DT specified CODEC type.
    [   10.890583] max98090 0-0010: use default 2.8v micbias
    [   10.910742] asoc-simple-card sound: HiFi <-> 10000a00.i2s mapping ok
    [   10.953969] Bluetooth: Core ver 2.21
    [   10.957790] NET: Registered protocol family 31
    [   10.962300] Bluetooth: HCI device and connection manager initialized
    [   10.968788] Bluetooth: HCI socket layer initialized
    [   10.973740] Bluetooth: L2CAP socket layer initialized
    [   10.978907] Bluetooth: SCO socket layer initialized
    [   10.986398] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [   10.991797] Bluetooth: BNEP filters: protocol multicast
    [   10.997154] Bluetooth: BNEP socket layer initialized
    [   11.009027] usbcore: registered new interface driver btusb
    [   11.018777] usbcore: registered new interface driver cdc_acm
    [   11.024528] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    [   11.036602] Bluetooth: HCI UART driver ver 2.3
    [   11.041123] Bluetooth: HCI UART protocol H4 registered
    [   11.046380] Bluetooth: HCI UART protocol BCSP registered
    [   11.056057] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [   11.062088] Bluetooth: HIDP socket layer initialized
    [   11.070206] ip_tables: (C) 2000-2006 Netfilter Core Team
    [   11.091610] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
    [   11.122407] Bluetooth: RFCOMM TTY layer initialized
    [   11.127453] Bluetooth: RFCOMM socket layer initialized
    [   11.132723] Bluetooth: RFCOMM ver 1.11
    [   11.144426] spidev spi32766.1: buggy DT: spidev listed directly in DT
    [   11.151044] ------------[ cut here ]------------
    [   11.155745] WARNING: CPU: 0 PID: 500 at drivers/spi/spidev.c:720 init_module+0x933c/0x9dec [spidev]()
    [   11.165110] Modules linked in: spidev(+) snd_usbmidi_lib slhc rfcomm nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables hidp hid_generic hci_uart crc_ccitt cdc_acm btusb btintel bnep bluetooth snd_soc_simple_card snd_soc_ralink_i2s snd_soc_wm8960 snd_soc_max98090 videobuf2_vmalloc videobuf2_memops videobuf2_core hid v4l2_common videodev evdev snd_soc_core mt_wifi ralink_gdma virt_dma ledtrig_oneshot ledtrig_morse ledtrig_heartbeat ledtrig_gpio ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables msdos snd_pcm_dmaengine snd_compress snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd input_core soundcore vfat fat ntfs configfs autofs4 nls_utf8 nls_iso8859_1 nls_cp437 regmap_i2c dma_shared_buffer ecb cmac mmc_block usb_storage sdhci_pltfm sdhci mtk_sd mmc_core leds_gpio ohci_platform ohci_hcd ledtrig_transient ehci_platform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache exfat usbcore nls_base usb_common crc16 cryptomgr aead crypto_null crc32c_generic crypto_hash
    [   11.272042] CPU: 0 PID: 500 Comm: kmodloader Not tainted 4.4.74 #0
    [   11.278320] Stack : 80380780 00000000 00000001 803d0000 87d2078c 803cae63 80361c18 000001f4
              80413438 00000012 0000001a 024000c0 80066378 8004af58 80367120 803c0000
              00000003 00000012 80365524 87569b4c 80066378 80048ec4 00000000 00000000
              00000001 00000000 00000000 00000000 00000000 00000000 00000000 00000000
              00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
              ...
    [   11.314474] Call Trace:
    [   11.317029] [<80066378>] module_sect_show+0x0/0x18
    [   11.321895] [<8004af58>] vprintk_default+0x24/0x30
    [   11.326786] [<80066378>] module_sect_show+0x0/0x18
    [   11.331649] [<80048ec4>] printk+0x2c/0x38
    [   11.335728] [<8002552c>] warn_slowpath_common+0xa0/0xd0
    [   11.341059] [<8014de3c>] dump_stack+0x14/0x28
    [   11.345482] [<80014908>] show_stack+0x50/0x84
    [   11.349917] [<8002552c>] warn_slowpath_common+0xa0/0xd0
    [   11.355226] [<8775833c>] init_module+0x933c/0x9dec [spidev]
    [   11.360912] [<800255e4>] warn_slowpath_null+0x18/0x24
    [   11.366070] [<801fb304>] of_match_node+0x20/0x44
    [   11.370778] [<8775833c>] init_module+0x933c/0x9dec [spidev]
    [   11.376466] [<801c0a10>] devm_kfree+0x20/0x44
    [   11.380903] [<801e1bd8>] spi_drv_probe+0x3c/0x84
    [   11.385597] [<801bd540>] driver_probe_device+0x120/0x288
    [   11.391023] [<8008b928>] kstrdup+0x44/0x8c
    [   11.395193] [<801e1ad8>] spi_match_device+0x38/0xa8
    [   11.400181] [<801bd724>] __driver_attach+0x7c/0xb4
    [   11.405044] [<801bb948>] next_device+0x10/0x30
    [   11.409571] [<801bd6a8>] __driver_attach+0x0/0xb4
    [   11.414341] [<801bba04>] bus_for_each_dev+0x9c/0xac
    [   11.419311] [<80303c9c>] klist_add_tail+0x24/0x50
    [   11.424092] [<801bb7d8>] bus_get+0x2c/0x50
    [   11.428282] [<801bcc38>] bus_add_driver+0xec/0x20c
    [   11.433151] [<800ae92c>] exact_match+0x0/0x8
    [   11.437503] [<800aee34>] exact_lock+0x0/0x24
    [   11.441855] [<801bde3c>] driver_register+0xa8/0xf8
    [   11.446736] [<8774f000>] init_module+0x0/0xdc [spidev]
    [   11.451982] [<8774f098>] init_module+0x98/0xdc [spidev]
    [   11.457308] [<80159a08>] kasprintf+0x1c/0x28
    [   11.461656] [<800458b0>] __wake_up+0x24/0x48
    [   11.466007] [<8774f000>] init_module+0x0/0xdc [spidev]
    [   11.471243] [<8000d938>] do_one_initcall+0x1e8/0x214
    [   11.476305] [<800458b0>] __wake_up+0x24/0x48
    [   11.480641] [<8774f000>] init_module+0x0/0xdc [spidev]
    [   11.485887] [<80034568>] call_usermodehelper_exec+0x144/0x160
    [   11.491731] [<80034058>] call_usermodehelper_setup+0x38/0xa8
    [   11.497512] [<80066378>] module_sect_show+0x0/0x18
    [   11.502394] [<80067598>] do_init_module+0x74/0x1cc
    [   11.507286] [<8009f418>] __vunmap+0xf0/0x114
    [   11.511650] [<80068e2c>] load_module+0x16c0/0x1b68
    [   11.516531] [<80066964>] unknown_module_param_cb+0x0/0xac
    [   11.522015] [<8009f90c>] __vmalloc_node+0x34/0x40
    [   11.526826] [<80069368>] SyS_init_module+0x94/0x180
    [   11.531780] [<80069404>] SyS_init_module+0x130/0x180
    [   11.536861] [<8000682c>] syscall_common+0x30/0x54
    [   11.541642] [<80008c58>] __bzero+0xbc/0x164
    [   11.545897]
    [   11.547411] ---[ end trace 0dc5952289822307 ]---
    [   11.559464] usbcore: registered new interface driver ums-alauda
    [   11.568641] usbcore: registered new interface driver ums-cypress
    [   11.577854] usbcore: registered new interface driver ums-datafab
    [   11.586823] usbcore: registered new interface driver ums-freecom
    [   11.595992] usbcore: registered new interface driver ums-isd200
    [   11.605150] usbcore: registered new interface driver ums-jumpshot
    [   11.614272] usbcore: registered new interface driver ums-karma
    [   11.623985] usbcore: registered new interface driver ums-sddr09
    [   11.633134] usbcore: registered new interface driver ums-sddr55
    [   11.642585] usbcore: registered new interface driver ums-usbat
    [   11.654803] usbcore: registered new interface driver usbhid
    [   11.660534] usbhid: USB HID core driver
    [   11.668283] usbcore: registered new interface driver usblp
    [   11.682281] usbcore: registered new interface driver usbserial
