Defective Hardware (Mini-Dock) | Serial connection not working correctly | Factory Firmware defective
as long as we are talking defective hardware lets give a big shout out to the gps expansion. onion admits a fault in the unit and at the same times claims it's not their fault. yes, according to another poster onion claims gps expansion faults that they admit exist are not their fault. so good luck with the mini dock. i can confirm though that the expansion dock has a good serial connect if that interests you at all.
@Douglas-Kryder Well, are you talking about the old expansion-dock for the Omega1, or the newer one for the Omega2? And if you're talking about the old one, does it match with the schematics at https://github.com/OnionIoT/Onion-Hardware/blob/master/Schematics/Omega-Expansion-Dock.pdf ? The Omega1 mini-dock these guys have doesn't match the schematics, so that's a problem.
@WereCatf i was talking about the one released with the omega2 group of products.
OK, i made a ticket for the onioneers i will give feedback when i get ...
#5898 freshdesk ticket.
The answer from Onion:
There was problems with resistor in serial circuit of old mini dock. But it works with Omega1. Since we never promise compatibility between old mini dock and new Omega2, there is nothing we can do about this. If you want to use Omega 2 with mini dock, I suggest that you can buy a mini dock 2 to solve this problem.
And by the way, i was mentioning my problems i also had with the Omega1 setup and my mini-docks. I had to change hardware that i see the dock permanent when it is plugged in over USB.
Onion.io just ignores such facts, not responding on question ppl make here or just do so if everything would be ok.
A normal client without a lot of technical readings knowledge just assumes that there is one version of a mini-dock ... a working , free of bugs, on.
At least when he is paying 15.- Dollars and about 70% taxes on it (x2) !!
The schematic show clearly one version of mini-dock ... the working one ! and compatible with omega2/2p
It is really easy, the stupid client is always the one who is the idiot!
How did you take this excellent photo (what kind of apparate, settings) please?
If I understand well there can be at least two (or three?) Minidock versions. Which one is this?
Thank you in advance for your answer,
Firstly I'm partly sorry for reviving the old thread; but I've butted my head against this same problem.
@onion can you fix your documentation so we can track these changes and make the necessary adjustments to our boards? Suggesting simply buying the mini dock 2 when there is no such item for sale isn't making this any less frustrating. I must admit I had completely forgotten about these things until I was looking to replace Hi-link RM04 modules, their next model was pretty much identical and I saw an opportunity to get my work to support the open source community ... but when I couldn't even get a serial connection going after an hour the powers to be pulled the plug. However I'd still like to sort this out for my own use.
I borrowed the rewards from a friend who also backed the 2 and 2+ and his dock is identical to mine. Neither work.
@bearer The Omega-Mini-Dock schematic is basically correct. This can be the version2 board with original Omega header pinout (U5). For Omega2(+) one should replace U5 to a correct header pinout and change RXD, TXD to RX0, TX0 respectively.
There are no TVS diodes (D12, D13, D14) on the Minidock.
Only these are the hardware differences between the Minidock versions:
R77, R83, R84 are 1 kOhm SMD resistors (marking 102) on the v1 board
R77, R83, R84 are 3 kOhm SMD resistors (marking 302) on the v2 board
To fix the problems of the Minidock version1 board is fairly simple:
- remove / desolder the R77, R83 and R84 resistors - IMHO this is the best solution :-)
- or solder a 0 Ohm (or a piece of wire) to the top of the R76, R81 and R82 resistors (ie. replace them with 0 Ohm)
- or change R77, R83 and R84 1 kOhm to 3 kOhm (so you'll have a genuine version2 Minidock ;-)
I hope all above info are correct but - as usual - make these modifications at your own risk.
Do you want further background info?
Thanks for the detailed reply. I went with option 3 and managed to fit some 0805 onto the 0603 pads and it works as expected. Thanks again.