Omega 2S+: No WiFi Support with OpenWRT 21.02
-
@crispyoz @Lazar-Demin Hi both , I'm really disappointed, it doesn't work:
network file:root@OpenWrt:/# cat /etc/init.d/network #!/bin/sh /etc/rc.common START=20 STOP=90 USE_PROCD=1 init_switch() { setup_switch() { return 0; } include /lib/network setup_switch } start_service() { init_switch procd_open_instance procd_set_param command /sbin/netifd procd_set_param respawn procd_set_param watch network.interface [ -e /proc/sys/kernel/core_pattern ] && { procd_set_param limits core="unlimited" } procd_close_instance } reload_service() { local rv=0 init_switch ubus call network reload || rv=1 /sbin/wifi reload_legacy return $rv } stop_service() { /sbin/wifi down ifdown -a sleep 1 } validate_atm_bridge_section() { uci_validate_section network "atm-bridge" "${1}" \ 'unit:uinteger:0' \ 'vci:range(32, 65535):35' \ 'vpi:range(0, 255):8' \ 'atmdev:uinteger:0' \ 'encaps:or("llc", "vc"):llc' \ 'payload:or("bridged", "routed"):bridged' } validate_route_section() { uci_validate_section network route "${1}" \ 'interface:string' \ 'target:cidr4' \ 'netmask:netmask4' \ 'gateway:ip4addr' \ 'metric:uinteger' \ 'mtu:uinteger' \ 'table:or(range(0,65535),string)' } validate_route6_section() { uci_validate_section network route6 "${1}" \ 'interface:string' \ 'target:cidr6' \ 'gateway:ip6addr' \ 'metric:uinteger' \ 'mtu:uinteger' \ 'table:or(range(0,65535),string)' } validate_rule_section() { uci_validate_section network rule "${1}" \ 'in:string' \ 'out:string' \ 'src:cidr4' \ 'dest:cidr4' \ 'tos:range(0,31)' \ 'mark:string' \ 'invert:bool' \ 'lookup:or(range(0,65535),string)' \ 'goto:range(0,65535)' \ 'action:or("prohibit", "unreachable", "blackhole", "throw")' } validate_rule6_section() { uci_validate_section network rule6 "${1}" \ 'in:string' \ 'out:string' \ 'src:cidr6' \ 'dest:cidr6' \ 'tos:range(0,31)' \ 'mark:string' \ 'invert:bool' \ 'lookup:or(range(0,65535),string)' \ 'goto:range(0,65535)' \ 'action:or("prohibit", "unreachable", "blackhole", "throw")' } validate_switch_section() { uci_validate_section network switch "${1}" \ 'name:string' \ 'enable:bool' \ 'enable_vlan:bool' \ 'reset:bool' \ 'ar8xxx_mib_poll_interval:uinteger' \ 'ar8xxx_mib_type:range(0,1)' } validate_switch_vlan() { uci_validate_section network switch_vlan "${1}" \ 'device:string' \ 'vlan:uinteger' \ 'ports:list(ports)' } service_triggers() { procd_add_reload_trigger network wireless procd_open_validate validate_atm_bridge_section validate_route_section [ -e /proc/sys/net/ipv6 ] && validate_route6_section validate_rule_section [ -e /proc/sys/net/ipv6 ] && validate_rule6_section validate_switch_section validate_switch_vlan procd_close_validate } shutdown() { ifdown -a sleep 1 }Could you please share the config file you've used for your openwrt 22.03 ?
Could you please this network file maybe I've missed something here?
-
@IBH Here are the config files from the Onion-customized 22.03.3 firmware.
Note that this is the default configuration setup for client mode on ethernet and hosting a WiFi AP.
To connect to a wifi network, you can follow the WiFi STA section in our technical doc for this firmware.Also, keep in mind
/etc/init.d/networkdefines the network service, not the network configuration.