    [   11.688400] usbcore: registered new interface driver usbserial_generic
    [   11.695130] usbserial: USB Serial support registered for generic
    [   11.713795] Driver for 1-wire Dallas network protocol.
    [   11.740496] xt_time: kernel timezone is -0000
    [   11.747368] usbcore: registered new interface driver ch341
    [   11.753061] usbserial: USB Serial support registered for ch341-uart
    [   11.761946] usbcore: registered new interface driver cp210x
    [   11.767814] usbserial: USB Serial support registered for cp210x
    [   11.777485] usbcore: registered new interface driver ftdi_sio
    [   11.783435] usbserial: USB Serial support registered for FTDI USB Serial Device
    [   11.805786] usbcore: registered new interface driver pl2303
    [   11.811641] usbserial: USB Serial support registered for pl2303
    [   11.823166] PPP generic driver version 2.4.2
    [   11.830833] NET: Registered protocol family 24
    [   11.848907] usbcore: registered new interface driver snd-usb-audio
    [   11.871030] usbcore: registered new interface driver uvcvideo
    [   11.876929] USB Video Class driver (1.1.1)
    [   11.889816] usbcore: registered new interface driver option
    [   11.895584] usbserial: USB Serial support registered for GSM modem (1-port)
    [   11.908355] kmodloader: done loading kernel modules from /etc/modules.d/*
    [   12.180432] random: jshn: uninitialized urandom read (4 bytes read, 32 bits of entropy available)
    [   12.338508] random: jshn: uninitialized urandom read (4 bytes read, 32 bits of entropy available)
    [   23.367307] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready
    [   24.073157]
    [   24.073157] _      _____   ___  ___    _________  ___  ____
    [   24.073157] | | /| / / _ | / _ \/ _ \  / ___/ __ \/ _ \/ __/ V1.0
    [   24.073157] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/
    [   24.073157] |__/|__/_/ |_/_/|_/_/     \___/\____/_/|_/___/
    [   24.073157]             Onion Enhanced MT7688 WiFi Driver
    [   24.073157]
    [   24.435870] DMA Scheduler Mode=0(LMAC)
    [   24.439704] efuse_probe: efuse = 10000012
    [   24.443826] 1. Phy Mode = 14
    [   24.611598] ERROR: initialization error 781:
    [   24.611598] buffer=303030303030303030306138
    [   24.611598]
    [   24.729924] ERROR: initialization error 781:
    [   24.729924] buffer=303030303030303030306138
    [   24.729924]
    [   25.289526] ERROR: initialization error 781:
    [   25.289526] buffer=303030303030303030306138
    [   25.289526]
    [   53.739438]
    [   53.739438] _      _____   ___  ___    _________  ___  ____
    [   53.739438] | | /| / / _ | / _ \/ _ \  / ___/ __ \/ _ \/ __/ V1.0
    [   53.739438] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/
    [   53.739438] |__/|__/_/ |_/_/|_/_/     \___/\____/_/|_/___/
    [   53.739438]             Onion Enhanced MT7688 WiFi Driver
    [   53.739438]
    [   53.896622] Kernel bug detected[#1]:
    [   53.900278] CPU: 0 PID: 1414 Comm: ifconfig Tainted: G        W       4.4.74 #0
    [   53.907693] task: 87dce338 ti: 86a52000 task.ti: 86a52000
    [   53.913162] $ 0   : 00000000 80410000 00000001 ffff9fdc
    [   53.918480] $ 4   : c062302c ffff9fe6 86e765f0 c062302c
    [   53.923790] $ 8   : 0000001c c0609238 86e41f2c 00000000
    [   53.929101] $12   : 00000000 b7924e27 00000000 00000000
    [   53.934410] $16   : c062302c 00090000 000b0000 86f40000
    [   53.939721] $20   : c062302c c0602000 00000001 7fcf296c
    [   53.945032] $24   : 00000018 80043388
    [   53.950342] $28   : 86a52000 86a53c78 00000000 86e52630
    [   53.955654] Hi    : 00000000
    [   53.958570] Lo    : 0000000a
    [   53.961506] epc   : 80053f18 add_timer+0x8/0x14
    [   53.966615] ra    : 86e52630 RTMPSetTimer+0x80/0x110 [mt_wifi]
    [   53.972527] Status: 1100e503 KERNEL EXL IE
    [   53.976783] Cause : 10800034 (ExcCode 0d)
    [   53.980847] PrId  : 00019655 (MIPS 24KEc)
    [   53.984908] Modules linked in: pppoe ppp_async option iptable_nat w1_therm w1_gpio uvcvideo usb_wwan snd_usb_audio pppox ppp_generic pl2303 nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT ipt_MASQUERADE ftdi_sio cp210x ch341 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG wire videobuf2_v4l2 usbserial usblp usbhid ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda uinput spidev snd_usbmidi_lib slhc rfcomm nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables hidp hid_generic hci_uart crc_ccitt cdc_acm btusb btintel bnep bluetooth snd_soc_simple_card snd_soc_ralink_i2s snd_soc_wm8960 snd_soc_max98090 videobuf2_vmalloc videobuf2_memops videobuf2_core hid v4l2_common videodev evdev snd_soc_core mt_wifi ralink_gdma virt_dma ledtrig_oneshot ledtrig_morse ledtrig_heartbeat ledtrig_gpio ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables msdos snd_pcm_dmaengine snd_compress snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd input_core soundcore vfat fat ntfs configfs autofs4 nls_utf8 nls_iso8859_1 nls_cp437 regmap_i2c dma_shared_buffer ecb cmac mmc_block usb_storage sdhci_pltfm sdhci mtk_sd mmc_core leds_gpio ohci_platform ohci_hcd ledtrig_transient ehci_platform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache exfat usbcore nls_base usb_common crc16 cryptomgr aead crypto_null crc32c_generic crypto_hash
    [   54.135010] Process ifconfig (pid: 1414, threadinfo=86a52000, task=87dce338, tls=77753d48)
    [   54.143383] Stack : c0572000 00090000 000b0000 c0572000 c0572000 86e40a74 c0576960 c0692000
              86f16314 86eaafb0 00000001 86e50bf8 c0572000 86f40000 c0692000 86f16314
              86f16314 87642f00 7fcf29ec 86e53948 7fcf29ec 86efe2f0 86f16314 00000000
              00000141 0000581c 86c5c000 c0572000 86c5c000 0000502e 803d0000 ffff9fcc
              87642f00 86ed8fd0 803caa00 8780fc90 86a53d08 86a53d08 00000000 00000000
              ...
    [   54.179516] Call Trace:
    [   54.182006] [<80053f18>] add_timer+0x8/0x14
    [   54.186715] [<86e52630>] RTMPSetTimer+0x80/0x110 [mt_wifi]
    [   54.193198] [<86e40a74>] MlmeInit+0x1ac/0x2f4 [mt_wifi]
    [   54.199420] [<86e53948>] rt28xx_init+0x114/0x720 [mt_wifi]
    [   54.205910] [<86ed8fd0>] rt28xx_open+0xbc/0x320 [mt_wifi]
    [   54.212315] [<86e6a068>] RTMP_COM_IoctlHandle+0x508/0x9a4 [mt_wifi]
    [   54.219600] [<86ed87f4>] MainVirtualIF_open+0x74/0x110 [mt_wifi]
    [   54.226167] [<8021f104>] __dev_open+0xe0/0x148
    [   54.230681] [<8021f408>] __dev_change_flags+0xb8/0x174
    [   54.235897] [<8021f4ec>] dev_change_flags+0x28/0x70
    [   54.240849] [<80282f78>] devinet_ioctl+0x224/0x6dc
    [   54.245723] [<80204300>] sock_ioctl+0x298/0x2f8
    [   54.250330] [<800bbbac>] do_vfs_ioctl+0x4fc/0x5b4
    [   54.255103] [<800bbcb4>] SyS_ioctl+0x50/0x98
    [   54.259445] [<8000682c>] syscall_common+0x30/0x54
    [   54.264210]
    [   54.265716]
    Code: 27bd0030  8c820004  0002102b <00020336> 08014f5f  8c850008  27bdffd0  afbf002c  afb30028
    [   54.275874] ---[ end trace 0dc5952289822308 ]---
    [   54.284381] Kernel panic - not syncing: Fatal exception in interrupt
    [   54.292922] Rebooting in 3 seconds..
    


