Omega 2S+: No WiFi Support with OpenWRT 21.02
-
@crispyoz
root@OpenWrt:/# iw list
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x1 RX 0x1
Configured Antennas: TX 0x1 RX 0x1
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x17e
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-7
Frequencies:
* 2412 MHz [1] (14.0 dBm)
* 2417 MHz [2] (14.0 dBm)
* 2422 MHz [3] (14.0 dBm)
* 2427 MHz [4] (14.0 dBm)
* 2432 MHz [5] (14.0 dBm)
* 2437 MHz [6] (14.0 dBm)
* 2442 MHz [7] (14.0 dBm)
* 2447 MHz [8] (14.0 dBm)
* 2452 MHz [9] (14.0 dBm)
* 2457 MHz [10] (14.0 dBm)
* 2462 MHz [11] (14.0 dBm)
* 2467 MHz [12] (14.0 dBm) (no IR)
* 2472 MHz [13] (14.0 dBm) (no IR)
* 2484 MHz [14] (14.0 dBm) (no IR)
valid interface combinations:
* #{ IBSS } <= 1, #{ managed, AP, mesh point, P2P-client, P2P-GO } <= 4,
total <= 4, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported extended features:
* [ RRM ]: RRM
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
-
@crispyoz root@OpenWrt:/# iw dev
phy#0
Interface wlan0
ifindex 5
wdev 0x2
addr 40:a3:6b:c3:17:1f
type AP
txpower 14.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
-
@IBH Strange, everything looks correct to me, but iw status does not show the SSID. After you made changes to the wireless file, try rebootig and wait for a minute before running wifi status. Also try making these changes:
uci set wireless.radio0.channel='auto'
uci set wireless.sta.disabled='1'
uci commit wirelessThen reboot.
-
@crispyoz I've tried that too but still no luck
-
@IBH Maybe try using the 21.02 firmware released by OpenWRT: onion_omega2p-squashfs-sysupgrade.bin at https://downloads.openwrt.org/releases/21.02.5/targets/ramips/mt76x8/
If the wifi works using that firmware, then it points to an issue with the customized firmware you've built.
-
@IBH I put my firmware binary on my github, you just need to add the wifi configuration I posted earlier. If that works for you I can share my build config. If the Onin version works for you as provided by @Lazar-Demin go with that one as mine is based up on the standard OpenWrt build.
-
@crispyoz Thank you , we are using same as you an Openwrt build and we don't use onion-openwrt . Will check with your firmware binary and @Lazar-Demin's firmware too. In fact, it is strange that we have the wlan interface and everything looks good but we couldn't see the SSID and have the connection.
-
@IBH I wonder if you tried treating the AP WiFi SSID as hidden and connect manually. Your WiFi command shows he SSID is not configured as hidden but it's just a thought. Anyway we know my config works on my build so the answer is there somewhere.
Looking at the bigger picture, you probably should be using OpenWrt 22 anyway.
-
@crispyoz Do you know how we can verify if the AP WiFi SSID was treating as hidden ?
For OpenWrt 22, which tag you used for the upgrade from 21 to 22? does it openwrt-22.03 ?
-
@IBH Looking at the output of your "wifi status" command I can see the SSID is not configured to be hidden, I was just pondering if the issue was related to something on your build that caused it to be hidden.
For OpenWrt 22 I used "openwrt-22.03"
-
Hi @crispyoz, wifi works fine with your build image :
Could you please tell me if you have rebased the branch openwrt-22.03 into your branch ? Could you please share the steps you have done for upgrading your openwrt build ?THank you so much for your time and help.
-
@IBH I don't rebase. Just a git clone, then make menuconfig make kernel_menuconfig add my changes to uci defaults and files directories then make.
-
@crispyoz Do you have a GitHub repo where you've pushed your OpenWrt 22.03 clone with your config changes?
In fact, If I'm not wrong you git clone the base OpenWrt 22.03 (https://git.openwrt.org/openwrt/openwrt.git)then you've added your feeds and configs right?
-
@IBH My repo is currently private as I am working on something however here as the simple instructions to set up your build system:
Setup OpenWrt 22.03
cd
git clone https://git.openwrt.org/openwrt/openwrt.git openwrt22
cd openwrt22
scripts/feeds update -a
scripts/feeds install -a
git checkout openwrt-22.03
make menuconfig
Target System (MediaTek Ralink MIPS)
Subtarget (MT76x8 based boards)
Target Profile (Onion Omega2+)Then remove the /etc/config/network and /etc/config/wireless with the settings I gave you earlier in this thread.