/etc/config/network:config interface 'loopback' option device 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config globals 'globals' option ula_prefix 'fd16:9810:ecb2::/48' config device option name 'br-lan' option type 'bridge' config interface 'lan' option device 'br-lan' option proto 'static' option netmask '255.255.255.0' option ip6assign '60' option ipaddr '192.168.4.1' config switch option name 'switch0' option reset '1' option enable_vlan '0' config interface 'wan' option proto 'dhcp' option device 'eth0' option hostname 'Omega-f19f' config interface 'wlan' option device 'ra0' option proto 'static' option ipaddr '192.168.3.1' option netmask '255.255.255.0' option ip6assign '60' config interface 'wwan' option proto 'dhcp' option device 'apcli0' option hostname 'Omega-f19f'
/etc/config/wireless:config wifi-device 'radio0' option type 'mac80211' option path 'platform/10300000.wmac' option band '2g' option disabled '0' option channel 'auto' option htmode 'HT40' config wifi-iface 'default_radio0' option device 'radio0' option mode 'ap' option ifname 'ra0' option network 'wlan' option ssid 'Omega-f19f' option encryption 'psk2' option key '12345678' config wifi-iface 'client' option device 'radio0' option network 'wwan' option mode 'sta' option ssid 'MySSID' option key 'MyKey' option encryption 'psk2' option ifname 'apcli0' option disabled '1'
/etc/config/firewall:config defaults option syn_flood '1' option input 'ACCEPT' option output 'ACCEPT' option forward 'REJECT' config zone option name 'lan' list network 'lan' list network 'wlan' option input 'ACCEPT' option output 'ACCEPT' option forward 'ACCEPT' config zone option name 'wan' list network 'wan' list network 'wwan' option output 'ACCEPT' option masq '1' option mtu_fix '1' option input 'ACCEPT' option forward 'ACCEPT' config forwarding option src 'lan' option dest 'wan' config rule option name 'Allow-DHCP-Renew' option src 'wan' option proto 'udp' option dest_port '68' option target 'ACCEPT' option family 'ipv4' config rule option name 'Allow-Ping' option src 'wan' option proto 'icmp' option icmp_type 'echo-request' option family 'ipv4' option target 'ACCEPT' config rule option name 'Allow-IGMP' option src 'wan' option proto 'igmp' option family 'ipv4' option target 'ACCEPT' config rule option name 'Allow-DHCPv6' option src 'wan' option proto 'udp' option dest_port '546' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-MLD' option src 'wan' option proto 'icmp' option src_ip 'fe80::/10' list icmp_type '130/0' list icmp_type '131/0' list icmp_type '132/0' list icmp_type '143/0' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-ICMPv6-Input' option src 'wan' option proto 'icmp' list icmp_type 'echo-request' list icmp_type 'echo-reply' list icmp_type 'destination-unreachable' list icmp_type 'packet-too-big' list icmp_type 'time-exceeded' list icmp_type 'bad-header' list icmp_type 'unknown-header-type' list icmp_type 'router-solicitation' list icmp_type 'neighbour-solicitation' list icmp_type 'router-advertisement' list icmp_type 'neighbour-advertisement' option limit '1000/sec' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-ICMPv6-Forward' option src 'wan' option dest '*' option proto 'icmp' list icmp_type 'echo-request' list icmp_type 'echo-reply' list icmp_type 'destination-unreachable' list icmp_type 'packet-too-big' list icmp_type 'time-exceeded' list icmp_type 'bad-header' list icmp_type 'unknown-header-type' option limit '1000/sec' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-IPSec-ESP' option src 'wan' option dest 'lan' option proto 'esp' option target 'ACCEPT' config rule option name 'Allow-ISAKMP' option src 'wan' option dest 'lan' option dest_port '500' option proto 'udp' option target 'ACCEPT'
-
@Lazar-Demin I'm not using onion openwrt , I prefer keep using openwrt base and I need to have the .config file I don't know why @crispyoz 's build image worked fine and not mine .
-
@IBH These config files should still be helpful. Onion's (beta) Openwrt 22.03 firmware is based on the openwrt base, including the mt76 wifi driver.
The only customizations so far are different default configurations for better usability out of the box.Assuming your firmware has been built properly, the config files from my previous post should setup:
- the ethernet port to act as a DHCP client
- the WiFi AP to broadcast
And will allow you to use a few uci commands to connect to an existing Wifi network.
-
@Lazar-Demin Hi, my need is to connect my phone/my laptop etc to my onion wifi and not to connect my onion to wifi .
-
@IBH please add the to the top of your PROCD_DEBUG=1 /etc/init.d/network (after the shebang) and then run service network restart, then run logread and check for errors
-
@IBH said in Omega 2S+: No WiFi Support with OpenWRT 21.02:
my need is to connect my phone/my laptop etc to my onion wifi and not to connect my onion to wifi .
Like I said above, the configuration in the config files I shared will enable the Omega's WiFi AP.
If they don't work out of the box, I suggest following @crispyoz's suggestion.
-
@Lazar-Demin @crispyoz , sorry for the delay , I was busy with some other projects.