  • @György-Farkas said in New OS Release!:

    Today - after a FACTORY RESET - I upgraded it successfully from b176 to b178 on Serial Console with

    I am now able to do straight Serial Console upgrade from b159 to latest b178 without Factory Reset.
    WiFi connection appears to be working OK for now and open connection is very fast.
    Still doing more testing.



  • @Mark-Fisher Please do give it a chance! 😉 You should try to boot your bare Omega2+ without that USB stick and without the Ethernet Expansion.

    Here is my b178 bootlog - a bare Omega2+ on a Breadboard Dock:

    [    0.000000] Linux version 4.4.74 (root@3fbe4dcb626f) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3484-d8f14ba) ) #0 Tue Mar 27 17:21:32 2018
    [    0.000000] Board has DDR2
    [    0.000000] Analog PMU set to hw control
    [    0.000000] Digital PMU set to hw control
    [    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
    [    0.000000] bootconsole [early0] enabled
    [    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
    [    0.000000] MIPS: machine is Onion Omega2+
    [    0.000000] Determined physical RAM map:
    [    0.000000]  memory: 08000000 @ 00000000 (usable)
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
    [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
    [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.000000] Writing ErrCtl register=0000e8d0
    [    0.000000] Readback ErrCtl register=0000e8d0
    [    0.000000] Memory: 125488K/131072K available (3102K kernel code, 145K rwdata, 740K rodata, 164K init, 196K bss, 5584K reserved, 0K cma-reserved)
    [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    [    0.000000] NR_IRQS:256
    [    0.000000] intc: using register map from devicetree
    [    0.000000] CPU Clock: 580MHz
    [    0.000000] clocksource_probe: no matching clocksources found
    [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
    [    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
    [    0.007522] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
    [    0.070042] pid_max: default: 32768 minimum: 301
    [    0.074637] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.080974] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.094650] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.104159] futex hash table entries: 256 (order: -1, 3072 bytes)
    [    0.110171] pinctrl core: initialized pinctrl subsystem
    [    0.115934] NET: Registered protocol family 16
    [    0.140714] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.146271] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.151690] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.158289] i2c-mt7621 10000900.i2c: clock 100KHz, re-start not support
    [    0.165807] clocksource: Switched to clocksource MIPS
    [    0.172359] NET: Registered protocol family 2
    [    0.177573] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.184262] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.190447] TCP: Hash tables configured (established 1024 bind 1024)
    [    0.196639] UDP hash table entries: 256 (order: 0, 4096 bytes)
    [    0.202238] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    [    0.208622] NET: Registered protocol family 1
    [    0.219174] Crashlog allocated RAM at address 0x3f00000
    [    0.240599] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.246257] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    [    0.259017] io scheduler noop registered
    [    0.262760] io scheduler deadline registered (default)
    [    0.268865] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
    [    0.276281] console [ttyS0] disabled
    [    0.279714] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
    [    0.288480] console [ttyS0] enabled
    [    0.288480] console [ttyS0] enabled
    [    0.295460] bootconsole [early0] disabled
    [    0.295460] bootconsole [early0] disabled
    [    0.304135] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
    [    0.313646] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
    [    0.324210] spi-mt7621 10000b00.spi: sys_freq: 193333333
    [    0.334254] m25p80 spi32766.0: using chunked io (size=31)
    [    0.339820] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
    [    0.345329] 4 ofpart partitions found on MTD device spi32766.0
    [    0.351259] Creating 4 MTD partitions on "spi32766.0":
    [    0.356488] 0x000000000000-0x000000030000 : "u-boot"
    [    0.363297] 0x000000030000-0x000000040000 : "u-boot-env"
    [    0.370611] 0x000000040000-0x000000050000 : "factory"
    [    0.377661] 0x000000050000-0x000002000000 : "firmware"
    [    0.425569] 2 uimage-fw partitions found on MTD device firmware
    [    0.431622] 0x000000050000-0x000000197930 : "kernel"
    [    0.438345] 0x000000197930-0x000002000000 : "rootfs"
    [    0.445165] mtd: device 5 (rootfs) set to be root filesystem
    [    0.451049] 1 squashfs-split partitions found on MTD device rootfs
    [    0.457343] 0x000000740000-0x000002000000 : "rootfs_data"
    [    0.475237] rt3050-esw 10110000.esw: link changed 0x00
    [    0.482131] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
    [    0.490781] i2c /dev entries driver
    [    0.494891] mt7621_wdt 10000120.watchdog: Initialized
    [    0.501613] NET: Registered protocol family 10
    [    0.510383] NET: Registered protocol family 17
    [    0.514987] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
    [    0.527855] 8021q: 802.1Q VLAN Support v1.8
    [    0.538880] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
    [    0.547014] Freeing unused kernel memory: 164K (803e7000 - 80410000)
    [    1.572459] init: Console is alive
    [    1.576232] init: - watchdog -
    [    4.113400] kmodloader: loading kernel modules from /etc/modules-boot.d/*
    [    4.238867] usbcore: registered new interface driver usbfs
    [    4.244528] usbcore: registered new interface driver hub
    [    4.250112] usbcore: registered new device driver usb
    [    4.261603] exFAT: Version 1.2.9
    [    4.303775] SCSI subsystem initialized
    [    4.314279] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    4.322715] ehci-platform: EHCI generic platform driver
    [    4.338414] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
    [    4.345217] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
    [    4.350563] ehci-platform 101c0000.ehci: EHCI Host Controller
    [    4.356444] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
    [    4.364597] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
    [    4.385853] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
    [    4.393369] hub 1-0:1.0: USB hub found
    [    4.397614] hub 1-0:1.0: 1 port detected
    [    4.406640] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    4.414585] ohci-platform: OHCI generic platform driver
    [    4.420244] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
    [    4.427216] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
    [    4.435328] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
    [    4.501005] hub 2-0:1.0: USB hub found
    [    4.505261] hub 2-0:1.0: 1 port detected
    [    4.522697] MTK MSDC device init.
    [    4.566006] mtk-sd: MediaTek MT6575 MSDC Driver
    [    4.574007] sdhci: Secure Digital Host Controller Interface driver
    [    4.580355] sdhci: Copyright(c) Pierre Ossman
    [    4.586299] sdhci-pltfm: SDHCI platform and OF driver helper
    [    4.596672] usbcore: registered new interface driver usb-storage
    [    4.606363] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
    [    4.624173] init: - preinit -
    [    5.474753] rt3050-esw 10110000.esw: link changed 0x00
    Press the [f] key and hit [enter] to enter failsafe mode
    Press the [1], [2], [3] or [4] key and hit [enter] to select the debug[    5.673349] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
     level
    [    8.936588] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
    [    8.944037] jffs2_build_filesystem(): unlocking the mtd device... done.
    [    8.950774] jffs2_build_filesystem(): erasing all blocks after the end marker... 
    [   81.295843] random: nonblocking pool is initialized
    [  135.190332] done.
    [  135.192341] jffs2: notice: (399) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [  135.209624] mount_root: overlay filesystem has not been fully initialized yet
    [  135.221573] mount_root: switching to jffs2 overlay
    - config restore -
    [  135.531945] urandom-seed: Seed file not found (/etc/urandom.seed)
    [  135.653394] procd: - early -
    [  135.657181] procd: - watchdog -
    [  136.379387] procd: - watchdog -
    [  136.382861] procd: - ubus -
    [  136.437866] procd: - init -
    Please press Enter to activate this console.
    [  136.865769] kmodloader: loading kernel modules from /etc/modules.d/*
    [  136.905185] ntfs: driver 2.1.32 [Flags: R/O MODULE].
    [  136.974676] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [  137.000984] gdma-rt2880 10002800.gdma: revision: 3, channels: 16
    [  137.452644] 
    [  137.452644] 
    [  137.452644] === pAd = c0611000, size = 1182848 ===
    [  137.452644] 
    [  137.463553] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
    [  137.536032] Linux video capture interface: v2.00
    [  137.579710] hidraw: raw HID events driver (C) Jiri Kosina
    [  137.604786] ralink-i2s 10000a00.i2s: mclk 480KHz
    [  137.636479] max98090 0-0010: Unrecognized revision 0xff
    [  137.641797] max98090 0-0010: Mismatch in DT specified CODEC type.
    [  137.650574] max98090 0-0010: use default 2.8v micbias
    [  137.670026] asoc-simple-card sound: HiFi <-> 10000a00.i2s mapping ok
    [  137.713565] Bluetooth: Core ver 2.21
    [  137.717386] NET: Registered protocol family 31
    [  137.721895] Bluetooth: HCI device and connection manager initialized
    [  137.728376] Bluetooth: HCI socket layer initialized
    [  137.733329] Bluetooth: L2CAP socket layer initialized
    [  137.738526] Bluetooth: SCO socket layer initialized
    [  137.746021] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [  137.751422] Bluetooth: BNEP filters: protocol multicast
    [  137.756767] Bluetooth: BNEP socket layer initialized
    [  137.768614] usbcore: registered new interface driver btusb
    [  137.778275] usbcore: registered new interface driver cdc_acm
    [  137.784027] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    [  137.796072] Bluetooth: HCI UART driver ver 2.3
    [  137.800594] Bluetooth: HCI UART protocol H4 registered
