1-Wire Temperature Sensor - DS18B20 - on Omega2

[Jari Myllys]

I get also this gpio error . When Onion correct this to firmware?? I have firmware 0.1.9 (b149) and it don't work!!! Please do something!!

[Costas Costas]

@Lazar-Demin any idea when 1-wire will be returned to the firmware so we can all hook up our sensors?

[John Quin]

This is basically the "hello world" of sensors programs and it is broken. I'm beginning to wonder if the MKR1000 would have been a better option.

[Costas Costas]

Onion issued a post on GitHub that they are planning to look at 1-wire this week.

[Robert Wenzel]

firmware update arrived:

b151

February 2, 2017

• Added patch to fix 1-wire master issue where virtual nodes were not accepted as gpios
• Infra: added option for quick (essential) compile
• Infra: reorganized patches

I guess they patched it, will check later...

As far as I can tell it is working did my first reading.

Following the Omega (1) instructions:

https://wiki.onion.io/Tutorials/Reading-1Wire-Sensor-Data

[Costas Costas]

How do we do an upgrade to b151 without losing everything we have installed to /usr/bin?

[Costas Costas]

Confirmed as working fine on my 2+

[Robert Wenzel]

@Costas-Costas Did you find a solution for your backup problem?

[Costas Costas]

Nope, reinstalling now.

[Chris Stratton]

At a crude level you could probably do something like tar up everything in /overlay to /tmp, and scp that off. The question would be if you could then put it back exactly, or if you would have to do so piece by piece. If changes to the underlying system are small it might go back exactly.

But LEDE/openwrt normally have their own backup capability when doing a sysupgrade.

[Bertalan Gergaly]

It is still not working for me. I just upgraded to the b151 firmware. I got the directory /sys/devices/w1_bus_master1, but I got slave entries like:

root@omega:/sys/devices/w1_bus_master1# ls -1d ??-*
00-100000000000
00-900000000000
00-e00000000000

And it keeps changing. But I never see the correct serial number of the device.

[Costas Costas]

@Bertalan-Gergaly that suggests you haven't wired up the sensor correctly.

[Bertalan Gergaly]

My first thought was exactly that. So I redid the wires before posting. Same result.

I did a check just now. The data pin is not connected to the omega, just the ground and the power and I still got the weird devices:

root@omega:/sys/devices/w1_bus_master1# ls -1d ??-*
00-400000000000
00-c00000000000

And I just did a retest without anything connected to the omega and I still got the weird devices:

root@omega:/sys/devices/w1_bus_master1# ls -1d ??-*
00-400000000000
00-800000000000

[Chris Stratton]

@Bertalan-Gergaly said

I did a check just now. The data pin is not connected to the omega, just the ground and the power and I still got the weird devices:

Is something pulling up the data line as required for 1-wire?

If the line is floating, odd results should not be unexpected.

Try it again with a 4.7 K resistor (or for a temporary experiment, anything from 1K - 10K) between the data line and the 3.3 v rail.

[Bertalan Gergaly]

OK, I got it working. I had to change the power supply from a phone charger to a 'real' power supply.

[Vaclav VESELY]

@Bertalan-Gergaly what you mean by "phone charger to a 'real' power supply"? I have the USB cable connected to my computer, using screen to admin my Omega2, so I am powering my Omega2 via the USB cable out of my PC. What is the good power setup? Thank you.

[Bertalan Gergaly]

@Vaclav-VESELY Probably my phone charger was giving out less than 5V and that affected my O2+ or the DS18B20. Now I'm using a Meanwell RS-15-5 adjustable power supply (http://www.meanwell.com/webapp/product/search.aspx?prod=RS-15)

[Lazar Demin]

As @Robert-Wenzel mentioned, b151 fixes the one-wire issue

Here's a new article on using One-Wire with the Omega2: https://docs.onion.io/omega2-docs/communicating-with-1w-devices.html

Happy hacking!

[Vaclav VESELY]

@Lazar-Demin perfect. All works correctly now. I appreciate the speed of Onion team and the power of the community.

[Joris Mulliez]

Thanks @Lazar-Demin for the correction.

But it seems not to work on my omega 2+.

I just upgrade my firmware, and try to follow the tutorial you mentioned.
But I can't see my DS18B20... I see only slaves like : "00-800000000000" it seems "fake".

First question : the sensor must be plugged into the board before or after omega started ?

And here is my output when I just install the "master" one-wire, without plug any sensor :

# insmod w1-gpio-custom bus0=0,19,0
[  100.959174] Custom GPIO-based W1 driver version 0.1.1
root@Omega-0000:/# [  102.882550] w1_master_driver w1_bus_master1: w1_search: max_slave_count 64 reached, will continue next search.
[  150.298561] w1_master_driver w1_bus_master1: Family 0 for 00.800000000000.8c is not registered
[  209.629280] w1_master_driver w1_bus_master1: Family 0 for 00.400000000000.46 is not registered.
root@Omega-0000:/# cat /sys/devices/w1_bus_master1/w1_master_slaves
00-800000000000
00-400000000000
[  257.010981] w1_master_driver w1_bus_master1: Family 0 for 00.c00000000000.ca is not registered.
root@Omega-0000:/# cat /sys/devices/w1_bus_master1/w1_master_slaves
00-400000000000
00-c00000000000

So there is "ghost" sensors appearing automatically, and If I try to plug my real sensor, I can't see him...

Am I doing something wrong ?

Thanks for your help,