I've tried @crispyoz 's suggestion and I got this output :root@OpenWrt:/# service network restart { "name": "network" } [ 226.822353] rt3050-esw 10110000.esw: port 0 link down { "name": "network", "script": "\/etc\/init.d\/network", "instances": { "instance1": { "command": [ "\/sbin\/netifd" ], "respawn": [ "3600", "5", "5" ], "watch": [ "network.interface" ], "limits": { "core": "unlimited" } } }, "triggers": [ [ "config.change", [ "if", [ "eq", "package", "network" ], [ "run_script", "\/etc\/init.d\/network", "reload" ] ], 1000 ], [ "config.change", [ "if", [ "eq", "package", "wireless" ], [ "run_script", "\/etc\/init.d\/network", "reload" ] ], 1000 ] ], "validate": [ { "package": "network", "type": "atm-bridge", "data": { "unit": "uinteger", "vci": "range(32, 65535)", "vpi": "range(0, 255)", "atmdev": "uinteger", "encaps": "or(llc, vc)", "payload": "or(bridged, routed)" } }, { "package": "network", "type": "route", "data": { "interface": "string", "target": "cidr4", "netmask": "ne tmask4", "gateway": "ip4addr", "metric": "uinteger", "mtu": "uinteger", "table": "or(range(0,65535),string)" } }, { "package": "network", "type": "route6", "data": { "interface": "string", "target": "cidr6", "gateway": "ip6addr", "metric": "uinteger", "mtu": "uinteger", "ta ble": "or(range(0,65535),string)" } }, { "package": "network", "type": "rule", "data": { "in": "string", "out": "string", "src": "cidr4", "dest": "cidr4", "tos": "range(0,31)", "mark": "string", "invert": "bool", "lookup": "or(range(0,65535),string)", "goto": "range(0,65535 )", "action": "or(prohibit, unreachable, blackhole, throw)" } }, { "package": "network", "type": "rule6", "data": { "in": "string", "out": "string", "src": "cidr6", "dest": "cidr6", "tos": "range(0,31)", "mark": "string", "invert": "bool", "lookup": "or(range(0,65535),strin g)", "goto": "range(0,65535)", "action": "or(prohibit, unreachable, blackhole, throw)" } }, { "package": "network", "type": "switch", "data": { "name": "string", "enable": "bool", "enable_vlan": "bool", "reset": "bool", "ar8xxx_mib_poll_interval": "uinteger", "ar8xxx_mib_ty pe": "range(0,1)" } }, { "package": "network", "type": "switch_vlan", "data": { "device": "string", "vlan": "uinteger", "ports": "list(ports)" } } ], "data": { } } root@OpenWrt:/# [ 231.143315] rt3050-esw 10110000.esw: port 0 link up root@OpenWrt:/# logread Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.000000] Linux version 5.10.176 (ibenhassen@beast) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r0+20130-31b1366bc6) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Sun Apr 23 12:15:54 2023 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Board has DDR2 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Analog PMU set to hw control Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Digital PMU set to hw control Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] printk: bootconsole [early0] enabled Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] MIPS: machine is Onion Omega2+ Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Zone ranges: Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Movable zone start for each node Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Early memory node ranges Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.000000] On node 0 totalpages: 32768 Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.000000] Normal zone: 256 pages used for memmap Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Writing ErrCtl register=00070c90 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Readback ErrCtl register=00070c90 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] Memory: 121980K/131072K available (4815K kernel code, 588K rwdata, 1068K rodata, 1200K init, 195K bss, 9092K reserved, 0K cma-reserved) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] NR_IRQS: 256 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] intc: using register map from devicetree Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] CPU Clock: 580MHz Sun Apr 23 12:24:41 2023 kern.crit kernel: [ 0.000000] timer_probe: no matching timers found Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.007649] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.073596] pid_max: default: 32768 minimum: 301 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.078230] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.085248] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.094860] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.106325] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.115824] futex hash table entries: 256 (order: -1, 3072 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.122395] pinctrl core: initialized pinctrl subsystem Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.129155] NET: Registered protocol family 16 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.204262] clocksource: Switched to clocksource MIPS Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.210487] NET: Registered protocol family 2 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.215020] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.222708] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.230834] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.238205] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.245004] TCP: Hash tables configured (established 1024 bind 1024) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.251296] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.257628] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.264672] NET: Registered protocol family 1 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.268852] PCI: CLS 0 