    [  137.805843] Bluetooth: HCI UART protocol BCSP registered
    [  137.815385] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [  137.821487] Bluetooth: HIDP socket layer initialized
    [  137.829583] ip_tables: (C) 2000-2006 Netfilter Core Team
    [  137.850884] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
    [  137.881386] Bluetooth: RFCOMM TTY layer initialized
    [  137.886434] Bluetooth: RFCOMM socket layer initialized
    [  137.891671] Bluetooth: RFCOMM ver 1.11
    [  137.903440] spidev spi32766.1: buggy DT: spidev listed directly in DT
    [  137.910060] ------------[ cut here ]------------
    [  137.914763] WARNING: CPU: 0 PID: 482 at drivers/spi/spidev.c:720 init_module+0x4d33c/0x4ddec [spidev]()
    [  137.924302] Modules linked in: spidev(+) snd_usbmidi_lib slhc rfcomm nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables hidp hid_generic hci_uart crc_ccitt cdc_acm btusb btintel bnep bluetooth snd_soc_simple_card snd_soc_ralink_i2s snd_soc_wm8960 snd_soc_max98090 videobuf2_vmalloc videobuf2_memops videobuf2_core hid v4l2_common videodev evdev snd_soc_core mt_wifi ralink_gdma virt_dma ledtrig_oneshot ledtrig_morse ledtrig_heartbeat ledtrig_gpio ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables msdos snd_pcm_dmaengine snd_compress snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd input_core soundcore vfat fat ntfs configfs autofs4 nls_utf8 nls_iso8859_1 nls_cp437 regmap_i2c dma_shared_buffer ecb cmac mmc_block usb_storage sdhci_pltfm sdhci mtk_sd mmc_core leds_gpio ohci_platform ohci_hcd ledtrig_transient ehci_platform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache exfat usbcore nls_base usb_common crc16 cryptomgr aead crypto_null crc32c_generic crypto_hash
    [  138.031238] CPU: 0 PID: 482 Comm: kmodloader Not tainted 4.4.74 #0
    [  138.037517] Stack : 80380780 00000000 00000001 803d0000 87d225bc 803cae63 80361c18 000001e2
    	  80413438 0000000f 0000001a 024000c0 80066378 8004af58 80367120 803c0000
    	  00000003 0000000f 80365524 8752fb4c 80066378 80048ec4 00000000 00000000
    	  00000001 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    	  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    	  ...
    [  138.073675] Call Trace:
    [  138.076228] [<80066378>] module_sect_show+0x0/0x18
    [  138.081097] [<8004af58>] vprintk_default+0x24/0x30
    [  138.085989] [<80066378>] module_sect_show+0x0/0x18
    [  138.090851] [<80048ec4>] printk+0x2c/0x38
    [  138.094931] [<8002552c>] warn_slowpath_common+0xa0/0xd0
    [  138.100263] [<8014de3c>] dump_stack+0x14/0x28
    [  138.104685] [<80014908>] show_stack+0x50/0x84
    [  138.109121] [<8002552c>] warn_slowpath_common+0xa0/0xd0
    [  138.114431] [<86c6233c>] init_module+0x4d33c/0x4ddec [spidev]
    [  138.120292] [<800255e4>] warn_slowpath_null+0x18/0x24
    [  138.125436] [<801fb304>] of_match_node+0x20/0x44
    [  138.130162] [<86c6233c>] init_module+0x4d33c/0x4ddec [spidev]
    [  138.136028] [<801c0a10>] devm_kfree+0x20/0x44
    [  138.140468] [<801e1bd8>] spi_drv_probe+0x3c/0x84
    [  138.145165] [<801bd540>] driver_probe_device+0x120/0x288
    [  138.150594] [<8008b928>] kstrdup+0x44/0x8c
    [  138.154766] [<801e1ad8>] spi_match_device+0x38/0xa8
    [  138.159759] [<801bd724>] __driver_attach+0x7c/0xb4
    [  138.164622] [<801bb948>] next_device+0x10/0x30
    [  138.169152] [<801bd6a8>] __driver_attach+0x0/0xb4
    [  138.173924] [<801bba04>] bus_for_each_dev+0x9c/0xac
    [  138.178895] [<80303c9c>] klist_add_tail+0x24/0x50
    [  138.183677] [<801bb7d8>] bus_get+0x2c/0x50
    [  138.187870] [<801bcc38>] bus_add_driver+0xec/0x20c
    [  138.192741] [<800ae92c>] exact_match+0x0/0x8
    [  138.197092] [<800aee34>] exact_lock+0x0/0x24
    [  138.201447] [<801bde3c>] driver_register+0xa8/0xf8
    [  138.206330] [<86c15000>] init_module+0x0/0xdc [spidev]
    [  138.211582] [<86c15098>] init_module+0x98/0xdc [spidev]
    [  138.216909] [<80159a08>] kasprintf+0x1c/0x28
    [  138.221258] [<800458b0>] __wake_up+0x24/0x48
    [  138.225592] [<86c15000>] init_module+0x0/0xdc [spidev]
    [  138.230843] [<8000d938>] do_one_initcall+0x1e8/0x214
    [  138.235909] [<800458b0>] __wake_up+0x24/0x48
    [  138.240246] [<86c15000>] init_module+0x0/0xdc [spidev]
    [  138.245476] [<80034568>] call_usermodehelper_exec+0x144/0x160
    [  138.251341] [<80034058>] call_usermodehelper_setup+0x38/0xa8
    [  138.257121] [<80066378>] module_sect_show+0x0/0x18
    [  138.262003] [<80067598>] do_init_module+0x74/0x1cc
    [  138.266897] [<8009f418>] __vunmap+0xf0/0x114
    [  138.271267] [<80068e2c>] load_module+0x16c0/0x1b68
    [  138.276152] [<80066964>] unknown_module_param_cb+0x0/0xac
    [  138.281638] [<8009f90c>] __vmalloc_node+0x34/0x40
    [  138.286451] [<80069368>] SyS_init_module+0x94/0x180
    [  138.291404] [<80069404>] SyS_init_module+0x130/0x180
    [  138.296486] [<8000682c>] syscall_common+0x30/0x54
    [  138.301271] [<800aa748>] SyS_open+0x0/0x14
    [  138.305424] 
    [  138.306950] ---[ end trace 0ffd864dc48f22ff ]---
    [  138.318993] usbcore: registered new interface driver ums-alauda
    [  138.328179] usbcore: registered new interface driver ums-cypress
    [  138.337400] usbcore: registered new interface driver ums-datafab
    [  138.346388] usbcore: registered new interface driver ums-freecom
    [  138.355487] usbcore: registered new interface driver ums-isd200
    [  138.364671] usbcore: registered new interface driver ums-jumpshot
    [  138.373760] usbcore: registered new interface driver ums-karma
    [  138.383484] usbcore: registered new interface driver ums-sddr09
    [  138.392591] usbcore: registered new interface driver ums-sddr55
    [  138.402036] usbcore: registered new interface driver ums-usbat
    [  138.414267] usbcore: registered new interface driver usbhid
    [  138.419999] usbhid: USB HID core driver
    [  138.427727] usbcore: registered new interface driver usblp
    [  138.441806] usbcore: registered new interface driver usbserial
    [  138.447911] usbcore: registered new interface driver usbserial_generic
    [  138.454645] usbserial: USB Serial support registered for generic
    [  138.473319] Driver for 1-wire Dallas network protocol.
    [  138.499875] xt_time: kernel timezone is -0000
    [  138.506718] usbcore: registered new interface driver ch341
    [  138.512402] usbserial: USB Serial support registered for ch341-uart
    [  138.521222] usbcore: registered new interface driver cp210x
    [  138.527078] usbserial: USB Serial support registered for cp210x
    [  138.536646] usbcore: registered new interface driver ftdi_sio
    [  138.542606] usbserial: USB Serial support registered for FTDI USB Serial Device
    [  138.564810] usbcore: registered new interface driver pl2303
    [  138.570672] usbserial: USB Serial support registered for pl2303
    [  138.582198] PPP generic driver version 2.4.2
    [  138.589834] NET: Registered protocol family 24
    [  138.608009] usbcore: registered new interface driver snd-usb-audio
    [  138.630185] usbcore: registered new interface driver uvcvideo
    [  138.636083] USB Video Class driver (1.1.1)
    [  138.648786] usbcore: registered new interface driver option
    [  138.654554] usbserial: USB Serial support registered for GSM modem (1-port)
    [  138.667190] kmodloader: done loading kernel modules from /etc/modules.d/*
    [  148.697338] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready
    [  149.349507] 
    [  149.349507] _      _____   ___  ___    _________  ___  ____
    [  149.349507] | | /| / / _ | / _ \/ _ \  / ___/ __ \/ _ \/ __/ V1.0
    [  149.349507] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/  
    [  149.349507] |__/|__/_/ |_/_/|_/_/     \___/\____/_/|_/___/  
    [  149.349507] 		   Onion Enhanced MT7688 WiFi Driver 
    [  149.349507] 
    [  149.595911] DMA Scheduler Mode=0(LMAC)
    [  149.599745] efuse_probe: efuse = 10000012
    [  149.603870] 1. Phy Mode = 14
    [  149.780497] 2. Phy Mode = 14
    [  149.783481] 3. Phy Mode = 14
    [  149.791654] 	WTBL Segment 1 info:
    [  149.795033] 		MemBaseAddr/FID:0x28000/0
    [  149.798980] 		EntrySize/Cnt:32/128
    [  149.802428] 	WTBL Segment 2 info:
    [  149.805785] 		MemBaseAddr/FID:0x40000/0
    [  149.809687] 		EntrySize/Cnt:64/128
    [  149.813132] 	WTBL Segment 3 info:
    [  149.816503] 		MemBaseAddr/FID:0x42000/64
    [  149.820479] 		EntrySize/Cnt:64/128
    [  149.823923] 	WTBL Segment 4 info:
    [  149.827295] 		MemBaseAddr/FID:0x44000/128
    [  149.831358] 		EntrySize/Cnt:32/128
    [  159.260633] device ra0 entered promiscuous mode
    [  159.265385] br-wlan: port 1(ra0) entered forwarding state
    [  159.270978] br-wlan: port 1(ra0) entered forwarding state
    [  159.277323] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready
    [  161.265819] br-wlan: port 1(ra0) entered forwarding state
    [  163.905049] device ra0 left promiscuous mode
    [  163.909582] br-wlan: port 1(ra0) entered disabled state
    [  164.979870] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready
    [  165.339502] 
    [  165.339502] _      _____   ___  ___    _________  ___  ____
    [  165.339502] | | /| / / _ | / _ \/ _ \  / ___/ __ \/ _ \/ __/ V1.0
    [  165.339502] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/  
    [  165.339502] |__/|__/_/ |_/_/|_/_/     \___/\____/_/|_/___/  
    [  165.339502] 		   Onion Enhanced MT7688 WiFi Driver 
    [  165.339502] 
    [  165.493575] DMA Scheduler Mode=0(LMAC)
    [  165.497462] efuse_probe: efuse = 10000012
    [  165.501582] 1. Phy Mode = 14
    [  165.678074] 2. Phy Mode = 14
    [  165.681053] 3. Phy Mode = 14
    [  165.684289] 	WTBL Segment 1 info:
    [  165.687701] 		MemBaseAddr/FID:0x28000/0
    [  165.691592] 		EntrySize/Cnt:32/128
    [  165.695036] 	WTBL Segment 2 info:
    [  165.698409] 		MemBaseAddr/FID:0x40000/0
    [  165.702297] 		EntrySize/Cnt:64/128
    [  165.705740] 	WTBL Segment 3 info:
    [  165.709114] 		MemBaseAddr/FID:0x42000/64
    [  165.713090] 		EntrySize/Cnt:64/128
    [  165.716581] 	WTBL Segment 4 info:
    [  165.719945] 		MemBaseAddr/FID:0x44000/128
    [  165.724014] 		EntrySize/Cnt:32/128
    [  174.160028] device ra0 entered promiscuous mode
    [  174.164782] br-wlan: port 1(ra0) entered forwarding state
    [  174.170370] br-wlan: port 1(ra0) entered forwarding state
    [  174.177234] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready
    [  176.165838] br-wlan: port 1(ra0) entered forwarding state
    [  203.050942] Interface apcli0 link up! (WPA2PSK AES)
    