-
@crispyoz one suggestion:
dogit checkout openwrt-22.03beforescripts/feeds update -aandscripts/feeds install -aIf you update and install the feeds before changing the branch, you might be using packages meant for the default branch of the openwrt/openwrt repo.
Thefeeds.conf.defaultfile points to different branches of the package repositories depending on the branch of openwrt/openwrt.See
feeds.conf.defaultin the master branch vsfeeds.conf.defaultin the openwrt-22.03 branch:
-
@Lazar-Demin @crispyoz thanks both. I got this after doings your steps:
scripts/config/conf: /lib/x86_64-linux-gnu/libc.so.6: versionGLIBC_2.33' not found (required by scripts/config/conf) scripts/config/conf: /lib/x86_64-linux-gnu/libc.so.6: versionGLIBC_2.34' not found (required by scripts/config/conf)
/home/ibh/projects/onion-22-03/sources/openwrt-22/include/toplevel.mk:118: recipe for target 'defconfig' failed
make: *** [defconfig] Error 1
FYI: I'm using docker for building.
-
@IBH Which docker image are you using?
If it's the
onion/omega2-sourcedocker image mentioned in https://github.com/OnionIoT/source#options-for-using-the-build-system, I would recommend against compiling OpenWRT 21 and 22 with this image since it's based on Ubuntu 18.I suggest spinning up a new ubuntu 22.04 container and following OpenWRT's build system setup instructions: https://openwrt.org/docs/guide-developer/toolchain/install-buildsystem
-
@IBH use the command ldd --version to determine which verison of glibc you have installed, you may have to install a newer version. Which OS are you building on? Windows/Linux ? As @Lazar-Demin mentioned you can create your own docker container and follow the OpenWrt instructions, personally I install on my Ubuntu system directly without using docker.
-
@crispyoz @Lazar-Demin Hi both , I'm really disappointed, it doesn't work:
network file:root@OpenWrt:/# cat /etc/init.d/network #!/bin/sh /etc/rc.common START=20 STOP=90 USE_PROCD=1 init_switch() { setup_switch() { return 0; } include /lib/network setup_switch } start_service() { init_switch procd_open_instance procd_set_param command /sbin/netifd procd_set_param respawn procd_set_param watch network.interface [ -e /proc/sys/kernel/core_pattern ] && { procd_set_param limits core="unlimited" } procd_close_instance } reload_service() { local rv=0 init_switch ubus call network reload || rv=1 /sbin/wifi reload_legacy return $rv } stop_service() { /sbin/wifi down ifdown -a sleep 1 } validate_atm_bridge_section() { uci_validate_section network "atm-bridge" "${1}" \ 'unit:uinteger:0' \ 'vci:range(32, 65535):35' \ 'vpi:range(0, 255):8' \ 'atmdev:uinteger:0' \ 'encaps:or("llc", "vc"):llc' \ 'payload:or("bridged", "routed"):bridged' } validate_route_section() { uci_validate_section network route "${1}" \ 'interface:string' \ 'target:cidr4' \ 'netmask:netmask4' \ 'gateway:ip4addr' \ 'metric:uinteger' \ 'mtu:uinteger' \ 'table:or(range(0,65535),string)' } validate_route6_section() { uci_validate_section network route6 "${1}" \ 'interface:string' \ 'target:cidr6' \ 'gateway:ip6addr' \ 'metric:uinteger' \ 'mtu:uinteger' \ 'table:or(range(0,65535),string)' } validate_rule_section() { uci_validate_section network rule "${1}" \ 'in:string' \ 'out:string' \ 'src:cidr4' \ 'dest:cidr4' \ 'tos:range(0,31)' \ 'mark:string' \ 'invert:bool' \ 'lookup:or(range(0,65535),string)' \ 'goto:range(0,65535)' \ 'action:or("prohibit", "unreachable", "blackhole", "throw")' } validate_rule6_section() { uci_validate_section network rule6 "${1}" \ 'in:string' \ 'out:string' \ 'src:cidr6' \ 'dest:cidr6' \ 'tos:range(0,31)' \ 'mark:string' \ 'invert:bool' \ 'lookup:or(range(0,65535),string)' \ 'goto:range(0,65535)' \ 'action:or("prohibit", "unreachable", "blackhole", "throw")' } validate_switch_section() { uci_validate_section network switch "${1}" \ 'name:string' \ 'enable:bool' \ 'enable_vlan:bool' \ 'reset:bool' \ 'ar8xxx_mib_poll_interval:uinteger' \ 'ar8xxx_mib_type:range(0,1)' } validate_switch_vlan() { uci_validate_section network switch_vlan "${1}" \ 'device:string' \ 'vlan:uinteger' \ 'ports:list(ports)' } service_triggers() { procd_add_reload_trigger network wireless procd_open_validate validate_atm_bridge_section validate_route_section [ -e /proc/sys/net/ipv6 ] && validate_route6_section validate_rule_section [ -e /proc/sys/net/ipv6 ] && validate_rule6_section validate_switch_section validate_switch_vlan procd_close_validate } shutdown() { ifdown -a sleep 1 }Could you please share the config file you've used for your openwrt 22.03 ?