bytes, default 32 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.279760] workingset: timestamp_bits=30 max_order=15 bucket_order=0 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.290237] squashfs: version 4.0 (2009/01/31) Phillip Lougher Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.295892] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.308468] mt7621_gpio 10000600.gpio: registering 32 gpios Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.314066] mt7621_gpio 10000600.gpio: registering 32 gpios Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.319760] mt7621_gpio 10000600.gpio: registering 32 gpios Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.325504] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.332760] printk: console [ttyS0] disabled Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.337006] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.345742] printk: console [ttyS0] enabled Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.354135] printk: bootconsole [early0] disabled Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.364594] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.374440] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.384945] spi-mt7621 10000b00.spi: sys_freq: 193333333 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.406004] ------------[ cut here ]------------ Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.410736] WARNING: CPU: 0 PID: 1 at drivers/mtd/spi-nor/core.c:3008 spi_nor_init+0x1b8/0x1c0 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.419548] enabling reset hack; may not recover from unexpected reboots Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.426351] Modules linked in: Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.429464] CPU: 0 PID: 1 Comm: swapper Not tainted 5.10.176 #0 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.435484] Stack : 80640000 80559874 00000000 00000000 80c1b9e4 80780000 805d0000 80535428 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.443986] 80c282fc 805c9d07 807833b4 00000001 807b0000 00000001 80c1b998 e6063e0c Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.452495] 00000000 00000000 80535428 80c1b838 ffffefff 00000000 00000000 ffffffea Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.461002] 00000000 80c1b844 0000004d 805d0098 00000000 00000009 80c1ba78 802e8aa0 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.469509] 00000009 807b0000 808b4acc 80ce1200 00000018 802ae0dc 00000000 80780000 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.478016] ... Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.480501] Call Trace: Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.483003] [<80007240>] show_stack+0x30/0x100 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.487534] [<80026ab8>] __warn+0xb0/0x11c Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.491694] [<80026bb0>] warn_slowpath_fmt+0x8c/0xac Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.496748] [<802e8aa0>] spi_nor_init+0x1b8/0x1c0 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.501524] [<802e9a78>] spi_nor_scan+0x6e0/0xb1c Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.506311] [<802e9f48>] spi_nor_probe+0x94/0x314 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.511092] [<802be3e0>] really_probe+0x108/0x4d8 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.515877] [<802bc048>] bus_for_each_drv+0x70/0xb0 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.520829] [<802be9e4>] __device_attach+0x114/0x1cc Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.525880] [<802bd350>] bus_probe_device+0xa0/0xbc Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.530852] [<802b8fc0>] device_add+0x390/0x7a8 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.535464] [<802f1e28>] spi_add_device+0xc0/0x1c8 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.540327] [<802f2868>] spi_register_controller+0x7fc/0xb34 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.546089] [<802f4e24>] mt7621_spi_probe+0x190/0x1e8 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.551223] [<802c0794>] platform_drv_probe+0x28/0x80 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.556362] [<802be3e0>] really_probe+0x108/0x4d8 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.561138] [<802bef18>] device_driver_attach+0x124/0x134 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.566627] [<802befa4>] __driver_attach+0x7c/0x158 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.571578] [<802bbf9c>] bus_for_each_dev+0x68/0xa4 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.576539] [<802bd624>] bus_add_driver+0x150/0x238 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.581490] [<802bf788>] driver_register+0x98/0x154 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.586452] [<80000638>] do_one_initcall+0x50/0x1b4 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.591416] [<80654f3c>] kernel_init_freeable+0x1e0/0x278 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.596921] [<804ad028>] kernel_init+0x10/0xf8 Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.601436] [<800026b8>] ret_from_kernel_thread+0x14/0x1c Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.606922] Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.608476] ---[ end trace 0fd428f03a722194 ]--- Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.613644] spi-nor spi0.0: w25q256 (32768 Kbytes) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.618649] 4 fixed-partitions partitions found on MTD device spi0.0 Sun Apr 23 12:24:41 2023 kern.err kernel: [ 0.625185] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions Sun Apr 23 12:24:41 2023 