    
    
    BusyBox v1.25.1 () built-in shell (ash)
    
       ____       _             ____
      / __ \___  (_)__  ___    / __ \__ _  ___ ___ ____ _
     / /_/ / _ \/ / _ \/ _ \  / /_/ /  ' \/ -_) _ `/ _ `/
     \____/_//_/_/\___/_//_/  \____/_/_/_/\__/\_, /\_,_/
     W H A T  W I L L  Y O U  I N V E N T ? /___/
     -----------------------------------------------------
       Ω-ware: 0.2.0 b178
     -----------------------------------------------------
    

    Good luck!



  • @Mark-Fisher I only use the Ethernet connection of Omega2(+) occasionally. I doesn't have genuine Onion Ethernet Expansion - I use a compatible magnetics.
    I upgraded an O2+ via Ethernet connection from b160 to b178 successfully on Serial Console with oupgrade --latest.

    [    0.000000] Linux version 4.4.74 (root@3fbe4dcb626f) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3484-d8f14ba) ) #0 Tue Mar 27 17:21:32 2018
    [    0.000000] Board has DDR2
    [    0.000000] Analog PMU set to hw control
    [    0.000000] Digital PMU set to hw control
    [    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
    [    0.000000] bootconsole [early0] enabled
    [    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
    [    0.000000] MIPS: machine is Onion Omega2+
    [    0.000000] Determined physical RAM map:
    [    0.000000]  memory: 08000000 @ 00000000 (usable)
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
    [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
    [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.000000] Writing ErrCtl register=000710b0
    [    0.000000] Readback ErrCtl register=000710b0
    [    0.000000] Memory: 125488K/131072K available (3102K kernel code, 145K rwdata, 740K rodata, 164K init, 196K bss, 5584K reserved, 0K cma-reserved)
    [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    [    0.000000] NR_IRQS:256
    [    0.000000] intc: using register map from devicetree
    [    0.000000] CPU Clock: 580MHz
    [    0.000000] clocksource_probe: no matching clocksources found
    [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
    [    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
    [    0.007522] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
    [    0.070042] pid_max: default: 32768 minimum: 301
    [    0.074637] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.080973] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.094650] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.104159] futex hash table entries: 256 (order: -1, 3072 bytes)
    [    0.110171] pinctrl core: initialized pinctrl subsystem
    [    0.115934] NET: Registered protocol family 16
    [    0.140712] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.146269] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.151688] mt7621_gpio 10000600.gpio: registering 32 gpios
    [    0.158287] i2c-mt7621 10000900.i2c: clock 100KHz, re-start not support
    [    0.165806] clocksource: Switched to clocksource MIPS
    [    0.172358] NET: Registered protocol family 2
    [    0.177571] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.184260] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.190445] TCP: Hash tables configured (established 1024 bind 1024)
    [    0.196636] UDP hash table entries: 256 (order: 0, 4096 bytes)
    [    0.202236] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    [    0.208620] NET: Registered protocol family 1
    [    0.219172] Crashlog allocated RAM at address 0x3f00000
    [    0.240599] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.246257] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    [    0.259019] io scheduler noop registered
    [    0.262761] io scheduler deadline registered (default)
    [    0.268866] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
    [    0.276282] console [ttyS0] disabled
    [    0.279715] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
    [    0.288481] console [ttyS0] enabled
    [    0.288481] console [ttyS0] enabled
    [    0.295461] bootconsole [early0] disabled
    [    0.295461] bootconsole [early0] disabled
    [    0.304137] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
    [    0.313648] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
    [    0.324212] spi-mt7621 10000b00.spi: sys_freq: 193333333
    [    0.334256] m25p80 spi32766.0: using chunked io (size=31)
    [    0.339822] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
    [    0.345330] 4 ofpart partitions found on MTD device spi32766.0
    [    0.351260] Creating 4 MTD partitions on "spi32766.0":
    [    0.356490] 0x000000000000-0x000000030000 : "u-boot"
    [    0.363298] 0x000000030000-0x000000040000 : "u-boot-env"
    [    0.370612] 0x000000040000-0x000000050000 : "factory"
    [    0.377663] 0x000000050000-0x000002000000 : "firmware"
    [    0.425570] 2 uimage-fw partitions found on MTD device firmware
    [    0.431621] 0x000000050000-0x000000197930 : "kernel"
    [    0.438344] 0x000000197930-0x000002000000 : "rootfs"
    [    0.445165] mtd: device 5 (rootfs) set to be root filesystem
    [    0.451048] 1 squashfs-split partitions found on MTD device rootfs
    [    0.457343] 0x000000740000-0x000002000000 : "rootfs_data"
    [    0.475237] rt3050-esw 10110000.esw: link changed 0x00
    [    0.482133] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
    [    0.490781] i2c /dev entries driver
    [    0.494891] mt7621_wdt 10000120.watchdog: Initialized
    [    0.501613] NET: Registered protocol family 10
    [    0.510384] NET: Registered protocol family 17
    [    0.514988] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
    [    0.527856] 8021q: 802.1Q VLAN Support v1.8
    [    0.538879] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
    [    0.547013] Freeing unused kernel memory: 164K (803e7000 - 80410000)
    [    1.572444] init: Console is alive
    [    1.576219] init: - watchdog -
    [    4.111202] kmodloader: loading kernel modules from /etc/modules-boot.d/*
    [    4.237144] usbcore: registered new interface driver usbfs
    [    4.242803] usbcore: registered new interface driver hub
    [    4.248363] usbcore: registered new device driver usb
    [    4.259896] exFAT: Version 1.2.9
    [    4.303936] SCSI subsystem initialized
    [    4.314434] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    4.322878] ehci-platform: EHCI generic platform driver
    [    4.338575] phy phy-10120000.usbphy.0: remote usb device wakeup disabled
    [    4.345379] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz
    [    4.350725] ehci-platform 101c0000.ehci: EHCI Host Controller
    [    4.356606] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
    [    4.364765] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
    [    4.385851] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
    [    4.393366] hub 1-0:1.0: USB hub found
    [    4.397611] hub 1-0:1.0: 1 port detected
    [    4.406638] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    4.414573] ohci-platform: OHCI generic platform driver
    [    4.420235] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
    [    4.427205] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
    [    4.435318] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
    [    4.501001] hub 2-0:1.0: USB hub found
    [    4.505261] hub 2-0:1.0: 1 port detected
    [    4.522706] MTK MSDC device init.
    [    4.566004] mtk-sd: MediaTek MT6575 MSDC Driver
    [    4.574019] sdhci: Secure Digital Host Controller Interface driver
    [    4.580369] sdhci: Copyright(c) Pierre Ossman
    [    4.586326] sdhci-pltfm: SDHCI platform and OF driver helper
    [    4.596685] usbcore: registered new interface driver usb-storage
    [    4.606383] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
    [    4.624200] init: - preinit -
    [    5.475711] rt3050-esw 10110000.esw: link changed 0x00
    Press the [f] key and hit [enter] to enter failsafe mode
    Press the [1], [2], [3] or [4] key and hit [enter] to select the debug[    5.674190] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
     level
    [    8.936405] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
    [    8.943853] jffs2_build_filesystem(): unlocking the mtd device... done.
    [    8.950590] jffs2_build_filesystem(): erasing all blocks after the end marker... 
    [    9.116626] rt3050-esw 10110000.esw: link changed 0x01
    [   81.195846] random: nonblocking pool is initialized
    [  139.860715] done.
    [  139.862726] jffs2: notice: (399) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [  139.880050] mount_root: overlay filesystem has not been fully initialized yet
    [  139.891914] mount_root: switching to jffs2 overlay
    - config restore -
    [  140.199079] urandom-seed: Seed file not found (/etc/urandom.seed)
    [  140.321070] procd: - early -
    [  140.324115] procd: - watchdog -
    [  141.045965] procd: - watchdog -
    [  141.049438] procd: - ubus -
    [  141.104366] procd: - init -
    Please press Enter to activate this console.
    [  141.533685] kmodloader: loading kernel modules from /etc/modules.d/*
    [  141.572591] ntfs: driver 2.1.32 [Flags: R/O MODULE].
    [  141.642103] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [  141.668493] gdma-rt2880 10002800.gdma: revision: 3, channels: 16
    [  142.123231] 
    [  142.123231] 
    [  142.123231] === pAd = c0611000, size = 1182848 ===
    [  142.123231] 
    [  142.134138] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
    [  142.206745] Linux video capture interface: v2.00
    [  142.250330] hidraw: raw HID events driver (C) Jiri Kosina
    [  142.275339] ralink-i2s 10000a00.i2s: mclk 480KHz
    [  142.306473] max98090 0-0010: Unrecognized revision 0xff
    [  142.311790] max98090 0-0010: Mismatch in DT specified CODEC type.
    [  142.320578] max98090 0-0010: use default 2.8v micbias
    [  142.339828] asoc-simple-card sound: HiFi <-> 10000a00.i2s mapping ok
    [  142.383534] Bluetooth: Core ver 2.21
    [  142.387387] NET: Registered protocol family 31
    [  142.391898] Bluetooth: HCI device and connection manager initialized
    [  142.398384] Bluetooth: HCI socket layer initialized
    [  142.403337] Bluetooth: L2CAP socket layer initialized