Could you please this network file maybe I've missed something here?
-
@IBH Here are the config files from the Onion-customized 22.03.3 firmware.
Note that this is the default configuration setup for client mode on ethernet and hosting a WiFi AP.
To connect to a wifi network, you can follow the WiFi STA section in our technical doc for this firmware.Also, keep in mind
/etc/init.d/networkdefines the network service, not the network configuration.
/etc/config/network:config interface 'loopback' option device 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config globals 'globals' option ula_prefix 'fd16:9810:ecb2::/48' config device option name 'br-lan' option type 'bridge' config interface 'lan' option device 'br-lan' option proto 'static' option netmask '255.255.255.0' option ip6assign '60' option ipaddr '192.168.4.1' config switch option name 'switch0' option reset '1' option enable_vlan '0' config interface 'wan' option proto 'dhcp' option device 'eth0' option hostname 'Omega-f19f' config interface 'wlan' option device 'ra0' option proto 'static' option ipaddr '192.168.3.1' option netmask '255.255.255.0' option ip6assign '60' config interface 'wwan' option proto 'dhcp' option device 'apcli0' option hostname 'Omega-f19f'
/etc/config/wireless:config wifi-device 'radio0' option type 'mac80211' option path 'platform/10300000.wmac' option band '2g' option disabled '0' option channel 'auto' option htmode 'HT40' config wifi-iface 'default_radio0' option device 'radio0' option mode 'ap' option ifname 'ra0' option network 'wlan' option ssid 'Omega-f19f' option encryption 'psk2' option key '12345678' config wifi-iface 'client' option device 'radio0' option network 'wwan' option mode 'sta' option ssid 'MySSID' option key 'MyKey' option encryption 'psk2' option ifname 'apcli0' option disabled '1'
/etc/config/firewall:config defaults option syn_flood '1' option input 'ACCEPT' option output 'ACCEPT' option forward 'REJECT' config zone option name 'lan' list network 'lan' list network 'wlan' option input 'ACCEPT' option output 'ACCEPT' option forward 'ACCEPT' config zone option name 'wan' list network 'wan' list network 'wwan' option output 'ACCEPT' option masq '1' option mtu_fix '1' option input 'ACCEPT' option forward 'ACCEPT' config forwarding option src 'lan' option dest 'wan' config rule option name 'Allow-DHCP-Renew' option src 'wan' option proto 'udp' option dest_port '68' option target 'ACCEPT' option family 'ipv4' config rule option name 'Allow-Ping' option src 'wan' option proto 'icmp' option icmp_type 'echo-request' option family 'ipv4' option target 'ACCEPT' config rule option name 'Allow-IGMP' option src 'wan' option proto 'igmp' option family 'ipv4' option target 'ACCEPT' config rule option name 'Allow-DHCPv6' option src 'wan' option proto 'udp' option dest_port '546' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-MLD' option src 'wan' option proto 'icmp' option src_ip 'fe80::/10' list icmp_type '130/0' list icmp_type '131/0' list icmp_type '132/0' list icmp_type '143/0' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-ICMPv6-Input' option src 'wan' option proto 'icmp' list icmp_type 'echo-request' list icmp_type 'echo-reply' list icmp_type 'destination-unreachable' list icmp_type 'packet-too-big' list icmp_type 'time-exceeded' list icmp_type 'bad-header' list icmp_type 'unknown-header-type' list icmp_type 'router-solicitation' list icmp_type 'neighbour-solicitation' list icmp_type 'router-advertisement' list icmp_type 'neighbour-advertisement' option limit '1000/sec' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-ICMPv6-Forward' option src 'wan' option dest '*' option proto 'icmp' list icmp_type 'echo-request' list icmp_type 'echo-reply' list icmp_type 'destination-unreachable' list icmp_type 'packet-too-big' list icmp_type 'time-exceeded' list icmp_type 'bad-header' list icmp_type 'unknown-header-type' option limit '1000/sec' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-IPSec-ESP' option src 'wan' option dest 'lan' option proto 'esp' option target 'ACCEPT' config rule option name 'Allow-ISAKMP' option src 'wan' option dest 'lan' option dest_port '500' option proto 'udp' option target 'ACCEPT'