kern.err kernel: [ 0.632626] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions Sun Apr 23 12:24:41 2023 kern.err kernel: [ 0.640649] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions Sun Apr 23 12:24:41 2023 kern.err kernel: [ 0.648145] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.655840] Creating 4 MTD partitions on "spi0.0": Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.660727] 0x000000000000-0x000000030000 : "u-boot" Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.668806] 0x000000030000-0x000000040000 : "u-boot-env" Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.675479] 0x000000040000-0x000000050000 : "factory" Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.683310] 0x000000050000-0x000002000000 : "firmware" Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.690009] 2 uimage-fw partitions found on MTD device firmware Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.696101] Creating 2 MTD partitions on "firmware": Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.701155] 0x000000000000-0x0000001ed974 : "kernel" Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.706212] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.717277] 0x0000001ed974-0x000001fb0000 : "rootfs" Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.722333] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.732822] mtd: setting mtd5 (rootfs) as root device Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.738970] 1 squashfs-split partitions found on MTD device rootfs Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 0.745329] 0x0000006a0000-0x000001fb0000 : "rootfs_data" Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.802421] rt3050-esw 10110000.esw: mediatek esw at 0xb0110000, irq 25 initialized Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.811181] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.821563] NET: Registered protocol family 10 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.831182] Segment Routing with IPv6 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.835153] NET: Registered protocol family 17 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.839738] 8021q: 802.1Q VLAN Support v1.8 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.852252] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.866371] Freeing unused kernel memory: 1200K Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 0.870968] This architecture does not have kernel memory protection. Sun Apr 23 12:24:41 2023 kern.info kernel: [ 0.877553] Run /sbin/init as init process Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.881702] with arguments: Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.881708] /sbin/init Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.881713] with environment: Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.881719] HOME=/ Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 0.881725] TERM=linux Sun Apr 23 12:24:41 2023 user.info kernel: [ 1.588563] init: Console is alive Sun Apr 23 12:24:41 2023 user.info kernel: [ 1.592604] init: - watchdog - Sun Apr 23 12:24:41 2023 user.info kernel: [ 2.975806] kmodloader: loading kernel modules from /etc/modules-boot.d/* Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.111035] usbcore: registered new interface driver usbfs Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.116809] usbcore: registered new interface driver hub Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.122307] usbcore: registered new device driver usb Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.135729] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.145019] ohci-platform: OHCI generic platform driver Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.160843] phy phy-10120000.usbphy.0: remote usb device wakeup disabled Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.167661] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.172960] ohci-platform 101c1000.ohci: Generic Platform OHCI controller Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.179885] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 1 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.188066] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.269389] hub 1-0:1.0: USB hub found Sun Apr 23 12:24:41 2023 kern.info kernel: [ 3.274013] hub 1-0:1.0: 1 port detected Sun Apr 23 12:24:41 2023 user.info kernel: [ 3.328227] kmodloader: done loading kernel modules from /etc/modules-boot.d/* Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 3.336343] mtk-sd 10130000.sdhci: no support for card's volts Sun Apr 23 12:24:41 2023 kern.err kernel: [ 3.342280] mmc0: error -22 whilst initialising SDIO card Sun Apr 23 12:24:41 2023 user.info kernel: [ 3.358399] init: - preinit - Sun Apr 23 12:24:41 2023 kern.info kernel: [ 5.087218] rt3050-esw 10110000.esw: port 0 link up Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 5.530614] random: jshn: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 5.652248] random: jshn: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 5.795673] random: jshn: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 6.247207] mtk-sd 10130000.sdhci: no support for card's volts Sun Apr 23 12:24:41 2023 kern.err kernel: [ 6.253151] mmc0: error -22 whilst initialising SDIO card Sun Apr 23 12:24:41 2023 kern.info kernel: [ 6.292357] rt3050-esw 10110000.esw: port 0 link down Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 6.562609] random: procd: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 7.651094] mtk-sd 10130000.sdhci: no support for card's volts Sun Apr 23 12:24:41 2023 kern.err kernel: [ 7.657096] mmc0: error -22 whilst initialising SDIO card Sun Apr 23 