    [  142.408514] Bluetooth: SCO socket layer initialized
    [  142.415983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [  142.421384] Bluetooth: BNEP filters: protocol multicast
    [  142.426743] Bluetooth: BNEP socket layer initialized
    [  142.438587] usbcore: registered new interface driver btusb
    [  142.448245] usbcore: registered new interface driver cdc_acm
    [  142.453997] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    [  142.466045] Bluetooth: HCI UART driver ver 2.3
    [  142.470568] Bluetooth: HCI UART protocol H4 registered
    [  142.475776] Bluetooth: HCI UART protocol BCSP registered
    [  142.485385] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [  142.491489] Bluetooth: HIDP socket layer initialized
    [  142.499713] ip_tables: (C) 2000-2006 Netfilter Core Team
    [  142.521170] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
    [  142.551751] Bluetooth: RFCOMM TTY layer initialized
    [  142.556799] Bluetooth: RFCOMM socket layer initialized
    [  142.562036] Bluetooth: RFCOMM ver 1.11
    [  142.573700] spidev spi32766.1: buggy DT: spidev listed directly in DT
    [  142.580320] ------------[ cut here ]------------
    [  142.585023] WARNING: CPU: 0 PID: 482 at drivers/spi/spidev.c:720 init_module+0x4d33c/0x4ddec [spidev]()
    [  142.594562] Modules linked in: spidev(+) snd_usbmidi_lib slhc rfcomm nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables hidp hid_generic hci_uart crc_ccitt cdc_acm btusb btintel bnep bluetooth snd_soc_simple_card snd_soc_ralink_i2s snd_soc_wm8960 snd_soc_max98090 videobuf2_vmalloc videobuf2_memops videobuf2_core hid v4l2_common videodev evdev snd_soc_core mt_wifi ralink_gdma virt_dma ledtrig_oneshot ledtrig_morse ledtrig_heartbeat ledtrig_gpio ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables msdos snd_pcm_dmaengine snd_compress snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd input_core soundcore vfat fat ntfs configfs autofs4 nls_utf8 nls_iso8859_1 nls_cp437 regmap_i2c dma_shared_buffer ecb cmac mmc_block usb_storage sdhci_pltfm sdhci mtk_sd mmc_core leds_gpio ohci_platform ohci_hcd ledtrig_transient ehci_platform ehci_hcd sd_mod scsi_mod gpio_button_hotplug ext4 jbd2 mbcache exfat usbcore nls_base usb_common crc16 cryptomgr aead crypto_null crc32c_generic crypto_hash
    [  142.701497] CPU: 0 PID: 482 Comm: kmodloader Not tainted 4.4.74 #0
    [  142.707775] Stack : 80380780 00000000 00000001 803d0000 87d21bac 803cae63 80361c18 000001e2
    	  80413438 0000000f 0000001a 024000c0 80066378 8004af58 80367120 803c0000
    	  00000003 0000000f 80365524 8750bb4c 80066378 80048ec4 00000000 00000000
    	  00000001 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    	  00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    	  ...
    [  142.743927] Call Trace:
    [  142.746481] [<80066378>] module_sect_show+0x0/0x18
    [  142.751349] [<8004af58>] vprintk_default+0x24/0x30
    [  142.756241] [<80066378>] module_sect_show+0x0/0x18
    [  142.761103] [<80048ec4>] printk+0x2c/0x38
    [  142.765185] [<8002552c>] warn_slowpath_common+0xa0/0xd0
    [  142.770518] [<8014de3c>] dump_stack+0x14/0x28
    [  142.774941] [<80014908>] show_stack+0x50/0x84
    [  142.779375] [<8002552c>] warn_slowpath_common+0xa0/0xd0
    [  142.784684] [<86c6433c>] init_module+0x4d33c/0x4ddec [spidev]
    [  142.790527] [<86c60000>] 0x86c60000
    [  142.794082] [<800255e4>] warn_slowpath_null+0x18/0x24
    [  142.799240] [<801fb304>] of_match_node+0x20/0x44
    [  142.803943] [<86c60000>] 0x86c60000
    [  142.807506] [<86c6433c>] init_module+0x4d33c/0x4ddec [spidev]
    [  142.813357] [<801c0a10>] devm_kfree+0x20/0x44
    [  142.817811] [<801e1bd8>] spi_drv_probe+0x3c/0x84
    [  142.822508] [<801bd540>] driver_probe_device+0x120/0x288
    [  142.827934] [<8008b928>] kstrdup+0x44/0x8c
    [  142.832107] [<801e1ad8>] spi_match_device+0x38/0xa8
    [  142.837097] [<801bd724>] __driver_attach+0x7c/0xb4
    [  142.841961] [<801bb948>] next_device+0x10/0x30
    [  142.846491] [<801bd6a8>] __driver_attach+0x0/0xb4
    [  142.851264] [<801bba04>] bus_for_each_dev+0x9c/0xac
    [  142.856230] [<80303c9c>] klist_add_tail+0x24/0x50
    [  142.861001] [<86c60000>] 0x86c60000
    [  142.864540] [<801bb7d8>] bus_get+0x2c/0x50
    [  142.868733] [<801bcc38>] bus_add_driver+0xec/0x20c
    [  142.873603] [<800ae92c>] exact_match+0x0/0x8
    [  142.877956] [<800aee34>] exact_lock+0x0/0x24
    [  142.882290] [<86c60000>] 0x86c60000
    [  142.885838] [<86c60000>] 0x86c60000
    [  142.889380] [<801bde3c>] driver_register+0xa8/0xf8
    [  142.894242] [<86c17000>] init_module+0x0/0xdc [spidev]
    [  142.899476] [<86c60000>] 0x86c60000
    [  142.903022] [<86c60000>] 0x86c60000
    [  142.906575] [<86c60000>] 0x86c60000
    [  142.910119] [<86c17098>] init_module+0x98/0xdc [spidev]
    [  142.915429] [<80159a08>] kasprintf+0x1c/0x28
    [  142.919793] [<800458b0>] __wake_up+0x24/0x48
    [  142.924129] [<86c17000>] init_module+0x0/0xdc [spidev]
    [  142.929378] [<8000d938>] do_one_initcall+0x1e8/0x214
    [  142.934430] [<800458b0>] __wake_up+0x24/0x48
    [  142.938780] [<86c17000>] init_module+0x0/0xdc [spidev]
    [  142.944013] [<80034568>] call_usermodehelper_exec+0x144/0x160
    [  142.949880] [<80034058>] call_usermodehelper_setup+0x38/0xa8
    [  142.955649] [<80066378>] module_sect_show+0x0/0x18
    [  142.960551] [<80067598>] do_init_module+0x74/0x1cc
    [  142.965426] [<8009f418>] __vunmap+0xf0/0x114
    [  142.969812] [<80068e2c>] load_module+0x16c0/0x1b68
    [  142.974679] [<80066964>] unknown_module_param_cb+0x0/0xac
    [  142.980177] [<8009f90c>] __vmalloc_node+0x34/0x40
    [  142.984977] [<80069368>] SyS_init_module+0x94/0x180
    [  142.989946] [<80069404>] SyS_init_module+0x130/0x180
    [  142.995016] [<8000682c>] syscall_common+0x30/0x54
    [  142.999814] [<80008c58>] __bzero+0xbc/0x164
    [  143.004058] 
    [  143.005570] ---[ end trace ff208f03df823542 ]---
    [  143.021454] usbcore: registered new interface driver ums-alauda
    [  143.030599] usbcore: registered new interface driver ums-cypress
    [  143.039786] usbcore: registered new interface driver ums-datafab
    [  143.048734] usbcore: registered new interface driver ums-freecom
    [  143.057851] usbcore: registered new interface driver ums-isd200
    [  143.067059] usbcore: registered new interface driver ums-jumpshot
    [  143.076137] usbcore: registered new interface driver ums-karma
    [  143.085788] usbcore: registered new interface driver ums-sddr09
    [  143.094902] usbcore: registered new interface driver ums-sddr55
    [  143.104349] usbcore: registered new interface driver ums-usbat
    [  143.116668] usbcore: registered new interface driver usbhid
    [  143.122331] usbhid: USB HID core driver
    [  143.130053] usbcore: registered new interface driver usblp
    [  143.144154] usbcore: registered new interface driver usbserial
    [  143.150290] usbcore: registered new interface driver usbserial_generic
    [  143.157066] usbserial: USB Serial support registered for generic
    [  143.175705] Driver for 1-wire Dallas network protocol.
    [  143.202174] xt_time: kernel timezone is -0000
    [  143.208956] usbcore: registered new interface driver ch341
    [  143.214646] usbserial: USB Serial support registered for ch341-uart
    [  143.223487] usbcore: registered new interface driver cp210x
    [  143.229342] usbserial: USB Serial support registered for cp210x
    [  143.238905] usbcore: registered new interface driver ftdi_sio
    [  143.244850] usbserial: USB Serial support registered for FTDI USB Serial Device
    [  143.267139] usbcore: registered new interface driver pl2303
    [  143.272908] usbserial: USB Serial support registered for pl2303
    [  143.284428] PPP generic driver version 2.4.2
    [  143.292067] NET: Registered protocol family 24
    [  143.310518] usbcore: registered new interface driver snd-usb-audio
    [  143.332505] usbcore: registered new interface driver uvcvideo
    [  143.338405] USB Video Class driver (1.1.1)
    [  143.351219] usbcore: registered new interface driver option
    [  143.357081] usbserial: USB Serial support registered for GSM modem (1-port)
    [  143.369591] kmodloader: done loading kernel modules from /etc/modules.d/*
    [  154.027323] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready
    [  154.575225] 
    [  154.575225] _      _____   ___  ___    _________  ___  ____
    [  154.575225] | | /| / / _ | / _ \/ _ \  / ___/ __ \/ _ \/ __/ V1.0
    [  154.575225] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/  
    [  154.575225] |__/|__/_/ |_/_/|_/_/     \___/\____/_/|_/___/  
    [  154.575225] 		   Onion Enhanced MT7688 WiFi Driver 
    [  154.575225] 
    [  154.912908] DMA Scheduler Mode=0(LMAC)
    [  154.916828] efuse_probe: efuse = 10000012
    [  154.920951] 1. Phy Mode = 14
    [  155.091057] 2. Phy Mode = 14
    [  155.094027] 3. Phy Mode = 14
    [  155.113549] 	WTBL Segment 1 info:
    [  155.116981] 		MemBaseAddr/FID:0x28000/0
    [  155.120869] 		EntrySize/Cnt:32/128
    [  155.124313] 	WTBL Segment 2 info:
    [  155.127690] 		MemBaseAddr/FID:0x40000/0
    [  155.131576] 		EntrySize/Cnt:64/128
    [  155.135019] 	WTBL Segment 3 info:
    [  155.138402] 		MemBaseAddr/FID:0x42000/64
    [  155.142376] 		EntrySize/Cnt:64/128
    [  155.145831] 	WTBL Segment 4 info:
    [  155.149191] 		MemBaseAddr/FID:0x44000/128
    [  155.153252] 		EntrySize/Cnt:32/128
    [  162.989341] device ra0 entered promiscuous mode
    [  162.994091] br-wlan: port 1(ra0) entered forwarding state
    [  162.999683] br-wlan: port 1(ra0) entered forwarding state
    [  163.006409] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready
    [  164.995816] br-wlan: port 1(ra0) entered forwarding state
    [  169.385452] device ra0 left promiscuous mode
    [  169.389984] br-wlan: port 1(ra0) entered disabled state
    [  169.687414] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready
    [  170.909551] device ra0 entered promiscuous mode
    [  170.914300] br-wlan: port 1(ra0) entered forwarding state
    [  170.919894] br-wlan: port 1(ra0) entered forwarding state
    [  170.926517] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready
    [  172.915816] br-wlan: port 1(ra0) entered forwarding state
    