12:24:41 2023 kern.info kernel: [ 10.523205] rt3050-esw 10110000.esw: port 0 link up Sun Apr 23 12:24:41 2023 kern.info kernel: [ 10.528247] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 11.030911] jffs2: notice: (404) jffs2_build_xattr_subsystem: complete building xattr subsystem, 9 of xdatum (0 unchecked, 4 orphan) and 10 of xref (4 dead, 0 orphan) found. Sun Apr 23 12:24:41 2023 user.info kernel: [ 11.048668] mount_root: switching to jffs2 overlay Sun Apr 23 12:24:41 2023 kern.warn kernel: [ 11.057068] overlayfs: upper fs does not support tmpfile. Sun Apr 23 12:24:41 2023 user.info kernel: [ 11.125618] procd: - early - Sun Apr 23 12:24:41 2023 user.info kernel: [ 11.128989] procd: - watchdog - Sun Apr 23 12:24:41 2023 user.info kernel: [ 12.102568] procd: - watchdog - Sun Apr 23 12:24:41 2023 user.info kernel: [ 12.107728] procd: - ubus - Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 12.251561] random: ubusd: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 12.260828] random: ubusd: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 12.273591] random: ubusd: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 user.info kernel: [ 12.284401] procd: - init - Sun Apr 23 12:24:41 2023 user.info kernel: [ 13.032741] kmodloader: loading kernel modules from /etc/modules.d/* Sun Apr 23 12:24:41 2023 kern.info kernel: [ 13.412169] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f Sun Apr 23 12:24:41 2023 kern.info kernel: [ 13.419936] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c Sun Apr 23 12:24:41 2023 kern.info kernel: [ 13.480669] xt_time: kernel timezone is -0000 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 13.567250] mt76_wmac 10300000.wmac: ASIC revision: 76280001 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 14.597061] mt76_wmac 10300000.wmac: Firmware Version: 20151201 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 14.603094] mt76_wmac 10300000.wmac: Build Time: 20151201183641 Sun Apr 23 12:24:41 2023 kern.info kernel: [ 14.624269] mt76_wmac 10300000.wmac: firmware init done Sun Apr 23 12:24:41 2023 kern.debug kernel: [ 14.805447] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' Sun Apr 23 12:24:41 2023 user.info kernel: [ 15.076826] kmodloader: done loading kernel modules from /etc/modules.d/* Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 16.836499] random: jshn: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 16.959104] random: ubusd: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:41 2023 kern.notice kernel: [ 16.966053] random: ubus: uninitialized urandom read (4 bytes read) Sun Apr 23 12:24:42 2023 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses! Sun Apr 23 12:24:42 2023 user.notice dnsmasq: Allowing 127.0.0.0/8 responses Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: started, version 2.86 cachesize 150 Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: DNS service limited to local subnets Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: UBus support enabled: connected to system bus Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for test Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for onion Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for localhost Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for local Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for invalid Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for bind Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: using only locally-known addresses for lan Sun Apr 23 12:24:43 2023 daemon.warn dnsmasq[884]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: read /etc/hosts - 4 addresses Sun Apr 23 12:24:43 2023 daemon.info dnsmasq[884]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses Sun Apr 23 12:24:48 2023 kern.notice kernel: [ 24.834290] random: crng init done Sun Apr 23 12:24:48 2023 kern.notice kernel: [ 24.837768] random: 48 urandom warning(s) missed due to ratelimiting Sun Apr 23 12:24:48 2023 authpriv.info dropbear[948]: Not backgrounding Sun Apr 23 12:24:52 2023 kern.info kernel: [ 29.412355] rt3050-esw 10110000.esw: port 0 link down Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: bonding Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: 8021ad Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: 8021q Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: macvlan Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: veth Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: bridge Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: Network device Sun Apr 23 12:24:53 2023 user.notice : Added device handler type: tunnel Sun Apr 23 12:24:56 2023 kern.info kernel: [ 33.517252] rt3050-esw 10110000.esw: port 0 link up Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'loopback' is enabled Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'loopback' is setting up now Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'loopback' is now up Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'wan' is enabled Sun Apr 23 12:24:59 2023 daemon.notice netifd: Network device 'lo' link is up Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'loopback' has link connectivity Sun Apr 23 12:24:59 2023 daemon.notice netifd: Network device 'eth0' link is up Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'wan' has link connectivity Sun Apr 23 12:24:59 2023 daemon.notice netifd: Interface 'wan' is setting up now Sun Apr 23 12:24:59 2023 daemon.notice netifd: wan (1395): udhcpc: started, v1.35.0 Sun Apr 23 12:25:00 2023 daemon.info procd: - init complete - Sun Apr 23 12:25:01 2023 daemon.notice netifd: wan (1395): udhcpc: broadcasting discover Sun Apr 23 12:25:01 2023 daemon.notice netifd: radio0 (1361): sh: acs_survey: out of range Sun Apr 23 12:25:01 2023 daemon.notice netifd: radio0 (1361): sh: acs_survey: out of range Sun Apr 23 12:25:02 2023 daemon.notice netifd: radio0 (1361): ./mac80211.sh: eval: line 573: /usr/sbin/hostapd: not found Sun Apr 23 12:25:02 2023 daemon.notice netifd: Interface 'wlan' is enabled Sun Apr 23 12:25:02 2023 daemon.notice netifd: Interface 'wlan' is setting up now Sun Apr 23 12:25:02 2023 daemon.notice netifd: Interface 'wlan' is now up Sun Apr 23 12:25:03 2023 user.notice firewall: Reloading firewall due to ifup of wlan (ra0) Sun Apr 23 12:25:04 2023 daemon.notice netifd: wan (1395): udhcpc: broadcasting discover Sun Apr 23 12:25:07 2023 daemon.notice netifd: wan (1395): udhcpc: broadcasting discover Sun Apr 23 12:25:32 2023 daemon.notice netifd: radio0 (1361): Command failed: Request timed out Sun Apr 23 12:25:32 2023 daemon.notice netifd: radio0 (1361): Command failed: Not found Sun Apr 23 12:25:32 2023 daemon.notice netifd: radio0 (1361): Device setup failed: HOSTAPD_START_FAILED Sun Apr 23 12:25:32 2023 daemon.notice netifd: Wireless device 'radio0' set retry=0 Sun Apr 23 12:25:32 2023 daemon.crit netifd: Wireless device 'radio0' setup failed, retry=0 Sun Apr 23 12:25:32 2023 daemon.notice netifd: Wireless device 'radio0' is now down Sun Apr 23 12:28:08 2023 daemon.notice netifd: Interface 'loopback' is now down Sun Apr 23 12:28:08 2023 daemon.notice netifd: Interface 'loopback' is disabled Sun Apr 23 12:28:08 2023 daemon.notice netifd: Network device 'lo' link is down Sun Apr 23 12:28:08 2023 daemon.notice netifd: Interface 'loopback' has link connectivity loss Sun Apr 23 12:28:09 2023 daemon.notice netifd: Interface 'wlan' is now down Sun Apr 23 12:28:09 2023 daemon.notice netifd: Interface 'wlan' is disabled Sun Apr 23 12:28:09 2023 daemon.notice netifd: wan (1395): udhcpc: received SIGTERM Sun Apr 23 12:28:09 2023 daemon.notice netifd: wan (1395): udhcpc: entering released state Sun Apr 23 12:28:09 2023 daemon.notice netifd: wan (1395): Command failed: ubus call network.interface notify_proto { "action": 0, "link-up": false, "keep": false, "interface": "wan" } (Permission denied) Sun Apr 23 12:28:09 2023 daemon.notice netifd: Interface 'wan' is now down Sun Apr 23 12:28:09 2023 daemon.notice netifd: Interface 'wan' is disabled Sun Apr 23 12:28:09 2023 daemon.notice netifd: Network device 'eth0' link is down Sun Apr 23 12:28:09 2023 daemon.notice netifd: Interface 'wan' has link connectivity loss Sun Apr 23 12:28:10 2023 kern.info kernel: [ 226.822353] rt3050-esw 10110000.esw: port 0 link down Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: bonding Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: 8021ad Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: 8021q Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: macvlan Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: veth Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: bridge Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: Network device Sun Apr 23 12:28:11 2023 user.notice : Added device handler type: tunnel Sun Apr 23 12:28:11 2023 daemon.notice procd: /etc/init.d/network: { "name": "network" } Sun Apr 23 12:28:14 2023 kern.info kernel: [ 231.143315] rt3050-esw 10110000.esw: port 0 link up Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'loopback' is enabled Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'loopback' is setting up now Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'loopback' is now up Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'wan' is enabled Sun Apr 23 12:28:14 2023 daemon.notice netifd: Network device 'lo' link is up Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'loopback' has link connectivity Sun Apr 23 12:28:14 2023 daemon.notice netifd: Network device 'eth0' link is up Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'wan' has link connectivity Sun Apr 23 12:28:14 2023 daemon.notice netifd: Interface 'wan' is setting up now Sun Apr 23 12:28:15 2023 daemon.notice netifd: wan (1869): udhcpc: started, v1.35.0 Sun Apr 23 12:28:15 2023 daemon.notice netifd: wan (1869): udhcpc: broadcasting discover Sun Apr 23 12:28:16 2023 daemon.notice netifd: radio0 (1846): sh: acs_survey: out of range Sun Apr 23 12:28:16 2023 daemon.notice netifd: radio0 (1846): sh: acs_survey: out of range Sun Apr 23 12:28:17 2023 daemon.notice netifd: radio0 (1846): ./mac80211.sh: eval: line 573: /usr/sbin/hostapd: not found Sun Apr 23 12:28:18 2023 daemon.notice netifd: wan (1869): udhcpc: broadcasting discover Sun Apr 23 12:28:21 2023 daemon.notice netifd: wan (1869): udhcpc: broadcasting discover root@OpenWrt:/#I think hostapd needs to be added to the build image right?
Thank you so much for you both , for your time and suggestions.
-
@IBH said in Omega 2S+: No WiFi Support with OpenWRT 21.02:
image right
@crispyoz I've managed and fixed the issue by getting the hostapd, the wifi is up now , I can my SSSID in the list of the WiFi but I couldn't connect on it . Do I need to make some other configuration?
This my wifi status:root@OpenWrt:/# wifi status { "radio0": { "up": true, "pending": false, "autostart": true, "disabled": false, "retry_setup_failed": false, "config": { "path": "platform/10300000.wmac", "channel": "1", "band": "2g", "htmode": "HT20", "disabled": false }, "interfaces": [ { "section": "default_radio0", "ifname": "wlan0", "config": { "mode": "ap", "ssid": "OpenWrt", "encryption": "none", "network": [ "lan" ], "mode": "ap" }, "vlans": [ ], "stations": [ ] } ] } }
-
@IBH When you try to connect to the hotspot and it fails, what error are you getting? type logread and look for any errors reported by hostapd.