    
    
    BusyBox v1.25.1 () built-in shell (ash)
    
       ____       _             ____
      / __ \___  (_)__  ___    / __ \__ _  ___ ___ ____ _
     / /_/ / _ \/ / _ \/ _ \  / /_/ /  ' \/ -_) _ `/ _ `/
     \____/_//_/_/\___/_//_/  \____/_/_/_/\__/\_, /\_,_/
     W H A T  W I L L  Y O U  I N V E N T ? /___/
     -----------------------------------------------------
       Ω-ware: 0.2.0 b178
     -----------------------------------------------------
    root@Omega-99A5:/# ifconfig
    apcli0    Link encap:Ethernet  HWaddr 40:A3:6B:C0:99:A6  
              inet6 addr: fe80::42a3:6bff:fec0:99a6/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
    
    br-wlan   Link encap:Ethernet  HWaddr 40:A3:6B:C0:99:A5  
              inet addr:192.168.3.1  Bcast:192.168.3.255  Mask:255.255.255.0
              inet6 addr: fd1d:48c4:7633::1/60 Scope:Global
              inet6 addr: fe80::42a3:6bff:fec0:99a5/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 B)  TX bytes:3975 (3.8 KiB)
    
    eth0      Link encap:Ethernet  HWaddr 40:A3:6B:C0:99:A7  
              inet addr:192.168.100.2  Bcast:192.168.100.255  Mask:255.255.255.0
              inet6 addr: fe80::42a3:6bff:fec0:99a7/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:67 errors:0 dropped:6 overruns:0 frame:0
              TX packets:125 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:9165 (8.9 KiB)  TX bytes:18583 (18.1 KiB)
              Interrupt:5 
    
    lo        Link encap:Local Loopback  
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:65536  Metric:1
              RX packets:48 errors:0 dropped:0 overruns:0 frame:0
              TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1 
              RX bytes:3786 (3.6 KiB)  TX bytes:3786 (3.6 KiB)
    
    ra0       Link encap:Ethernet  HWaddr 40:A3:6B:C0:99:A5  
              inet6 addr: fe80::42a3:6bff:fec0:99a5/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
              Interrupt:6
    

    I think you have some Ethernet related problem.
    I didn't have message like this 'generated random MAC address' and it seems your kernel bug is related to ifconfig:

    [    0.481335] mtk_soc_eth 10100000.ethernet: generated random MAC address 9e:27:c0:7c:bd:c6
    
    ...
    
    [   24.435870] DMA Scheduler Mode=0(LMAC)
    [   24.439704] efuse_probe: efuse = 10000012
    [   24.443826] 1. Phy Mode = 14
    [   24.611598] ERROR: initialization error 781:
    [   24.611598] buffer=303030303030303030306138
    [   24.611598]
    [   24.729924] ERROR: initialization error 781:
    [   24.729924] buffer=303030303030303030306138
    [   24.729924]
    [   25.289526] ERROR: initialization error 781:
    [   25.289526] buffer=303030303030303030306138
    [   25.289526]
    [   53.739438]
    [   53.739438] _      _____   ___  ___    _________  ___  ____
    [   53.739438] | | /| / / _ | / _ \/ _ \  / ___/ __ \/ _ \/ __/ V1.0
    [   53.739438] | |/ |/ / __ |/ , _/ ___/ / /__/ /_/ / , _/ _/
    [   53.739438] |__/|__/_/ |_/_/|_/_/     \___/\____/_/|_/___/
    [   53.739438]             Onion Enhanced MT7688 WiFi Driver
    [   53.739438]
    [   53.896622] Kernel bug detected[#1]:
    [   53.900278] CPU: 0 PID: 1414 Comm: ifconfig Tainted: G        W       4.4.74 #0
    [   53.907693] task: 87dce338 ti: 86a52000 task.ti: 86a52000
    [   53.913162] $ 0   : 00000000 80410000 00000001 ffff9fdc
    [   53.918480] $ 4   : c062302c ffff9fe6 86e765f0 c062302c
    [   53.923790] $ 8   : 0000001c c0609238 86e41f2c 00000000
    [   53.929101] $12   : 00000000 b7924e27 00000000 00000000
    [   53.934410] $16   : c062302c 00090000 000b0000 86f40000
    [   53.939721] $20   : c062302c c0602000 00000001 7fcf296c
    [   53.945032] $24   : 00000018 80043388
    [   53.950342] $28   : 86a52000 86a53c78 00000000 86e52630
    [   53.955654] Hi    : 00000000
    [   53.958570] Lo    : 0000000a
    [   53.961506] epc   : 80053f18 add_timer+0x8/0x14
    [   53.966615] ra    : 86e52630 RTMPSetTimer+0x80/0x110 [mt_wifi]
    [   53.972527] Status: 1100e503 KERNEL EXL IE
    [   53.976783] Cause : 10800034 (ExcCode 0d)
    [   53.980847] PrId  : 00019655 (MIPS 24KEc)
    

    You should try to upgrade your O2+ via wireless (without Ethernet Expansion or at least disconnect the Ethernet cable.)