-
@crispyoz I got this:
Sun Apr 23 12:18:53 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:19:12 2023 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:19:12 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: disassociated Sun Apr 23 12:19:13 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE) Sun Apr 23 12:19:24 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: authenticated Sun Apr 23 12:19:24 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: associated (aid 1) Sun Apr 23 12:19:24 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:19:45 2023 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:19:45 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: authenticated Sun Apr 23 12:19:45 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: associated (aid 1) Sun Apr 23 12:19:45 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:22:32 2023 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:22:32 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: disassociated Sun Apr 23 12:22:33 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE) Sun Apr 23 12:22:39 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: authenticated Sun Apr 23 12:22:39 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: associated (aid 1) Sun Apr 23 12:22:39 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:22:51 2023 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:22:51 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: disassociated Sun Apr 23 12:22:52 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
-
@crispyoz I could now connect to the OpenWrt ssid but with no internet connection. Do you have any idea please why?
There is my logs:Sun Apr 23 12:36:15 2023 kern.info kernel: [ 1010.402205] br-lan: port 2(wlan0) entered blocking state Sun Apr 23 12:36:15 2023 kern.info kernel: [ 1010.408376] br-lan: port 2(wlan0) entered disabled state Sun Apr 23 12:36:15 2023 kern.info kernel: [ 1010.415584] device wlan0 entered promiscuous mode Sun Apr 23 12:36:15 2023 kern.info kernel: [ 1010.571804] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Sun Apr 23 12:36:15 2023 kern.info kernel: [ 1010.578739] br-lan: port 2(wlan0) entered blocking state Sun Apr 23 12:36:15 2023 kern.info kernel: [ 1010.585353] br-lan: port 2(wlan0) entered forwarding state Sun Apr 23 12:36:15 2023 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->ENABLED Sun Apr 23 12:36:15 2023 daemon.notice hostapd: wlan0: AP-ENABLED Sun Apr 23 12:36:17 2023 daemon.notice netifd: Wireless device 'radio0' is now up Sun Apr 23 12:36:17 2023 daemon.notice netifd: Network device 'wlan0' link is up Sun Apr 23 12:36:18 2023 daemon.err onionApp[5184]: + exec Sun Apr 23 12:36:20 2023 daemon.info dnsmasq[2786]: read /etc/hosts - 4 addresses Sun Apr 23 12:36:20 2023 daemon.info dnsmasq[2786]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses Sun Apr 23 12:36:20 2023 daemon.info dnsmasq[2786]: read /tmp/hosts/odhcpd - 0 addresses Sun Apr 23 12:36:20 2023 daemon.info dnsmasq-dhcp[2786]: read /etc/ethers - 0 addresses Sun Apr 23 12:36:28 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: authenticated Sun Apr 23 12:36:28 2023 daemon.info hostapd: wlan0: STA fa:89:87:9c:e5:ee IEEE 802.11: associated (aid 1) Sun Apr 23 12:36:28 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED fa:89:87:9c:e5:ee Sun Apr 23 12:36:28 2023 daemon.info dnsmasq-dhcp[2786]: DHCPREQUEST(br-lan) 192.168.3.225 fa:89:87:9c:e5:ee Sun Apr 23 12:36:28 2023 daemon.info dnsmasq-dhcp[2786]: DHCPACK(br-lan) 192.168.3.225 fa:89:87:9c:e5:ee root@OpenWrt:/#
-
@IBH This is covered in the docs
-
@crispyoz Hi, I don't have the wifisetup command :
root@OpenWrt:/# wifisetup
/bin/ash: wifisetup: not found
-
@crispyoz Could you please share your /etc/config/firewall file?
root@OpenWrt:/# cat /tmp/dhcp.leases
1682298022 32:e8:eb:f4:bf:dd 192.168.3.249 * 01:32:e8:eb:f4:bf:dd
-
@Lazar-Demin Now, I have the wifi AP , I can connect my phone to onion wifi but with no internet connection. I've checked the firewall configuration and it looks like the doc shared by @crispyoz .Also I got this output :
root@OpenWrt:/# cat /tmp/dhcp.leases 1682298022 32:e8:eb:f4:bf:dd 192.168.3.249 * 01:32:e8:eb:f4:bf:ddAny help please?
-
@IBH How is your Omega connected to the internet? Ethernet or wifi?
Like I mentioned in another thread, you should expect that a lot of the existing Omega2 documentation probably won't work out of the box on the new beta firmware (or any firmware based on newer OpenWRT versions).
So while firmware based on newer openwrt doesn't have the Onion-specific
wifisetuputility, the same concepts will apply. Meaning you should still check that your firewall is configured to allow input, output, and forwarding between the network interface with the internet connection and the Omega's Wi-Fi AP.Let us know how it goes.
-
@IBH I think this is the key firewall rule:
config zone
option name 'wan'
list network 'wan'
list network 'wwan'
option output 'ACCEPT'
option masq '1'
option mtu_fix '1'
option input 'ACCEPT'
option forward 'ACCEPT'It causes masquerading of the sta through the ap.