    Good luck!



  • After upgrading over with serial and ethernet, all I get is this scolling up the screen:
    [ 369.981057] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 370.019143] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 370.059875] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 370.113232] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 424.879220] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 424.947187] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 424.986553] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 425.026006] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 425.061904] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 479.966092] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 479.996253] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 480.034854] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 480.074321] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 534.873030] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 534.957502] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 534.998870] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 535.036707] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 535.076570] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 589.872711] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 589.957030] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 589.993053] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 590.030340] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 590.064870] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 644.861528] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 644.973002] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 645.010152] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 645.049228] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [ 645.086362] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!

    root@Omega-954C:/# cat /etc/config/wireless

    config wifi-device 'radio0'
    option type 'ralink'
    option variant 'mt7628'
    option country 'US'
    option hwmode '11g'
    option htmode 'HT40'
    option channel 'auto'
    option disabled '0'
    option device_mode 'apsta'
    option op_mode 'preference'

    I'm in the UK, not in the US, so should wifisetup ask me where I am?



  • @György-Farkas Thanks for the suggestion. I tried that and got the same result. I am going to try and upgrade a different unit tomorrow and see how that goes.



  • I stumbled across a possible wifi fix for some people. Our wireless network is on 192.168.3.X, and I happened to notice that the ethernet bridge stub is pre-configured as 192.168.3.1. I changed the ethernet bridge stub IP address to 192.168.5.1 (a network we don't use), and my wifi started working.

    If you're having wifi issues on a 192.168.3.X network, try editing /etc/config/network, look for the 'wlan' interface, and change "option ipaddr '192.168.3.1'" to "option ipaddr '192.168.5.1'" (or some other network not in used).



  • With this new OS release is there a way to disable to default AP? I can't use this in anything with a large security hole like that!



  • @Rickard I'm afraid not. I was trying to edit the /etc/config/wireless file and restart the wireless adapter after that.
    It seems the situation is not changed.

    Omega2+ v0.2.0 b178

    config wifi-device 'radio0'
            option type 'ralink'
            option variant 'mt7628'
            option country 'US'
            option hwmode '11g'
            option htmode 'HT40'
            option channel 'auto'
            option disabled '0'
            option device_mode 'apsta'
            option op_mode 'preference'
    
    config wifi-iface 'ap'
            option device 'radio0'
            option mode 'ap'
            option network 'wlan'
            option ifname 'ra0'
            option encryption 'psk2'
            option key '12345678'
            option disabled '0'
            option ssid 'Omega-99A5'
    
    config wifi-iface 'sta'
            option device 'radio0'
            option mode 'sta'
            option ifname 'apcli0'
            option encryption 'psk2'
            option network 'wwan'
            option disabled '0'
            option key 'MyPassword'
            option ssid 'DIGI-xxxx'
    
    config wifi-config
            option key 'MyPassword'
            option ssid 'DIGI-xxxx'
            option encryption 'psk2'
    
    

    The wifi will turn off totally if you set option disabled '1' either in the wifi-device 'radio0' section or in the wifi-iface 'ap' section (or in both;)
    but you can turn off only the wifi station in the wifi-iface 'sta' section.

    Please could you explain why is "a large security hole" a working WiFi AP with a strong password on Omega2(+)?



  • @György-Farkas In the stable version of the Omega2 i could not access the Wi-Fi AP Settings on the web console so i was just thinking it was disables as it said nothing of the Wi-Fi AP in the start up guide. So i got very surprised when i was going to setup my second Omega2 and saw the the AP from the first one. The normal thing here would be to disable the AP until the user asked for it again. Now i have had a Omega2 running in my network for months with a default AP and password! It is like if D-link would send out routers with a predefined WiFi password. So if you can't disable the AP make sure the guide helps you change the password else it is just like running a open AP for everyone!



  • @Paul-Cousins Same exact thing happened. Can’t believe how accurate you stated.

    What worked for me was to make backup copies, then copied the original config files from /rom/ to /etc/

    cp -rf /rom/etc/config/ /etc/config/
    cp -rf /rom/etc/dnsmasq.conf /etc/
    cp -rf /rom/etc/rc.local /etc/

    This sets back working system.



  • Any news on this? http://community.onion.io/topic/2246/cannot-satisfy-dependencies-for-kmod-usb-net-rndis
    It is still not possible to install rndis 😞


  • administrators

    For anyone experiencing issues with WiFi after upgrading, it's likely that your Omega still has the configuration and wifi programs from the previous firmware, but is now running the new driver (which is not compatible with the old configs).
    If you're in this situation, I would recommend to back-up anything you don't want to lose from the Omega to a USB and perform a factory reset. The same effect can be achieved with @michael-bourque 's method above

    More WiFi Fixes

    Also, we've been investigating some of the open issues with WiFi and have made more fixes.

    Here's the updated list:

    • WPA2
      • AES works
      • AES+TKIP works
      • TKIP works - connects within ~20 seconds as of b182
    • WPA (out-dated and should not be used)
      • AES works - connects within ~20 seconds as of b182
      • AES+TKIP works - connects within ~20 seconds as of b182
      • TKIP works
    • WEP (out-dated and should not be used)
      • Shared Key Authentication works
      • Open System Authentication does not work
    • Open Networks (not secure and should not be used)
      • Works as of b178

    Kernel Module Installation

    It is now possible to install additional kernel modules on your Omega but the following conditions must be met:

    • Your Omega must be on the very latest available firmware
      • If you're on b181 and b182 is available, the installation will not work
    • The kernel modules must be from the Onion Package Repo (no kernel modules from the LEDE/OpenWRT package repos can be installed)

    If there are kernel modules you would like to use that are not in our package repo, please let us know and we'll do our best to include them in a timely fashion.



  • @michael-bourque thanks for that! 🙂 I left the device alone for a couple of weeks and then updated to b183 - it is now stable and connecting to wifi on it's own like it should. I am not going to use it on my production devices yet though - still need to put it through it's paces but I think all will be ok going forward!



  • Still not working on mine

    BusyBox v1.25.1 () built-in shell (ash)
    
       ____       _             ____
      / __ \___  (_)__  ___    / __ \__ _  ___ ___ ____ _
     / /_/ / _ \/ / _ \/ _ \  / /_/ /  ' \/ -_) _ `/ _ `/
     \____/_//_/_/\___/_//_/  \____/_/_/_/\__/\_, /\_,_/
     W H A T  W I L L  Y O U  I N V E N T ? /___/
     -----------------------------------------------------
       Ω-ware: 0.2.0 b186
     -----------------------------------------------------
    root@Omega-954C:/# wifisetup
    Onion Omega Wifi Setup
    
    Select from the following:
    1) Scan for Wifi networks
    2) Type network info
    q) Exit
    
    Selection: [  158.218846] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  158.247982] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  158.392033] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  158.428506] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    1
    Scanning for wifi networks...
    
    Select Wifi network:
    1) DTLap
    2) VM715599-2G
    3) BTHub5-NZX5
    4) BTWifi-with-FON
    5) BTWifi-X
    
    Selection: 1
    Network: DTLap
    Encryption type: psk2
    Enter password: ------------
    
    > Restarting wifimanager for changes to take effect
    root@Omega-954C:/# [  202.387422] br-wlan: port 1(ra0) entered disabled state
    [  202.405863] device ra0 left promiscuous mode
    [  202.410317] br-wlan: port 1(ra0) entered disabled state
    [  202.445062] IPv6: ADDRCONF(NETDEV_UP): br-wlan: link is not ready
    [  205.587298] device ra0 entered promiscuous mode
    [  205.592048] br-wlan: port 1(ra0) entered forwarding state
    [  205.597659] br-wlan: port 1(ra0) entered forwarding state
    [  205.604563] IPv6: ADDRCONF(NETDEV_CHANGE): br-wlan: link becomes ready
    [  207.593494] br-wlan: port 1(ra0) entered forwarding state
    [  213.206477] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  213.257154] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  213.297049] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  213.333887] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  213.371294] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  268.221646] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  268.290390] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  268.324915] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  268.366434] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  268.404523] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  323.221315] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  323.268246] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  323.301804] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  323.338575] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  323.378340] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  378.211357] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  378.276980] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  378.314991] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  378.355244] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  378.392214] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  433.225179] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  433.291803] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  433.331354] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  433.370975] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    [  433.414573] APPeerProbeReqAction():shiang! PeerProbeReqSanity failed!
    
    

  • administrators

    @austin-Sandford can you run wifisetup -debug and post the output?



  • This post is deleted!


  • Managed to connect to my Mikrotik AP with the b186 !! Hurrah !!

    Just changed the Channel Band in CAPsMan to 2Ghz-g/n and that's it!!. It WORKED!!! 
    
    Ofc with the previous versions I played with this but it didn't work.


  • The new OS release has Kernel crashes when trying to do things with Audio. I cannot seem to run through these steps without a crash:
    https://onion.io/2bt-omega-i2s-audio/



Looks like your connection to Community was lost, please wait while we try to reconnect.